Page 5869 of 5883

FRONT WASHER NOZZLE AND TUBE
WW-67
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
MA
B
WW
N
O
P
FRONT WASHER NOZZLE AND TUBE
Washer Tube LayoutINFOID:0000000001396458
Removal and InstallationINFOID:0000000001404271
REMOVAL
1. Remove the cowl top cover. Refer to EXT-20, "Removal and Installation" .
2. Disconnect the washer tube from the front washer nozzle.
3. While pressing pawl (A) on the reverse side of front washer noz-
zle (1), remove front washer nozzle (1) from cowl top cover.
INSTALLATION
1. Attach the washer tube to the front washer nozzle.
2. Install the front washer nozzle in the cowl top cover.
3. Install the cowl top cover. Refer to EXT-20, "
Removal and Installation" .
4. Adjust the front washer nozzle spray pattern. Refer to WW-68, "
Adjustment" .
CAUTION:
The spray points are different from side to side, so install the left and right front washer nozzles in
the correct positions.
InspectionINFOID:0000000001404272
CHECK VALVE INSPECTION
1. Front washer nozzle (LH) 2. Front washer nozzle (RH) 3. Joint washer tube
4. Washer tube 5. Clip 6. Clamp
7. Washer tank
SKIB5664E
LKIA0939E
Page 5870 of 5883
WW-68
< ON-VEHICLE REPAIR >
FRONT WASHER NOZZLE AND TUBE
Blow air in the injection direction, and make sure that air flows only
one way. Make sure that the reverse direction is not possible.
AdjustmentINFOID:0000000001404273
Adjust spray positions to match the positions as shown.
Insert a suitable tool into the nozzle hole and move up/down and left/right to adjust to the specified spray
position.
SKIB5665E
1. Windshield A. 395 mm (15.55 in) B. 216 mm (8.50 in)
C. 100 mm (3.94 in) D. 85 mm (3.35 in) E. Black mask
F. 303 mm (11.93 in) G. 212 mm (8.35 in) H. 249 mm (9.80 in)
I. Center of windsheild J. Spray pattern area K. 286 mm (11.26 in)
LKIA0938E
Page 5871 of 5883
FRONT WIPER ARM
WW-69
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
MA
B
WW
N
O
P
FRONT WIPER ARM
Exploded ViewINFOID:0000000001366661
LHD Models
LKIA0786E
1. Front RH wiper blade 2. Front RH wiper arm 3. Wiper arm cap
4. Front wiper drive assembly 5. Front LH wiper arm 6. Wiper arm cap
7. Front LH wiper blade
Page 5872 of 5883
WW-70
< ON-VEHICLE REPAIR >
FRONT WIPER ARM
RHD Models
Removal and InstallationINFOID:0000000001449632
REMOVAL
1. Operate the front wiper to move it to the auto stop position.
2. Open the hood.
3. Remove the front wiper arm caps.
4. Remove the front wiper arm nuts.
5. Raise the front wiper arms, and remove the front wiper arms.
INSTALLATION
1. Clean up the pivot area as shown. This will reduce possibility of
wiper arm looseness.
2. Prior to wiper arm installation, turn on wiper switch to operate
wiper motor and then turn it off (auto stop).
3. Push wiper arm onto pivot shaft, make sure it is correctly
meshed and fully seated on the spline.
ALLIA0278ZZ
1. Wiper arm cap 2. Front RH wiper arm 3. Wiper arm cap
4. Front LH wiper arm 5. Front wiper drive assembly 6. Front LH wiper blade
7. Front RH wiper blade Front
SEL024J
Page 5873 of 5883

FRONT WIPER ARM
WW-71
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
MA
B
WW
N
O
P
4. Lift the blade up and then set it down onto glass surface to set
the blade center to clearance “L1” and “L2” (LHD) or "L3" and
"L4" (RHD) immediately before temporarily tightening the wiper
arm nuts.
5. Spray washer fluid. Turn on wiper switch to operate wiper motor
and then turn it off.
6. Make sure that wiper blades stop are within specifications. Refer
to WW-73, "
Adjustment".
7. Tighten wiper arm nuts to specification.
8. Attach wiper arm caps.
AdjustmentINFOID:0000000001366663
WIPER BLADE POSITION ADJUSTMENT
To adjust the wiper arm stop location, the wiper arm must be
removed and installed.
Clearance between the top edge of cowl top cover and the tip of the
front wiper blade as shown.L1 (LHD) : 37.5±7.5 mm (1.48 ± 0.295 in)
L2 (LHD) : 42.7±7.5 mm (1.68 ± 0.295 in)
L3 (RHD) : 38.0±7.5 mm (1.50 ± 0.295 in)
L4 (RHD) : 39.0±7.5 mm (1.54 ± 0.295 in)
A Cowl top cover top edge
AWLIA0020ZZ
L1 (LHD) : 37.5±7.5 mm (1.48 ± 0.295 in)
L2 (LHD) : 42.7±7.5 mm (1.68 ± 0.295 in)
L3 (RHD) : 38.0±7.5 mm (1.50 ± 0.295 in)
L4 (RHD) : 39.0±7.5 mm (1.54 ± 0.295 in)
A Cowl top cover top edge
AWLIA0020ZZ
Page 5874 of 5883
WW-72
< ON-VEHICLE REPAIR >
FRONT WIPER DRIVE ASSEMBLY
FRONT WIPER DRIVE ASSEMBLY
Exploded ViewINFOID:0000000001450763
LHD Models
LKIA0786E
1. Front RH wiper blade 2. Front RH wiper arm 3. Wiper arm cap
4. Front wiper drive assembly 5. Front LH wiper arm 6. Wiper arm cap
7. Front LH wiper blade
Page 5875 of 5883

FRONT WIPER DRIVE ASSEMBLY
WW-73
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
MA
B
WW
N
O
P
RHD Models
Removal and InstallationINFOID:0000000001450837
REMOVAL
1. Operate the front wiper motor, and then turn off (auto stop).
2. Remove wiper arms. Refer to WW-70, "
Removal and Installation".
3. Remove cowl top cover. Refer to EXT-20, "
Removal and Installation".
4. Disconnect wiper motor connector.
5. Remove front wiper drive assembly bolts, and remove front wiper drive assembly.
INSTALLATION
1. Install front wiper drive assembly.
2. Connect wiper motor connector. Turn wiper switch on to operate wiper motor, then turn wiper switch off
(auto stop).
3. Install cowl top cover. Refer to EXT-20, "
Removal and Installation".
4. Install the wiper arms and adjust as necessary. Refer to WW-71, "
Adjustment".
AdjustmentINFOID:0000000001450764
WIPER BLADE POSITION ADJUSTMENT
ALLIA0278ZZ
1. Wiper arm cap 2. Front RH wiper arm 3. Wiper arm cap
4. Front LH wiper arm 5. Front wiper drive assembly 6. Front LH wiper blade
7. Front RH wiper blade
Page 5876 of 5883
WW-74
< ON-VEHICLE REPAIR >
FRONT WIPER DRIVE ASSEMBLY
To adjust the wiper arm stop location, the wiper arm must be
removed and installed.
Clearance between the top edge of the cowl top cover and the tip of
the front wiper blade as shown.
L1 (LHD) : 37.5±7.5 mm (1.48 ± 0.295 in)
L2 (LHD) : 42.7±7.5 mm (1.68 ± 0.295 in)
L3 (RHD) : 38.0±7.5 mm (1.50 ± 0.295 in)
L4 (RHD) : 39.0±7.5 mm (1.54 ± 0.295 in)
A Cowl top cover top edge
AWLIA0020ZZ