BR-48
REAR DISC BRAKE
Revision: 2006 November2007 350Z
7. Install the pad retainers and pads to the torque member.
CAUTION:
When attaching the pad retainer, attach it firmly so that it
does not float up higher than the torque member, as shown
in the figure.
8. After assembling shims and shim cover to pad, install it to the
torque member.
9. Install cylinder body. Tighten sliding pin bolts to the specified
torque. Refer to BR-40, "
Components" .
DISC ROTOR INSPECTION
Visual Inspection
Check surface of the disc rotor for uneven wear, cracks, and serious damage. If any non-standard condition is
detected, replace applicable part.
Runout Inspection
1. Using wheel nuts, fix disc rotor to the wheel hub. (2 or more positions)
2. Inspect runout using a dial gauge.
NOTE:
Make sure that wheel bearing axial end play is with in the specification before measuring runout. Refer to
RAX-6, "
On-Vehicle Inspection" .
3. If runout is outside the limit, find the minimum runout point by shifting mounting positions of the disc rotor
and wheel hub by one hole.
4. If runout is still outside the limit after performing the above operation, replace or lathe the disc rotor.
[When lathing, use the Pro–Cut PFM On–Car Brake Lathe (Tool No. 38–PFM90.5) or equivalent.]
Thickness Inspection
Using a micrometer, check thickness of the disc rotor. If thickness is
outside the standard, replace disc rotor.
PFIA0273E
Standard value
(measured at 10 mm (0.39 in) inside the disc edge)
Measurement position:
At a point 10 mm (0.39 in) from outer edge of the disc
Runout limit (with it attached to the vehicle):
0.055 mm (0.0022 in) or less
Runout limit (just the disc rotor):
0.020 mm (0.008 in) or less
BRA0013D
Standard
Standard thickness : 16.0 mm (0.630 in)
Wear limit : 14.0 mm (0.551 in)
Maximum uneven wear (measured at 8 positions)
: 0.015 mm (0.0006 in) or less
SBR020B
BR-50
REAR DISC BRAKE
Revision: 2006 November2007 350Z
2. Apply rubber grease to the piston boot, place it on the piston,
and firmly insert the piston boot cylinder-side lip into the cylinder
body groove.
3. Insert the piston into the cylinder body by hand and firmly attach
the piston boot piston-side lip into the piston groove.
CAUTION:
Press the piston evenly and vary the pressing point to pre-
vent cylinder inner wall from being rubbed.
DISC ROTOR INSPECTION
Visual Inspection
Check surface of the disc rotor for uneven wear, cracks, and serious damage. If any non-standard condition is
detected, replace applicable part.
Runout Inspection
1. Using wheel nuts, fix disc rotor to the wheel hub. (2 or more positions)
2. Inspect runout using a dial gauge.
NOTE:
Make sure that wheel bearing axial end play is with in the speci-
fication before measuring runout. Refer toRAX-6, "
On-Vehicle
Inspection" .
3. If runout is outside the limit, find the minimum runout point by shifting mounting positions of the disc rotor
and wheel hub by one hole.
4. If runout is still outside the limit after performing the above operation, replace or lathe the disc rotor.
[When lathing, use the Pro–Cut PFM On–Car Brake Lathe (Tool No. 38–PFM90.5) or equivalent.]
SFIA1323E
Standard value
(measured at 10 mm (0.39 in) inside the disc edge)
Runout limit (with it attached to the vehicle)
: 0.070 mm (0.0028 in) or less
Runout limit (just for disc rotor)
: 0.040 mm (0.0016 in) or less
BRA0581D
