2007 MERCEDES-BENZ ML320CDI seats

135 Controls in detail
Memory function*
The memory button and stored position
buttons are located on the entry side of
each front seat base.
MMemory button
1, 2, 3Stored position buttons
Switch on the ignition (
page 40).
or

Open the respective door.
Storing positions into memory
Adjust the seats (
page 43).

On the driver’s side, additionally adjust
the steering wheel (
page 48) and ex-
terior rear view mirrors (page 49) to
the desired positions.

Press memory buttonM.

Release memory buttonM and press
stored position1,2 or3 within
3 seconds.
All settings are stored to the selected
position.
Recalling positions from memory
Press and hold stored position
button1,2 or3 until the seat, steering
wheel and exterior rear view mirrors
have fully moved to the stored posi-
tions.
!
Do not operate the power seats using
memory buttonM if the seat backrest is in an
excessively reclined position. Doing so could
cause damage to front or rear seats.
Move seat backrest to an upright position first.
i
Releasing the stored position button stops
movement to the stored positions immediately.

217 Controls in detail
Climate control
Activating
Switch off the ignition (
page 40).

Press button9 (
page 208).
The indicator lamp on the button
comes on.
Deactivating

Press button9 (
page 208).
The indicator lamp on the button goes
out.
Rear climate control*
The control panel for the rear climate
control is only available if your vehicle is
equipped with seat heating* for the rear
seats.
The control panel is located on the rear of
the front center console.Rear climate control panel
i
The residual heat is automatically turned off:


when the ignition is switched on


after about 30 minutes


if the coolant temperature is too low


if the battery voltage drops
1
Left rear center air vent, adjustable
2
Right rear center air vent, adjustable
3
Rear climate control on
(automatic mode)
4
Air distribution (directs air through
the center air vents)
5
Air distribution (directs air through
the footwells and side air vents)
6
Rear air conditioning off

236 Controls in detailPower windowsOpening and closing
The door windows are opened and closed
electrically. The switches for all door win-
dows are located on the driver’s door con-
trol panel (
page 36). The switches for
the respective door windows are located
on the control panels of the front passen-
ger door and the rear doors.
1Left rear door window
2Left front door window
3Right front door window
4Right rear door window
5Override switch (
page 93)

Switch on the ignition (
page 40).
Warning!
G
When closing the windows, make sure that
there is no danger of anyone being harmed
by the closing procedure.
Activate the override switch (
page 94)
when children are riding in the back seats of
the vehicle. The children could otherwise in-
jure themselves, e.g. by becoming trapped
in the window opening.
The closing of a door window can be imme-
diately halted by releasing the switch or, if
switch was pulled past the resistance point
and released, by either pressing or pulling
the respective switch.
If a door window encounters an obstruction
that blocks its path in a circumstance where
you pulled the switch past the resistance
point and released it to close the door win-
dow, the automatic reversal function will
stop the window and open it slightly.

282 Controls in detailLoadingLoad distributionThe gross vehicle weight which is the
weight of the vehicle including fuel, tools,
spare wheel, installed accessories, pas-
sengers and luggage/cargo must never
exceed the load limit and Gross Vehicle
Weight Rating (GVWR) for your vehicle as
specified on the placard located on the
driver’s door B-pillar (
page 530). In addi-
tion, the load must be distributed in such a
way so that the weight on each axle never
exceeds the Gross Axle Weight Rating
(GAWR) for the front and rear axle. The
GVWR and GAWR for your vehicle are indi-cated on the certification label which can
be found on the driver’s door B-pillar
(
page 530).
For more information, see “Tire and Load-
ing Information” (
page 369).
The handling characteristics of a fully load-
ed vehicle depend greatly on the load dis-
tribution. It is therefore recommended to
load the vehicle according to the illustra-
tions shown, with the heaviest items being
placed towards the front of the vehicle.
Please pay attention to and comply with
the following instructions when loading the
vehicle and transporting cargo:


Always place items being carried
against front or rear seat backrests,
and fasten them as securely as possi-
ble.


