2007 NISSAN 350Z ECU

BRC-100
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
SIDE G SENSOR
(m/s2 )x–Side G detected by the side G sensor is dis-
played.
STR ANGLE SIG
(°)x–Steering angle detected by the steering angle
sensor is displayed.
PRESS SENSOR
(bar )x–Brake hydraulic pressured detected by the
pressure sensor is displayed.
ENGINE RPM
(rpm)x–The engine speed status determined from the
CAN communication signal is displayed.
SNOW MODE SW
(ON/OFF)––Snow mode switch (ON/OFF) status deter-
mined from the CAN communication signal is
displayed.
BST OPER SIG
(ON/OFF)––Control booster operation signal (ON/OFF) sta-
tus determined from the CAN communication
signal is displayed.
M - MODE SIG
(ON/OFF)–– M mode (ON/OFF) status determined from the
CAN communication signal is displayed.
OD OFF SW
(ON/OFF)––OD cancel switch (ON/OFF) status determined
from the CAN communication signal is dis-
played.
EBD SIGNAL
(ON/OFF)– – EBD operation (ON/OFF) status is displayed.
ABS SIGNAL
(ON/OFF)– – ABS operation (ON/OFF) status is displayed.
TCS SIGNAL
(ON/OFF)– – TCS operation (ON/OFF) status is displayed.
VDC SIGNAL
(ON/OFF)– – VDC operation (ON/OFF) status is displayed.
EBD FAIL SIG
(ON/OFF)––EBD fail-safe signal (ON/OFF) status is dis-
played.
ABS FAIL SIG
(ON/OFF)––ABS fail-safe signal (ON/OFF) status is dis-
played.
TCS FAIL SIG
(ON/OFF)––TCS fail-safe signal (ON/OFF) status is dis-
played.
VDC FAIL SIG
(ON/OFF)––The VDC fail-safe signal (ON/OFF) status is
displayed.
CRANKING SIG
(ON/OFF)––Ignition switch START position signal input sta-
tus is displayed.
ASCD SIGNAL
(ON/OFF)– – ASCD (ON/OFF) status is displayed.
FLUID LEV
(ON/OFF)x–Brake fluid level sensor (ON/OFF) status is dis-
played.
PARKING BRAKE SW
(ON/OFF)x–Parking brake switch (ON/OFF) status is dis-
played.
USV FL-RR
(ON/OFF)––Primary side USV solenoid valve (ON/OFF)
status is displayed.
USV FR-RL
(ON/OFF)––Secondary side USV solenoid valve (ON/OFF)
status is displayed.
HSV FL-RR
(ON/OFF)––Primary side HSV solenoid valve (ON/OFF)
status is displayed.
HSV FR-RL
(ON/OFF)––Secondary side HSV solenoid valve (ON/OFF)
status is displayed. Item (Unit)SELECT MONITOR ITEM
Remarks
ECU INPUT
SIGNALSMAIN
SIGNALSSELECTION
FROM MENU

TROUBLE DIAGNOSIS
BRC-101
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: 2006 November2007 350Z
Active TestNFS000IP
CAUTION:

Do not perform active test while driving.

Make sure to completely bleed air from the brake system.

The ABS and brake warning lamps turn on during the active test.
NOTE:

When the active test is conducted while depressing the pedal, the pedal depression amount will change,
but this is normal.

Approximately 10 seconds after the operation is begun, “TEST STOP” will be displayed.
TEST ITEM
Solenoid valve
CAUTION:
The example shown is for the front right wheel. The procedure for the other wheels is the same as
given below.

When conducting an active test of the ABS function, select the main item for each test item. In addition,
when conducting an active test of the VDC/TCS function, select the item menu for each test item.

For the ABS solenoid valve, touch “UP”, “KEEP”, “DOWN” on the display screen. For the ABS solenoid
valve (ACT), touch “UP”, “ACT UP”, “ACT KEEP” and confirm that the solenoid valves (IN, OUT, USV,
HSV) operate as shown in the table below.
*: ON for 1 to 2 seconds after the touch, and then OFF
ABS Motor
Touch “ON”, “OFF” on the display screen and make sure the ABS motor relay is operating as shown in the
table below.
Correct and Quick DiagnosisNFS0004B
DIAGNOSIS PRECAUTIONS

Before performing the trouble diagnosis, always read the general information (GI) to confirm the general
precautions. Refer to GI-3, "
General Precautions" .

When replacing steering angle sensor, steering system components or suspension system components,
and when adjusting the alignment, be sure to adjust the steering angle sensor neutral position before driv-
ing. Refer to BRC-79, "
Adjustment of Steering Angle Sensor Neutral Position" .

