2007 MITSUBISHI LANCER EVOLUTION manual transmission

MANUAL TRANSMISSION OVERHAUL -Center Differential22B-50
(5) Install the front output shaft onto the side gear, and install
the snap ring.
(6) After assembling the side gear into the center differential
case, install the spacer onto the side gear.
(7) Match the alignment marks, install the center differential
flange, and temporarily fix the machine screw.
(8) Measure the backlash between the side gear and pinion.
Standard value: 0.025 - 0.150 mm
(9) If the backlash is not within the standard value, select
a spacer, and measure the backlash again.
NOTE
Adjust so that the backlash on both sides is even.
"DACENTER DIFFERENTIAL DRIVE GEAR
INSTALLATION
(1) Confirm that rust-proofing oil is applied, and then apply
sealant on all of the bolt threads.
Sealant
Specified sealant:
3M STUD Locking No.4170 or equivalent
(2) Tighten with the specified torque following the order shown
in the illustration.

MANUAL TRANSMISSION OVERHAUL -Transfer22B-51
TRANSFER
DISASSEMBLY AND REASSEMBLY
Apply gear oil on
all sliding sections
before installing.
10 7
86 5
3 4
1
2
9
23±3N•m
Disassembly steps
1. Dust seal guard
"EA2. Oil seal
"DA3. Oil seal
"AA4. O-ring
"AA5. O-ring"CA6. Oil seal
"BA7. Oil seal
"AA8. O-ring
9. Transfer cover
10. Transfer

MANUAL TRANSMISSION OVERHAUL -Transfer22B-52
REASSEMBLY SERVICE POINTS
"AAO-RING INSTALLATION
Apply hypoid gear oil on the O-ring.
Hypoid gear oil
Specified oil:
MITSUBISHI genuine “DIA-QUEEN SUPER” hypo-
id gear oil (GL-5) or equivalent
"BAOIL SEAL INSTALLATION
Apply hypoid gear oil on the lip section of the oil seal, and
install using the special tool.
Hypoid gear oil
Specified oil:
MITSUBISHI genuine “DIA-QUEEN SUPER” hypo-
id gear oil (GL-5) or equivalent
"CAOIL SEAL INSTALLATION
Apply hypoid gear oil on the lip section of the oil seal, and
install using the special tool.
Hypoid gear oil
Specified oil:
MITSUBISHI genuine “DIA-QUEEN SUPER” hypo-
id gear oil (GL-5) or equivalent
"DAOIL SEAL INSTALLATION
Apply hypoid gear oil on the lip section of the oil seal, and
install using the special tool.
Hypoid gear oil
Specified oil:
MITSUBISHI genuine “DIA-QUEEN SUPER” hypo-
id gear oil (GL-5) or equivalent
"EAOIL SEAL INSTALLATION
Apply hypoid gear oil on the lip section of the oil seal, and
install using the special tool.
Hypoid gear oil
Specified oil:
MITSUBISHI genuine “DIA-QUEEN SUPER” hypo-
id gear oil (GL-5) or equivalent
MD998800
MB990937MB990938
MB990887MB990891
MB990936

32-1
POWER PLANT
MOUNT
CONTENTS
GENERAL INFORMATION 2..................
SPECIAL TOOL 3............................
ENGINE MOUNTING 4........................TRANSMISSION MOUNTING 5................
ENGINE ROLL STOPPER, CENTERMEMBER
6 ............................................
CROSSMEMBER* 8..........................
WARNING REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES
WARNING!
(1) Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to personal
injury or death to service personnel (from inadvertent firing of the air bag) or to driver and passenger (from rendering
the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an authorized
MITSUBISHI dealer.
(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B - Supplemental
Restraint System (SRS) before beginning any service or maintenance of any component of the SRS or any SRS-related
component.
NOTE
The SRS includes the following components: SRS-ECU, SRS warning lamp, air bag module, clock spring, and interconnecting
wiring. Other SRS-related components (that may have to be removed/installed in connection with SRS service or maintenance) are
indicated in the table of contents by an asterisk (*).