2007 NISSAN 350Z ignition

AV-36
AUDIO
Revision: 2006 November2007 350Z
34 (L) 33 (P) Audio signal rear RH Input ON Receive audio signal
36 (L/G) 35 (L/Y) Audio signal rear LH Input ON Receive audio signal
38 (G) 37 (R) Audio signal front RH Input ON Receive audio signal
40 (LG) 39 (PU) Audio signal front LH Input ON Receive audio signal
41 (G/Y) GroundBOSE speaker amp.
ON signalInput ON — Approx. 12 V Te r m i n a l
(Wire color)
ItemSignal
input/
outputCondition
Reference value
+–Ignition
switchOperation
SKIB3609E
SKIB3609E
SKIB3609E
SKIB3609E

AUDIO
AV-37
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 November2007 350Z
Terminals and Reference Value for Woofer Amp.NKS002BC
Terminal
(Wire color)
ItemSignal
input/
outputCondition
Reference value
+–Ignition
switchOperation
2 (W) 1 (OR) Audio signal woofer Input ONReceive audio signal
4 (L) 3 (Y) Audio signal woofer Output ON Receive audio signal
6 (G/R) GroundWoofer amp. ON
signalInput ON — Approx. 12 V
7 (B) Ground Ground — ON — Approx. 0 V
8 (G) Ground Battery power supply Input OFF — Battery voltage
SKIB3609E
SKIB3609E

AV-38
AUDIO
Revision: 2006 November2007 350Z
Terminals and Reference Value for Satellite Radio TunerNKS002EC
Te r m i n a l
(Wire color)
ItemSignal
input/
outputCondition
Reference value
+–Ignition
switchOperation
22 (R) 21 (G)Satellite radio audio
signal LHOutput ONReceive satellite radio audio
signal
24 (B) 23 (W)Satellite radio audio
signal RHOutput ONReceive satellite radio audio
signal
25 — Shield — — — —
26 — Shield — — — —
28 (L) GroundCommunication signal
REQ (SAT-AUDIO)Output ONWhen setting to satellite
radio mode
29 (OR/L) GroundCommunication signal
Tx (SAT-AUDIO)Output ONWhen setting to satellite
radio mode
30 (W/L) GroundCommunication signal
Rx (AUDIO-SAT)Input ONWhen setting to satellite
radio mode
32 (BR/Y) Ground Battery power supply Input OFF — Battery voltage
36 (P/B) Ground ACC power supply Input ACC — Battery voltage
40 — Satellite radio antenna — — — —
SKIB3609E
SKIB3609E
SKIB7338E
SKIB7337E
SKIB7336E

AUDIO
AV-39
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 November2007 350Z
Trouble DiagnosisNKS002ED

The majority of the audio malfunctions are the result of outside causes (bad CD, electromagnetic interfer-
ence, etc.). Check the symptoms below to diagnose the malfunction.

The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunction-
ing. Check if noise is caused and/or changed by engine speed, ignition switch turned to each position, and
operation of each piece of electrical equipment, and then determine the cause.

Refer to "SERVICE BULLETIN NTB04-119" for the diagnosis of satellite radio.
NOTE:
Noise resulting from variations in field strength, such as fading noise and multi-path noise, or external noise
from trains and other sources. It is not a malfunction.

Fading noise: This noise occurs because of variations in the field strength in a narrow range due to moun-
tains or buildings blocking the signal.
Symptom Possible malfunction location
Audio system does not work properly.

Audio unit power supply circuit

Audio unit
No sound can be heard from all speakers.
Base system

Audio unit
BOSE system

BOSE speaker amp. power supply and ground circuit

BOSE speaker amp. ON signal circuit

Audio unit

BOSE speaker amp.
No sound can be heard from one or several speakers.
Base system

Audio signal circuit between audio unit and speaker

Speaker

Tweeter

Audio unit
BOSE system

Audio signal circuit between audio unit and BOSE speaker amp.

Audio signal circuit between BOSE speaker amp. and speaker

Speaker

Tweeter

Audio unit

BOSE speaker amp.
No sound can be heard from woofer.

Woofer amp. power supply and ground circuit

Woofer amp. ON signal circuit

Audio signal circuit between BOSE speaker amp. and woofer

Audio signal circuit between woofer amp. and woofer

Woofer

Woofer amp.

BOSE speaker amp.
No sound can be heard from radio or noise is caught.

Antenna amp. ON signal circuit

Antenna feeder

Antenna

Antenna amp.