After completing service, always erase the self-diagnosis results. Refer to BRC-96, "HOW TO ERASE
SELF-DIAGNOSIS RESULTS" .
V/R OUTPUT
(ON/OFF)––Valve relay operation signal (ON/OFF) status is
displayed.
M/R OUTPUT
(ON/OFF)––Monitor relay operation signal (ON/OFF) status
is displayed. Item (Unit)SELECT MONITOR ITEM
Remarks
ECU INPUT
SIGNALSMAIN
SIGNALSSELECTION
FROM MENU
OperationABS solenoid valve ABS solenoid valve (ACT)
UP KEEP DOWN UP ACT UP ACT KEEP
FR RH IN SOL OFF ON ON OFF OFF OFF
FR RH OUT SOL OFF OFF ON* OFF OFF OFF
USV [FR - RL] OFF OFF OFF OFF ON ON
HSV [FR - RR] OFF OFF OFF OFF ON* OFF
Operation ON OFF
MOTOR RELAY ON OFF
ACTUATOR RLY ON ON

BRC-108
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS FOR SYSTEM
Revision: 2006 November2007 350Z
Pressure Sensor SystemNFS0004G
INSPECTION PROCEDURE
1. CHECK SELF-DIAGNOSIS RESULTS
Check self-diagnosis results.
Is the above displayed in the self-diagnosis display items?
YES >> GO TO 2.
NO >> INSPECTION END
2. CHECK STOP LAMP SWITCH CONNECTOR
1. Disconnect stop lamp switch connector and VDC/TCS/ABS control unit connector and check the termi-
nals for deformation, disconnection, looseness, and so on. If there is an error, repair or replace the termi-
nal.
2. Securely reconnect the connectors.
3. Start engine.
4. Repeat pumping brake pedal carefully several times, then perform self-diagnosis again.
Is the result of self-diagnosis normal?
YES >> The connector terminal contact is loose, damaged, open or shorted.
NO >> GO TO 3.
3. CHECK STOP LAMP SWITCH
1. Turn ignition switch OFF and disconnect stop lamp switch con-
nector E111.
2. Disconnect stop lamp switch connector
3. Check continuity between stop lamp switch connector terminal 3
and 4.
OK or NG
OK >> GO TO 4.
NG >> Replace stop lamp switch. Refer to BR-8, "
Components" .
Self-diagnosis results
PRESS SEN CIRCUIT
Stop lamp switch Condition Continuity
3 – 4Release stop lamp switch
(When brake pedal is depressed.)Ye s
Push stop lamp switch
(When brake pedal is released.)No
SFIA3390E

TROUBLE DIAGNOSIS FOR SYSTEM
BRC-113
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: 2006 November2007 350Z
Solenoid and VDC Change-Over Valve SystemNFS0004J
INSPECTION PROCEDURE
1. CHECK SELF-DIAGNOSIS RESULTS
Check self-diagnosis results.
Is the above displayed in the self-diagnosis display items?
YES >> GO TO 2.
NO >> INSPECTION END
2. CHECK CONNECTOR
1. Disconnect VDC/TCS/ABS control unit connector and solenoid connector E49, E50 and check the termi-
nals for deformation, disconnection, looseness, and so on. If there is an error, repair or replace the termi-
nal.
2. Securely reconnect the connectors and then preform self-diagnosis.
Is the result of self-diagnosis normal?
YES >> The connector terminal contact is loose, damaged, open or shorted.
NO >> GO TO 3.
Self-diagnosis results
IN ABS SOL
OUT ABS SOL
USV LINE [FL-RR]
USV LINE [FR-RL]
HSV LINE [FL-RR]
HSV LINE [FR-RL]

BRC-116
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS FOR SYSTEM
Revision: 2006 November2007 350Z
ABS Motor and Motor Relay SystemNFS0004K
INSPECTION PROCEDURE
1. CHECK SELF-DIAGNOSIS RESULTS
Check self-diagnosis results.
Is the above displayed in the self-diagnosis display items?
YES >> GO TO 2.
NO >> INSPECTION END
2. CHECK CONNECTOR
1. Disconnect VDC relay box connector E47, E48, E222 and VDC/TCS/ABS control unit connector and
check the terminals for deformation, disconnection, looseness, and so on. If there is an error, repair or
replace the terminal.
2. Securely reconnect the connectors and then preform self-diagnosis.
Is the result of self-diagnosis normal?
YES >> The connector terminal contact is loose, damaged, open or shorted.
NO >> GO TO 3.
3. CHECK ABS MOTOR AND MOTOR RELAY POWER SYSTEM
1. Disconnect VDC relay box connectors E48.
2. Check voltage between VDC relay box connector and ground.
OK or NG
OK >> GO TO 4.
NG >> The circuit between battery and VDC relay box terminal
10 is open or shorted. Repair the circuit.
Self-diagnosis results
PUMP MOTOR
VDC relay box Ground Voltage
10 — Battery voltage (Approx. 12 V)
SFIA1892E

