2007 MITSUBISHI LANCER EVOLUTION Engine oil pump

ENGINE OVERHAUL -Specifications11B-4
Unit: mm
Items
Standard valueLimited value
Oil pump, oil pan
Oil pump
Side clearance
Drive gear
Driven gear
0.08 - 0.14
0.06 - 0.12-
-
Piston, connecting rod
Piston
Press-in load N
Piston ring
Clearance between ring and ring groove
No. 1 ring
No. 2 ring
Closed gap
No. 1 ring
No. 2 ring
Oil
Connecting rod
Large end thrust clearance
Crankshaft
Pin section oil clearance
7,355 - 17,162
0.03 - 0.07
0.02 - 0.06
0.20 - 0.30
0.35 - 0.50
0.10 - 0.40
0.10 - 0.25
0.03 - 0.05-
0.1
0.1
0.8
0.8
1.0
0.4
0.1
Crankshaft, cylinder block
Crankshaft
End play
Journal section oil clearance
Cylinder block
Upper surface strain
Upper surface grinding limit (in combination with combined cylinder head)
Cylinder bore
Cylindricity
Clearance between piston and cylinder
0.05 - 0.25
0.03 - 0.04
0.05
-
85.0
0.01 or less
0.02 - 0.040.4
0.1
0.1
0.2
-
-
-
Turbocharger
Waste gate actuator operation pressure100 kPa-
Alternator
Alternator
Rotor coil resistanceΩ
Brush protrusion length
3-5
--
2
Starter motor
Starter motor
Deviation on commutator periphery
Commutator outer diameter
Undercut depth
0.05
29.4
0.50.1
28.8
0.2

ENGINE OVERHAUL -Specifications11B-5
MACHINING STANDARDS
Unit: mm
Items
Standard valueLimited value
Cylinder head, valve
Cylinder head
Oversize valve guide hole diameter
0.05 O.S.
0.25 O.S.
0.50 O.S.
Oversize valve seat hole diameter
Intake
0.3 O.S.
0.6 O.S.
Exhaust
0.3 O.S.
0.6 O.S.
12.05 - 12.07
12.25 - 12.27
12.50 - 12.52
35.30 - 35.33
35.60 - 35.63
33.30 - 33.33
33.60 - 33.63-
-
-
-
-
-
-
TIGHTENING TORQUE
ItemsTightening torque N·m
Alternator, ignition system
Oil level gauge guide bolt13±1
Water pump pulley bolt8.8±1.0
Alternator brace bolt (flange)23±3
Alternator brace bolt (washer)22±4
Alternator nut44±10
Crankshaft pulley bolt25±4
Center cover bolt3±0.5
Ignition coil bolt10±2
Spark plug25±5
Connector bracket bolt8.8±1.0
Timing belt
Timing belt cover bolt (flange)11±1
Timing belt cover bolt (washer)9±1
Power steering pump bracket bolt49±9
Tensioner pulley bolt49±6
Tensioner arm bolt21±4
Auto tensioner bolt23±3
Idler pulley bolt35±6
Crank angle sensor bolt8.8±1.0
Oil pump sprocket nut54±5
Crankshaft bolt162±5
Tensioner B bolt19±3
Counter balance shaft sprocket bolt46±3
Rocker cover bolt3.5±0.5
Engine support bracket bolt49±5

