2007 MITSUBISHI LANCER EVOLUTION sensor

ENGINE OVERHAUL -Timing Belt11B-13
TIMING BELT
REMOVAL AND INSTALLATION
1
11±1N•m
2
3
4 56
7
8
910
11 1213
14 15
16 1718
192021 2223
2425
26
27
2829
30
313233
34
35
49±6N•m
21±4N•m
23±3N•m
11±1N•m11±1N•m
88±10 N•m
35±6N•m
54±5N•m 19±3N•m 46±3N•m 9±1N•m162±5N•m3.5±0.5 N•m
49±9N•m
8.8±1.0 N•m 49±5N•m
Removal steps
1. Timing belt front upper cover
2. Timing belt front center cover
3. Timing belt front lower cover
4. Power steering pump bracket
AA""MA5. Timing belt
"LA6. Tensioner pulley
7. Tensioner arm
"KA8. Auto tensioner
9. Idler pulley
10. Crank angle sensor
AB""JA11. Oil pump sprocket
AC""IA12. Crankshaft bolt
AD""IA13. Crankshaft sprocket
"IA14. Crankshaft sensing blade
15. Tensioner B
AE""HA16. Timing belt B
AF""GA17. Counter balance shaft sprocket
"FA18. SpacerAG""EA19. Crankshaft sprocket B
20. Crankshaft key
21. Breather hose
22. PCV hose
23. PCV valve
24. PCV valve gasket
25. Oil filler cap
"DA26. Rocker cover
"DA27. Rocker cover gasket A
28. Rocker cover gasket B
"CA29. Semi-circular packing
"BA30. Engine support bracket
AH""AA31. Camshaft sprocket bolt
32. Camshaft sprocket
33. Timing belt rear right cover
34. Timing belt rear left upper cover
35. Timing belt rear left lower cover

ENGINE OVERHAUL -Secondary Air System and Intake Manifold11B-28
SECONDARY AIR SYSTEM AND INTAKE MANIFOLD
REMOVAL AND INSTALLATION
1
11±1N•m
23 4 5
6
7
8
9
10 1112
13
11±1N•m24±3N•m
14±1N•m
31±3N•m5±1N•m
20±2N•m
22±4N•m
36±6N•m23±4N•m
14±1N•m
36±6N•m
36±6N•m22±4N•m
49±5N•m
Removal steps
1. Exhaust manifold heat protector
2. Vacuum hose and pipe
"DA3. Air pipe assembly
4. Air control valve gasket
5. Air control valve assembly
6. Engine hanger
"CA7. Air control valve bracket"BA8. Manifold differential pressure (MDP)
sensor
9. O-ring
"AA10. Intake manifold stay
11. Alternator brace stay
12. Intake manifold
13. Intake manifold gasket

ENGINE OVERHAUL -Secondary Air System and Intake Manifold11B-29
INSTALLATION SERVICE POINTS
"AAINTAKE MANIFOLD STAY INSTALLATION
Check that the intake manifold stay is seated against the
intake manifold and cylinder block boss, and then tighten
at the specified torque 31±3N•m.
"BAMANIFOLD DIFFERENTIAL PRESSURE (MDP)
SENSOR INSTALLATION
Caution
Make sure not to apply impact against the sensor when
installing.
Do not use a sensor that has been dropped.
"CAAIR CONTROL VALVE BRACKET INSTALLATION
1. Temporarily tighten the air control valve bracket and
engine hanger with the bolt for tightening with the intake
manifold.
2. Tighten the bolt 1 shown in the illustration at the specified
torque 23±4N•m.
3. Tighten the bolt 2 shown in the illustration at the specified
torque 36±6N•m.
4. Tighten the bolt 3 shown in the illustration with the engine
hanger at the specified torque 22±4N•m.
"DAAIR PIPE ASSEMBLY INSTALLATION
1. Temporarily tighten air pipe assembly onto the air control
valve.
2. Tighten the bolts 1 and 2 shown in the illustration to
the exhaust manifold at the specified torque 49±5N•m.
3. Tighten the bolt 3 shown in the illustration to the air control
valve at the specified torque 24±3N•m.
4. Tighten the bolt 4 shown in the illustration to the cam
position sensor support at the specified toque 11±1
N•m.
5. Tighten the bolt 5 shown in the illustration to the exhaust
manifold at the specified torque 14±1N•m.
Intake manifold stay
1
23
1
5
23
4