BRC-118
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS FOR SYSTEM
Revision: 2006 November2007 350Z
Actuator Relay SystemNFS0004L
INSPECTION PROCEDURE
1. CHECK SELF-DIAGNOSIS RESULTS
Check self-diagnosis results.
Is the above displayed in the self-diagnosis display items?
YES >> GO TO 2.
NO >> INSPECTION END
2. CHECK CONNECTOR
1. Disconnect VDC relay box connector E47, E48, E222 and VDC/TCS/ABS control unit connector B114 and
check terminals for deformation, disconnection, looseness, and so on. If there is an error, repair or replace
the terminal.
2. Securely reconnect the connectors and then preform self-diagnosis.
Is the result of self-diagnosis normal?
YES >> The connector terminal contact is loose, damaged, open or shorted.
NO >> GO TO 3.
3. CHECK ACTUATOR RELAY POWER SYSTEM
1. Turn ignition switch OFF and disconnect VDC relay box connec-
tor E48.
2. Check voltage between VDC relay box connector and ground.
OK or NG
OK >> GO TO 4.
NG >> The circuit between battery and VDC relay box harness
connector E48 terminal 9 is open or shorted. Repair the
circuit.
4. CHECK ACTUATOR RELAY HARNESS
1. Disconnect VDC/TCS/ABS control unit connector B114.
2. Check continuity between VDC/TCS/ABS control unit connector
and VDC relay box connector E47.
OK or NG
OK >> GO TO 5.
NG >> Open or short in harness. Repair or replace the harness.
5. CHECK ACTUATOR RELAY
Independently check VDC actuator relay. Refer to BRC-123, "
ABS MOTOR RELAY AND ACTUATOR RELAY"
.
OK or NG
OK >> Replace VDC actuator assembly.
NG >> Replace VDC relay box.
Self-diagnosis results
MAIN RELAY
VDC relay box Ground Voltage
9 — Battery voltage (Approx. 12 V)
SFIA1894E
VDC/TCS/ABS control unit VDC relay box Continuity
25
Ye s
36 7
SFIA1895E

TROUBLE DIAGNOSIS FOR SYSTEM
BRC-119
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: 2006 November2007 350Z
Stop Lamp Switch SystemNFS0004M
INSPECTION PROCEDURE
1. CHECK SELF-DIAGNOSIS RESULTS
Check self-diagnosis results.
Is the above displayed in the self-diagnosis display items?
YES >> GO TO 2.
NO >> INSPECTION END
2. CHECK CONNECTOR
1. Disconnect stop lamp switch connector and VDC/TCS/ABS control unit connector and check the termi-
nals for deformation, disconnection, looseness, and so on. If there is an error, repair or replace the termi-
nal.
2. Securely reconnect the connectors.
3. Start engine.
4. Repeat pumping brake pedal carefully several times, then perform self-diagnosis again.
Is the result of self-diagnosis normal?
YES >> The connector terminal contact is loose, damaged, open or shorted.
NO >> GO TO 3.
3. CHECK STOP LAMP SWITCH
1. Turn ignition switch OFF and disconnect stop lamp switch con-
nector E111.
2. Disconnect stop lamp switch connector
3. Check continuity between stop lamp switch connector terminal 3
and 4.
OK or NG
OK >> GO TO 4.
NG >> Replace stop lamp switch. Refer to BR-8, "
Components" .
Self-diagnosis results
STOP LAMP SW
Stop lamp switch Condition Continuity
3 – 4Release stop lamp switch
(When brake pedal is depressed.)Ye s
Push stop lamp switch
(When brake pedal is released.)No
SFIA3390E

BRC-120
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS FOR SYSTEM
Revision: 2006 November2007 350Z
4. CHECK STOP LAMP SWITCH CIRCUIT
1. Turn ignition switch OFF and disconnect VDC/TCS/ABS control
unit connector B114.
2. Check voltage between VDC/TCS/ABS control unit connector
B114 terminal 48 and ground.
OK or NG
OK >> Connect the connectors and conduct a VDC/TCS/ABS control unit self-diagnosis.
NG >> Open or short in harness. Repair or replace the harness.
VDC/TCS/ABS Control Unit Power and Ground SystemsNFS0004N
INSPECTION PROCEDURE
1. CHECK SELF-DIAGNOSIS RESULTS
Check self-diagnosis results.
Is the above displayed in the self-diagnosis item?
YES >> GO TO 2.
NO >> INSPECTION END
2. CHECK CONNECTOR
1. Disconnect VDC/TCS/ABS control unit connector and check the terminal for deformation, disconnection,
looseness, and so on. If there is an error, repair or replace the terminal.
2. Securely reconnect the connector and then perform self-diagnosis.
Is the result of self-diagnosis normal?
YES >> The connector terminal contact is loose, damaged, open or shorted.
NO >> GO TO 3.
SFIA1896E
VDC/TCS/ABS control unit Ground Measurement condition Voltage
48 —Brake pedal depressed.Battery voltage
(Approx. 12 V)
Brake pedal not depressed. Approx. 0 V
Self-diagnosis results
BATTERY VOLTAGE [ABNORMAL]