ENGINE OVERHAUL -Specifications11B-6
Items Tightening torque N·m
Camshaft sprocket bolt88±10
Fuel system
Throttle body bolt19±3
EGR valve bolt20±2
Fuel pressure regulator bolt8.8±2.0
Delivery pipe and injector bolt11±1
Vacuum hose and pipe bolt11±1
Solenoid assembly bolt9±1
Vacuum tank bracket bolt9±1
Secondary air system, intake manifold
Exhaust manifold heat protector bolt14±1
Vacuum hose and pipe bolt11±1
Air pipe assembly bolt (eye bolt)49±5
Air pipe assembly bolt (M6 flange)11±1
Air pipe assembly bolt (M8 flange)24±3
Air pipe assembly bolt (M8 washer)14±1
Air control valve assembly bolt22±4
Air control valve bracket bolt22±4
MDP sensor bolt5±1
Intake manifold stay bolt31±3
Intake manifold bolt (M8)20±2
Intake manifold bolt nut (M8)36±6
Exhaust manifold
Engine hanger bolt19±3
Turbocharger heat protector bolt14±1
O2sensor44±5
Exhaust fitting bracket bolt47±6
Exhaust fitting bolt nut59±5
Air outlet fitting bolt19±1
Oil return pipe bolt (flange)14±1
Oil return pipe bolt (washer)9±1
Turbocharger assembly and pipe bolt, nut59±5
Oil pipe bolt (M10 eye bolt)17±2
Oil pipe bolt (M12 eye bolt)31±2
Oil pipe bolt (M12 flange)11±1
Water pipe bolt (flange)10±1
Water pipe bolt (eye bolt)42±7
Exhaust manifold nut (M8)33±6
Exhaust manifold nut (M10)55±10
Water pump, water hose
Engine coolant temperature sensor29±10
Engine coolant temperature gauge unit10.8±1.0

ENGINE OVERHAUL -Specifications11B-7
Items Tightening torque N·m
Water outlet fitting bolt10±1
Thermostat housing bolt23±4
Water inlet pipe bolt (M6)10±1
Water inlet pipe bolt (M8)13±2
Water pump bolt14±1
Knock sensor23±2
Rocker arm, camshaft
Cam position sensor bolt8.8±1.0
Cover bolt10±2
Cam position sensing cylinder bolt22±4
Cam position sensor support bolt14±1
Bearing cap bolt20±1
Oil delivery body bolt11±1
Cylinder head, valve
Cylinder head bolt78±2→Completely loosen→20±2→90_+90_
Oil pump, oil pan
Drain plug39±5
Oil pan bolt9±3
Oil screen bolt19±3
Baffle plate bolt22±4
Oil pressure switch19±3
Oil cooler bypass valve54±5
Relief plug44±5
Oil filter bracket bolt19±3
Plug cap23±3
Flange bolt36±3
Oil pump case bolt23±3
Oil pump cover bolt17±1
Oil pump cover screw10±2
Piston, connecting rod
Connecting rod cap nut20±2+90_-94_
Crankshaft, cylinder block
Flywheel bolt132±5
Rear plate bolt11±1
Bell housing cover bolt9±1
Rear oil seal case bolt11±1
Beam bearing cap bolt25±2+90_- 100_
Check valve32±2
Throttle body
Throttle position sensor bolt2.0±0.5
Turbocharger
Waste gate actuator bolt11.3±1.5

ENGINE OVERHAUL -Alternator and Ignition System11B-12
ALTERNATOR AND IGNITION SYSTEM
REMOVAL AND INSTALLATION
1
13±1N•m
2
3
13
4
7
6
5
89
10
1211
22±4N•m8.8±1.0 N•m
25±5N•m 3±0.5 N•m
10±2N•m
8.8±1.0 N•m
23±3N•m
25±4N•m44±10 N•m
Removal steps
1. Oil level gauge
2. O-ring
3. Oil level gauge guide
4. O-ring
5. Water pump pulley
6. Alternator brace
7. Alternator8. Crankshaft pulley
9. Center cover
10. Spark plug cable
11. Ignition coil
12. Spark plug
13. Connector bracket

