2007 NISSAN TIIDA Trunk

DLK-374
< COMPONENT DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
INTELLIGENT KEY WARNING BUZZER
*: Sedan only
Is the inspection result normal?
YES >> Intelligent Key warning buzzer is OK.
NO >> Replace Intelligent Key warning buzzer. Refer to XX-XX, "*****"
.
Intelligent Key warning buzzer
connectorTerminal Operation
(+) (-)
Buzzer sounds D6 (driver door)
12
B82 (trunk)
*

DLK-380
< COMPONENT DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
INTELLIGENT KEY BATTERY AND FUNCTION
INTELLIGENT KEY BATTERY AND FUNCTION
DescriptionINFOID:0000000001530384
The following functions are available when having and carrying the Intelligent Key.
 Door lock/unlock
 Back door open (hatchback)
 Trunk lid release (sedan)
 Engine start
Remote control entry function is available when operating the remote buttons.
Component Function CheckINFOID:0000000001530385
1.CHECK FUNCTION
With CONSULT-III
Check remote keyless entry receiver "RKE OPE COUN1" in DATA MONITOR mode with CONSULT-III.
Is the inspection result normal?
YES >> Intelligent Key is OK.
NO >> Refer to DLK-380, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000001530386
1.CHECK INTELLIGENT KEY FUNCTION
Do doors lock and unlock when using the Intelligent Key buttons?
YES or NO?
YES >> Intelligent Key is OK.
NO >> GO TO 2.
2.CHECK INTELLIGENT KEY BATTERY
Check by connecting a resistance (approximately 300Ω) so that the
current value becomes about 10 mA.
Is the measurement value within specification?
YES >> Intelligent Key battery is OK.
NO >> Replace Intelligent Key battery.
Component InspectionINFOID:0000000001530387
For battery removal and installation, refer to XX-XX, "*****".
Special Repair RequirementINFOID:0000000001530388
Refer to CONSULT-III Operation Manual.
Monitor item Condition
RKE OPE COUN1 Check that the numerical value is changing while operating the Intelligent Key.
Standard : Approx. 2.5 - 3.0V
OCC0607D

DLK-386
< ECU DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
INTELLIGENT KEY UNIT
29*3Ground VTrunk opener request
switchInputTrunk opener
request
switchON (Pressed) 0
OFF (Released) 5
30 Ground GR Security indicator lamp OutputIgnition
switch OFFWhen security indi-
cator lamp is ON0
When security indi-
cator lamp is OFFBattery voltage
31 Ground BR Steering lock unit ground — — — 0
32 Ground GRSteering lock unit com-
municationInput/
OutputSteering lockLOCK status 5
LOCK or UNLOCK
35 Ground LFront console antenna
(+)OutputIgnition knob
is pressed.When Intelligent Key
is in the antenna de-
tection area
When Intelligent Key
is not in the antenna
detection area
36 Ground P Front console antenna (-) OutputIgnition knob
is pressed.When Intelligent Key
is in the antenna de-
tection area
When Intelligent Key
is not in the antenna
detection area Te r m i n a l N o .
Wire
colorDescription
ConditionVa l u e [ V ]
(Approx.)
Signal nameInput/
Output +–
JMKIA0433ZZ
JMKIA0393ZZ
JMKIA0391ZZ
JMKIA0392ZZ
JMKIA0390ZZ

BCM (BODY CONTROL MODULE)
DLK-415
< ECU DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
Wiring Diagram - TRUNK LID OPENER SYSTEM -INFOID:0000000001530552
ALKWA0119GB

TRUNK OPEN FUNCTION SYMPTOMS
DLK-425
< SYMPTOM DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
TRUNK OPEN FUNCTION SYMPTOMS
TRUNK LID OPENER SWITCH
TRUNK LID OPENER SWITCH : Symptom TableINFOID:0000000001530563
TRUNK LID OPENER FUNCTION MALFUNCTION
NOTE:
 Before performing the diagnosis in the following table, check “Work Flow”. Refer to DLK-16, "
Work Flow".
 Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
 If the following symptoms are detected, check systems shown in the “Diagnosis/service procedure” column
in this order.
Conditions of Vehicle (Operating Conditions)
 Door lock function is normal.
 Vehicle speed is less than 5 km/h (3 MPH).
 All doors are unlocked.
Symptom Table
Symptom Diagnosis/service procedure Reference page
Trunk lid opener function does not operate by
trunk lid opener switch.1. Check trunk lid opener switch.DLK-101
2. Check vehicle speed signal.DLK-149
3. Check trunk lid opener actuator.DLK-117
4. Check intermittent incident.XX-XX, "*****"
Trunk room lamp switch inoperative. 1. Check trunk room lamp switch.DLK-94

