2007 MITSUBISHI LANCER EVOLUTION speedometer

MPI -Troubleshooting13A-43
Code No. P0500 Vehicle speed sensor systemProbable cause
Inspection Range
DIgnition switch: ON
DAfter 2 seconds from setting ignition switch to ON position or completion of engine
starting
DThe engine speed is approximately 2,000 - 4,000 r/min or more.
DThe volumetric efficiency is 60 - 80%.
Evaluation Conditions
DVehicle speed signal does not change for 2 seconds. (Pulse signal is not input.)DVehicle speed sensor malfunction
DVehicle speed sensor circuit disconnection,
short-circuit, or connector contact defect
DEngine-ECU malfunction
NG
Replace the engine-ECU.
OK
Check the trouble symptoms.OKIntermittent malfunction
(Refer to GROUP 00 - Points to Note
for Intermittent Malfunctions.)
NG
Check the following connectors:
B-03, C-115
NG
Replace the engine-ECU.
OK
Check the trouble symptoms.
YES
Measure at the C-115 engine-ECU
connector.
DConnect the connector.
DVoltage between terminal No. 86
and earth
(Ignition switch: ON)
OK:When vehicle is pushed and
moved, repeatedly varies
between 0 and 5 V.OKCheck the following connector:
C-115NG
Repair
Is speedometer normal?NOCheck the vehicle speed sensor.
(Refer to GROUP 54 - Combination
Meter.)
NG
Repair

22B-1
MANUAL
TRANSMISSION
OVERHAUL
CONTENTS
GENERAL DESCRIPTION 2...................
SPECIFICATIONS 6..........................
SERVICE SPECIFICATIONS 6.................
SEALANTS 7................................
LUBRICANTS 8..............................
SNAP RINGS, SPACERS AND THRUST
PLATES FOR ADJUSTMENT 9................
TIGHTENING TORQUE 11....................
SPECIAL TOOLS 12..........................
TRANSMISSION 15...........................
INPUT SHAFT 22............................OUTPUT SHAFT 29..........................
REVERSE IDLER GEAR 37...................
SPEEDOMETER GEAR 38....................
SELECT LEVER 39...........................
CONTROL HOUSING 40......................
CLUTCH HOUSING 43........................
TRANSMISSION CASE 46....................
CENTER DIFFERENTIAL 48..................
TRANSFER 51...............................

MANUAL TRANSMISSION OVERHAUL -Specifications/Service Specifications22B-6
SPECIFICATIONS
TRANSMISSION MODEL TABLE
Transmission
modelGear ratioSpeedometer
gear ratioFinal
reduction
ratioFront LSDVehicle modelEngine model
W5M51 - 2 - X5BA28/364.529CT9A4G63 - I/C•T/C
W5M51 - 2 - X5B1B28/364.529Not providedCT9A4G63 - I/C •T/C
W5M51 - 2 - X5B2C28/364.529ProvidedCT9A4G63 - I/C •T/C
W5M51 - 2 - X5B3B28/364.529Not providedCT9A4G63 - I/C •T/C
W5M51 - 2 - X5B4C28/364.529ProvidedCT9A4G63 - I/C •T/C
GEAR RATIO TABLE
ABC
1st2.9282.785←
2nd1.950←←
3rd1.407←1.444
4th1.031←1.096
5th0.720←0.825
Reverse3.416←←
Transfer gear ratio0.3018←←
SERVICE SPECIFICATIONS
ItemsStandard value mmLimit value mm
Input shaft end play0.05 loose to 0.17 loose-
Input shaft front bearing end play0.01 tight to 0.12 loose-
Input shaft rear bearing end play0.01 tight to 0.12 loose-
Input shaft 5th speed gear end play0.01 tight to 0.09 loose-
Output shaft preload0.13 tight to 0.18 tight-
Output shaft bearing end play0.01 tight to 0.09 loose-
Output shaft 3rd speed gear end play0.01 tight to 0.09 loose-
Center differential case preload0.05 tight to 0.11 tight-
Center differential case pinion backlash0.025 - 0.150-
Clearance between synchronizer ring rear surface and gears-0.5
Provided