ENGINE OVERHAUL -Timing Belt11B-13
TIMING BELT
REMOVAL AND INSTALLATION
1
11±1N•m
2
3
4 56
7
8
910
11 1213
14 15
16 1718
192021 2223
2425
26
27
2829
30
313233
34
35
49±6N•m
21±4N•m
23±3N•m
11±1N•m11±1N•m
88±10 N•m
35±6N•m
54±5N•m 19±3N•m 46±3N•m 9±1N•m162±5N•m3.5±0.5 N•m
49±9N•m
8.8±1.0 N•m 49±5N•m
Removal steps
1. Timing belt front upper cover
2. Timing belt front center cover
3. Timing belt front lower cover
4. Power steering pump bracket
AA""MA5. Timing belt
"LA6. Tensioner pulley
7. Tensioner arm
"KA8. Auto tensioner
9. Idler pulley
10. Crank angle sensor
AB""JA11. Oil pump sprocket
AC""IA12. Crankshaft bolt
AD""IA13. Crankshaft sprocket
"IA14. Crankshaft sensing blade
15. Tensioner B
AE""HA16. Timing belt B
AF""GA17. Counter balance shaft sprocket
"FA18. SpacerAG""EA19. Crankshaft sprocket B
20. Crankshaft key
21. Breather hose
22. PCV hose
23. PCV valve
24. PCV valve gasket
25. Oil filler cap
"DA26. Rocker cover
"DA27. Rocker cover gasket A
28. Rocker cover gasket B
"CA29. Semi-circular packing
"BA30. Engine support bracket
AH""AA31. Camshaft sprocket bolt
32. Camshaft sprocket
33. Timing belt rear right cover
34. Timing belt rear left upper cover
35. Timing belt rear left lower cover

ENGINE OVERHAUL -Timing Belt11B-14
REMOVAL SERVICE POINTS
AA"TIMING BELT REMOVAL
1. To ensure that the timing belt is assembled in the same
direction when reused, using chalk, etc., make an arrow
showing the rotation direction on the back surface of
the timing belt.
2. Position the exhaust camshaft sprocket’s timing mark by
approx. one tooth before the No. 1 cylinder compression
top dead centre.
Caution
When removed at the compression top dead centre,
since the exhaust camshaft is at the position pressing
down on the valve, the sprocket could rotate in reverse
due to the force of the valve spring creating a
hazardous situation.
3. Loosen the lock nut for the tensioner pulley, and remove
the timing belt.
AB"OIL PUMP SPROCKET REMOVAL
1. Remove the plug on the left side of the cylinder block.
2. Insert a Phillips driver (shaft diameter 8 mm) to stop the
counter balance shaft left from rotating.
3. Loosen the flange bolt.
4. Remove the oil pump sprocket.
AC"CRANKSHAFT BOLT REMOVAL
1. Fix the flywheel with the special tool.
2. Remove the crankshaft bolt.
AD"CRANKSHAFT SPROCKET REMOVAL
Use the special tool to remove the sprocket if it is stuck
and hard to remove.
Timing marks
Phillips driver
MD998781
MD998778

ENGINE OVERHAUL -Timing Belt11B-17
3. Apply form-in-place gasket on the rocker cover at the
position shown in the illustration.
Sealant
Specified sealant:
3M
TMAAD Part No. 8672 or equivalent
4. Install the rocker cover onto the cylinder head before
the form-in-place gasket hardens.
"EACRANKSHAFT SPROCKET B INSTALLATION
Clean the crankshaft sprocket B installation surface before
degreasing the crankshaft sprocket B.
NOTE
Always degrease the surface to prevent a drop in the frictional
coefficient at the pressing section caused by the adherence
of oil.
"FASPACER INSTALLATION
1. Apply a slight amount of oil on the outer periphery of
the spacer (oil seal contact section).
2. Insert the spacer from the chamfered side as shown in
the illustration.
Caution
Reversed insertion of the spacer can cause damage
to the oil seal lip.
"GACOUNTER BALANCE SHAFT SPROCKET
INSTALLATION
1. Fix the counter balance shaft sprocket with the special
tool.
2. Tighten the counter balance shaft sprocket installation
bolt at the specified torque 46±3N•m.
"HATIMING BELT B INSTALLATION
1. Align the crankshaft sprocket B and counter balance shaft
sprocket timing marks with the timing mark on the oil
pump case.
2. Attach the timing belt B to the crankshaft sprocket B
and counter balance shaft sprocket.
Do not loosen the belt tension too much at this time.
Timing belt side
Crankshaft sprocket B
Crankshaft
Degrease
Spacer
Oil seal
Chamfer
MD998785
Timing
marks
Timing
marks