SQUEAK AND RATTLE TROUBLE DIAGNOSES
DLK-433
< SYMPTOM DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
Confirm that the cause of a noise is repaired by test driving the vehicle. Operate the vehicle under the same
conditions as when the noise originally occurred. Refer to the notes on the Diagnostic Worksheet.
Inspection ProcedureINFOID:0000000001396892
Refer to Table of Contents for specific component removal and installation information.
INSTRUMENT PANEL
Most incidents are caused by contact and movement between:
1. Cluster lid A and instrument panel
2. Acrylic lens and combination meter housing
3. Instrument panel to front pillar garnish
4. Instrument panel to windshield
5. Instrument panel mounting pins
6. Wiring harnesses behind the combination meter
7. A/C defroster duct and duct joint
These incidents can usually be located by tapping or moving the components to duplicate the noise or by
pressing on the components while driving to stop the noise. Most of these incidents can be repaired by apply-
ing felt cloth tape or silicon spray (in hard to reach areas). Urethane pads can be used to insulate wiring har-
ness.
CAUTION:
Do not use silicone spray to isolate a squeak or rattle. If you saturate the area with silicone, you will
not be able to recheck the repair.
CENTER CONSOLE
Components to pay attention to include:
1. Shifter assembly cover to finisher
2. A/C control unit and cluster lid C
3. Wiring harnesses behind audio and A/C control unit
The instrument panel repair and isolation procedures also apply to the center console.
DOORS
Pay attention to the:
1. Finisher and inner panel making a slapping noise
2. Inside handle escutcheon to door finisher
3. Wiring harnesses tapping
4. Door striker out of alignment causing a popping noise on starts and stops
Tapping or moving the components or pressing on them while driving to duplicate the conditions can isolate
many of these incidents. You can usually insulate the areas with felt cloth tape or insulator foam blocks to
repair the noise.
TRUNK
Trunk noises are often caused by a loose jack or loose items put into the trunk by the owner.
In addition look for:
1. Trunk lid dumpers out of adjustment
2. Trunk lid striker out of adjustment
3. Trunk lid torsion bars knocking together
4. A loose license plate or bracket
Most of these incidents can be repaired by adjusting, securing or insulating the item(s) or component(s) caus-
ing the noise.
SUNROOF/HEADLINING
Noises in the sunroof/headlining area can often be traced to one of the following:
1. Sunroof lid, rail, linkage or seals making a rattle or light knocking noise
2. Sunvisor shaft shaking in the holder
3. Front or rear windshield touching headlining and squeaking

FUEL FILLER LID OPENER
DLK-457
< REMOVAL AND INSTALLATION >[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
FUEL FILLER LID OPENER
Removal and Installation of Fuel Filler Lid OpenerINFOID:0000000001732025
REMOVAL
1. Remove trunk side finisher (RH). Refer to XX-XX, "*****".
2. Remove fuel filler lid opener cable lock ring.
3. Remove front and rear kicking plates. Refer to XX-XX, "*****"
.
4. Remove rear cushion assembly. Refer to XX-XX, "*****"
.
5. Remove the bolts and the fuel filler lid opener handle.
6. Remove fuel filler lid opener cable clips from the vehicle.
7. Remove the fuel filler lid opener cable (LH drive).
8. Remove the fuel filler lid opener cable (RH drive).
PIIB3831J
LIIA2670E
LIIA2629E
ALKIA0651GB

DLK-466
< REMOVAL AND INSTALLATION >[WITH I-KEY & SUPER LOCK]
TRUNK LID
TRUNK LID
Fitting AdjustmentINFOID:0000000001732031
Longitudinal and lateral clearance adjustment
1. With the striker released, loosen the trunk lid hinge nuts and close the trunk lid.
2. Make the lateral clearance and the clearance to the rear window glass equal. Then open the trunk lid to
tighten the nuts.
Surface height adjustment
1. Loosen the striker bolts. Raise the striker to the top position, and temporarily tighten the upper bolt.
2. Close the trunk lid lightly and adjust the surface height. Then open the trunk lid and tighten the striker
bolts.
Trunk Lid AssemblyINFOID:0000000001732032
REMOVAL
1. Remove the trunk lid finisher. Refer to XX-XX, "*****" .
2. Remove the trunk lid wire harness.
1. Rear fender 2. Trunk lid 3. Rear combination lamp
4. Rear bumper fascia a. 4.0 ± 1.0 mm (0.16 ± 0.04 in) b. 3.5 ± 1.0 mm (0.14 ± 0.04 in)
c. 4.5 ± 1.7 mm (0.03 ± 0.06 in) d. 7.0 ± 2.2 mm (0.28 ± 0.09 in)
LIIA2932E