Audio unit
None of the steering switch operations work

TEL adapter unit control signal 1 circuit

Steering switch signal ground circuit

AUDIO
AV-41
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 November2007 350Z
Power Supply Circuit InspectionNKS002BF
1. CHECK FUSE
Make sure that the following fuses of the audio unit, BOSE speaker amp. and woofer amp. are not blown.
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-
4, "POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Check voltage between audio unit harness connector terminals
and ground.
2. Check voltage between BOSE speaker amp., woofer amp. har-
ness connector terminals and ground (BOSE system).
OK or NG
OK >>
INSPECTION END (Base system)

GO TO 3 (BOSE system).
NG >> Repair harness or connector.
Unit Signal Fuse No.
Audio unitBattery power supply 37
Ignition switch ACC or ON 6
BOSE speaker amp. Battery power supply 37
Woofer amp. Battery power supply 17
UnitTerminals
OFF ACC ON (+)
(–)
Connector Terminal
Audio
unitM406GroundBattery
voltageBattery
voltageBattery
voltage
10 Ground 0 VBattery
voltageBattery
voltage
SKIA8743E
UnitTerminals
OFF ACC ON (+)
(–)
Connector Terminal
BOSE
speaker
amp.T6 11
GroundBattery
voltageBattery
voltageBattery
voltage
Woofer
amp.B32 8
SKIA8744E

AV-42
AUDIO
Revision: 2006 November2007 350Z
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BOSE speaker amp. and woofer amp. connectors.
3. Check continuity between BOSE speaker amp. harness connec-
tor T6 terminal 27 and ground.
4. Check continuity between woofer amp. harness connector B32
terminal 7 and ground.
OK or NG
OK >> INSPECTION END
NG >> Repair harness or connector.
Steering Switch Does Not OperateNKS002EE
1. CHECK STEERING SWITCH RESISTANCE
1. Turn ignition switch OFF.
2. Disconnect combination switch (spiral cable) connector.
3. Check resistance between steering switch harness connector
M203 terminals.
OK or NG
OK >> GO TO 2.
NG >> Replace steering switch.
2. CHECK SPIRAL CABLE
1. Disconnect combination switch (spiral cable) connector.
2. Check continuity between combination switch (spiral cable) con-
nector (A) terminals 16, 17, 20 and connector (B) terminals 32,
31, 24.
OK or NG
OK >> GO TO 3.
NG >> Replace spiral cable.27 – Ground : Continuity should exist.
7 – Ground : Continuity should exist.
SKIA8745E
Terminal Signal name Condition Resistance (Ω)
16
17Power Press and hold POWER switch. Approx. 0
Seek downPress and hold SEEK DOWN
switch.Approx. 165
Vo l u m e d o wnPress and hold VOLUME DOWN
switch.Approx. 652
20Mode Press and hold MODE switch. Approx. 0
Seek up Press and hold SEEK UP switch. Approx. 165
Vo l u m e u pPress and hold VOLUME UP
switch.Approx. 652
SKIB7339E
16 – 32 : Continuity should exist.
17 – 31 : Continuity should exist.
20 – 24 : Continuity should exist.
SKIB7340E

AV-44
AUDIO
Revision: 2006 November2007 350Z
AudioPilot® Does Not WorkNKS002BG
1. CHECK AUDIO UNIT
Check AudioPilot
® turns ON.
OK or NG
OK >> GO TO 2.
NG >> Turn AudioPilot® ON.
2. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect audio unit and BOSE speaker amp. connectors.
3. Check continuity between audio unit harness connector M39 ter-
minal 17 and BOSE speaker amp. harness connector T7 termi-
nal 31.
4. Check continuity between audio unit harness connector M39 ter-
minal 17 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK AUDIOPILOT® SIGNAL
1. Connect audio unit and BOSE speaker amp. connectors.
2. Turn ignition switch ON.
3. Check voltage between audio unit harness connector terminals
and ground.
OK or NG
OK >> GO TO 4.
NG >> Replace audio unit.17 – 31 : Continuity should exist.
17 – Ground : Continuity should not exist.
SKIA8019E
Te r m i n a l s
Condition Voltage (+)
(–)
Connector Terminal
M39 17 GroundAudioPilot
® OFFApprox. 7.5 V
AudioPilot
® ONApprox. 0 V
SKIA8020E

AUDIO
AV-45
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 November2007 350Z
4. CHECK HARNESS
1. Turn ignition switch OFF
2. Disconnect BOSE speaker amp. and microphone connectors.
3. Check continuity between BOSE speaker amp. harness connec-
tor T7 terminal 17 and microphone harness connector E123 ter-
minal 1.
4. Check continuity between BOSE speaker amp. harness connec-
tor T7 terminal 17 and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector.
5. CHECK HARNESS
1. Check continuity between BOSE speaker amp. harness connec-
tor T7 terminal 18 and microphone harness connector E123 ter-
minal 2.
2. Check continuity between BOSE speaker amp. harness connec-
tor T7 terminal 18 and ground.
OK or NG
OK >> GO TO 6.
NG >> Repair harness or connector.
6. CHECK MICROPHONE SIGNAL
1. Connect BOSE speaker amp. and microphone connectors.
2. Turn ignition switch ON.
3. Check voltage waveform between BOSE speaker amp. harness
connector T7 terminal 17 and 18 using oscilloscope, when input-
ting some sounds (voice, etc.) toward the microphone.
Does the voltage waveform change with sounds?
YES >> Replace BOSE speaker amp.
NO >> Replace microphone.17 – 1 : Continuity should exist.
17 – Ground : Continuity should not exist.
SKIA3105E
18 – 2 : Continuity should exist.
18 – Ground : Continuity should not exist.
SKIA3106E
17 – 18:
SKIA3104EPKIA2104E