MANUAL TRANSMISSION OVERHAUL -Tightening Torque22B-11
TIGHTENING TORQUE
TRANSMISSION
ItemsTightening torque N•m
Under cover mounting bolt6.9±1
Interlock plate bolt30±3
Clutch housing and transmission case tightening bolt44±5
Clutch release bearing retainer mounting bolt9.8±2
Control housing mounting bolt18±3
Shift cable bracket mounting bolt18±3
Speedometer gear mounting bolt3.9±1
Stopper bracket mounting bolt18±3
Select lever mounting bolt18±3
Select lever mounting nut11±1
Center differential drive gear mounting bolt132±5
Backup light switch32±2
Poppet spring32±2
Reverse idler gear shaft mounting bolt48±5
Roll stopper bracket mounting bolt69±9
TRANSFER
ItemsTightening torque N•m
Transfer cover mounting bolt23±3
Transmission and transfer tightening bolt69±9

MANUAL TRANSMISSION OVERHAUL -Transmission22B-15
TRANSMISSION
DISASSEMBLY AND REASSEMBLY
3
69±9N•m18±3N•m
69±9N•m18±3N•m
69±9N•m 32±2N•m
32±2N•m
3.9±1N•m
6
2
37
8 59
110
4
Disassembly steps
1. Transfer
2. O-ring
3. Roll stopper bracket
4. Shift cable bracket
5. Select lever"JA6. Speedometer gear
7. Backup light switch
8. Gasket
"IA9. Poppet spring
"HA10. Gasket

MANUAL TRANSMISSION OVERHAUL -Transmission22B-21
"GACONTROL HOUSING INSTALLATION
Apply sealant at the positions of the transmission case shown
in the illustration.
Sealant
Specified sealant:
MITSUBISHI genuine sealant Part No.MD997740 or
equivalent
Caution
Evenly squeeze out the agent so that it is not insufficient
or excessive.
"HASPEEDOMETER GEAR INSTALLATION
Apply transmission oil on the O-ring for the speedometer
gear.
Transmission oil
Specified oil:
MITSUBISHI genuine “DIA-QUEEN” multi gear oil
<75W/85W> or equivalent
"IASELECT LEVER INSTALLATION
Apply grease on the sliding section of the select lever shoe’s
control shaft.
Grease
Specified grease:
MITSUBISHI genuine grease Part No.0101011 or
equivalent
"JAO-RING INSTALLATION
Apply transmission oil on the O-ring.
Transmission oil
Specified oil:
MITSUBISHI genuine “DIA-QUEEN” multi gear oil
<75W/85W> or equivalent
INSPECTION
BACKUP LIGHT SWITCH
Check the continuity between the terminals.
ItemsContinuity
Switch pressedContinuity not established
Switch releasedContinuity established
Control shaft
Select
lever
shoe

MANUAL TRANSMISSION OVERHAUL -Speedometer Gear22B-38
SPEEDOMETER GEAR
DISASSEMBLY AND REASSEMBLY
Apply gear oil on
all sliding sections
before installing.
34
2
1
Disassembly steps
1. e-clip
2. Speedometer driven gear
3. O-ring
4. Sleeve

MANUAL TRANSMISSION OVERHAUL -Center Differential22B-48
CENTER DIFFERENTIAL
DISASSEMBLY AND REASSEMBLY
Apply gear oil on
all sliding sections
before installing.
161310 7
11
8 9653
41
2
17
12
1514
912 121112
132±5N•m
Disassembly steps
"DA1. Center differential drive gear
"CA2. Center differential flange
AA""BA3. Taper roller bearing
"CA4. Snap ring
"CA5. Front output shaft
"CA6. Spacer
"CA7. Side gear
"CA8. Lock pin
"CA9. Pinion shaft"CA10. Pinion shaft holder
"CA11. Pinion
"CA12. Washer
"CA13. Side gear
"CA14. Spacer
AB""AA15. Taper roller bearing
16. Speedometer drive gear
17. Differential case
DISASSEMBLY SERVICE POINTS
AA"TAPER ROLLER BEARING REMOVAL
Using the special tool, remove the taper roller bearing from
the center differential flange.MD998917