ENGINE OVERHAUL -Exhaust Manifold11B-30
EXHAUST MANIFOLD
REMOVAL AND INSTALLATION
1
17±2N•m
2 3
45
6
78
910
11 1213
11±1N•m
14±1N•m 59±5N•m
9±1N•m 10±1N•m 44±5N•m
31±2N•m
42±7N•m 10±1N•m
55±10 N•m59±5N•m
19±1N•m 14±1N•m
42±7N•m
19±3N•m18 19
14
15
16
17
33±6N•m
47±6N•m
Removal steps
1. Engine hanger
2. Turbocharger heat protector
3. Oxygen sensor
4. Exhaust fitting bracket
5. Exhaust fitting
6. Exhaust fitting gasket
7. Air outlet fitting
"CA8. Air outlet fitting gasket
9. Oil return pipe
10. Oil return pipe gasket"BA11. Oil return pipe gasket
12. Turbocharger assembly and pipe
assembly
13. Turbocharger gasket
14. Oil pipe
15. Water pipe B
16. Water pipe A
17. Turbocharger assembly
"AA18. Exhaust manifold
19. Exhaust manifold gasket

ENGINE OVERHAUL -Water Pump and Water Hose11B-32
WATER PUMP AND WATER HOSE
REMOVAL AND INSTALLATION
1
2
3
45
67
8
9
10 11
12
13
10±1N•m
14±1N•m 23±2N•m10±1N•m
13±2N•m10.8±1.0 N•m
29±10 N•m
1415 16
23±4N•m
23±4N•m
Removal steps
1. Water hose
2. Water hose
3. Water hose
4. Water hose
"DA5. Engine coolant temperature sensor
"CA6. Engine coolant temperature gauge
unit
"BA7. Water outlet fitting
8. Thermostat9. Thermostat housing
10. Gasket
"AA11. O-ring
"AA12. Water inlet pipe
"AA13. O-ring
14. Water pump
15. Water pump gasket
16. Knock sensor

ENGINE OVERHAUL -Water Pump and Water Hose11B-33
INSTALLATION SERVICE POINTS
"AAO-RING/WATER INLET PIPE INSTALLATION
Replace the O-ring for the water inlet pipe with a new part,
and apply water on the periphery of the O-ring so that it
can be inserted easily into the water pump and thermostat
housing.
Caution
(1) Never apply grease or oil, such as engine oil, on the
O-ring.
(2) Install the water inlet pipe onto the thermostat
housing, and then fix.
"BAWATER OUTLET FITTING INSTALLATION
Squeeze out form-in-place gasket at a 3 mm width, and apply
at the position shown in the illustration.
Form-in-place gasket
Specified gasket:
Mitsubishi Genuine Part No. MD970389 or
equivalent
"CAENGINE COOLANT TEMPERATURE GAUGE UNIT
INSTALLATION
When reusing the bolts, apply the specified sealant on the
threads.
Sealant
Specified sealant:
3M
TMAAD Part No. 8672 or equivalent
"DAENGINE COOLANT TEMPERATURE SENSOR
INSTALLATION
Apply the specified sealant onto the threads.
Sealant
Specified sealant:
3M
TMAAD Part No. 8731 or equivalent
Caution
Make sure that the tool does not contact the connector
section (resin section).

ENGINE OVERHAUL -Rocker Arm and Camshaft11B-34
ROCKER ARM AND CAMSHAFT
REMOVAL AND INSTALLATION
1 2 3
4
5 6
78
910
111213
10±2N•m
14±1N•m
22±4N•m
11±1N•m
8.8±1.0 N•m
20±1N•m
14
15
16
Apply engine oil on
all sliding sections
before installing.
17
Removal steps
1. Cam position sensor
2. O-ring
3. Cover
4. Gasket
"FA5. Cam position sensing cylinder
"EA6. Cam position sensor support
"DA7. Camshaft oil seal
"CA8. Bearing cap, rear
"CA9. Bearing cap, front"CA10. Bearing cap No. 5
"CA11. Bearing cap No. 2
"CA12. Bearing cap No. 3
"CA13. Bearing cap No. 4
"BA14. Camshaft
15. Rocker arm
AA""AA16. Lash adjuster
17. Oil delivery body

ENGINE OVERHAUL -Rocker Arm and Camshaft11B-36
3. Apply sealant on the contact surfaces with the head shown
in the illustration.
Sealant
Specified sealant:
3M
TMAAD Part No. 8672 or equivalent
4. Install the bearing caps onto the cylinder head, and in
two to three steps tighten strongly.
5. Finally, tighten at the specified torque 20±1N•m.
6. Confirm that the rocker arm is correctly installed.
NOTE
Wipe off all excessive sealant.
"DACAMSHAFT OIL SEAL INSTALLATION
Install the oil seal using the special tool.
"EACAM POSITION SENSOR SUPPORT
INSTALLATION
Apply a 3 mm width of form-in-place gasket at the position
shown in the illustration.
Form-in-place gasket
Specified gasket:
Mitsubishi Genuine Part No. MD970389 or
equivalent
"FACAM POSITION SENSING CYLINDER
INSTALLATION
1. Set the exhaust camshaft at the No. 1 compression top
dead centre.
NOTE
The shaft will rotate slightly in the counterclockwise
direction by the force of the exhaust valve spring.
2. Install the cam position sensing cylinder’s vane (small)
and vane (large) at the positions shown in the illustration.
MD998713
Vane (small)
Cam position
sensorVane (large)