The heaviest portion of the cargo
should always be kept as low as possi-
ble against front or rear seat backrests.For additional safety when transporting
cargo while the rear seats are unoccupied,
fasten the outer seat belts crosswise into
the opposite side buckles.
i
The cargo compartment is the preferred
place to carry objects. The expanded cargo com-
partment (
page 284) should only be used for
items which do not fit in the cargo compartment
alone.

283 Controls in detail
Loading
Cargo tie-down rings
Your vehicle is equipped with six cargo
tie-down rings.
Carefully secure cargo by applying even
load on all rings with rope of sufficient
strength to hold down the cargo.Cargo compartment
Four cargo tie-down rings are located in
the cargo compartment.
1Cargo tie-down ringBehind front seats
Two cargo tie-down rings are located in the
footwell behind the driver’s and passenger
seat.
1Cargo tie-down ringi
While the partition net* (
page 287) will
help protect you from smaller objects, it cannot
prevent the movement of large, heavier objects
into the passenger compartment in an accident,
during hard braking or sudden maneuvers. Such
items must be properly secured using the cargo
tie-down rings in the cargo compartment floor.

284 Controls in detailLoadingHooks
Four hooks are located on the rear com-
partment trim panels, two on each side.
1Hook
Use the hooks to secure light weight items
only. The maximum permissible weight per
hook is 9 lbs (4 kg).
Expanding cargo compartment
You can separately fold the left and right
rear seat backrests to expand the cargo
compartment.
Folding the rear seat backrest forwardWarning!
G
When expanding the cargo compartment,
always fully fold the corresponding seats
and, if so equipped, always use the partition
net* (
page 287) when transporting cargo.
Unless you are transporting cargo, the back-
rests must remain properly locked in the up-
right position.
In an accident, during hard braking or sud-
den maneuvers, loose items will be thrown
around inside the vehicle, and can cause
injury to vehicle occupants unless the items
are securely fastened in the vehicle.
Always use the cargo tie down rings
(
page 283).
Warning!
G
Never drive the vehicle with the tailgate
open. Deadly carbon monoxide (CO) gases
may enter vehicle interior resulting in un-
consciousness and death.!
Always release the seat cushion and fold it
up before folding the seat backrest forward. The
covering on the seat backrest may otherwise be
damaged.
When the seat backrest are folded forward, the
front seats may not be moved to the rearmost
position. Otherwise you could damage the front
and second-row seats.

286 Controls in detailLoadingReturning the rear seat backrest to
original position
1Seat backrest
2Seat cushion
Fold seat backrest1 rearward until it
engages.
The red indicator5 (
page 285)
should no longer be visible.

Fold seat cushion2 rearward until it
locks into position.

Check for secure locking by pushing
and pulling on the seat backrest.
Cargo compartment cover blind
The cargo compartment cover blind can be
installed behind the rear seats.1Handle
2Mount
Rolling out blind

Pull blind on handle1 across the car-
go compartment.

Guide blind into mounts2 and re-
lease.
Rolling up blind

Disengage blind and guide retraction
by its handle1.
Warning!
G
If a red indicator is visible with the backrest
up, then the backrest is not properly locked
into position.
Always lock backrest in its upright position
when the rear seats are occupied, or the ex-
tended cargo compartment is not in use.
Check for secure locking by pushing and
pulling on the backrest.!
With the cargo compartment cover blind in-
stalled, do not pile luggage higher than the lower
edges of the rear side windows.

287 Controls in detail
Loading
Removing blind
1Release button
2Blind
Roll the blind up (
page 286).

Push release button1.

Pull blind2 to the left against the
spring pressure until the spring in the
cover audibly engages.

Remove the blind.
Installing blind

Place left side of blind2 in left mount.

Position right side of blind2 over right
mount.

Press release button1 and guide
cover2 into mount.

Make sure the cargo compartment
cover blind is securely fastened.
Partition net*
i
Before removing cargo compartment cover
blind behind the rear seats, fold the left or right
rear seat forward. Afterwards, return the left or
right rear seat into its original position.
i
Before installing cargo compartment cover
blind behind the front seats, fold the rear seats
forward.
Warning!
G
Make sure the partition net is properly en-
gaged at top and bottom position and the
tightening belts are securely fastened.
Never use a damaged partition net.
To help avoid personal injury from smaller
objects being thrown around in the occu-
pant compartment during a collision or sud-
den maneuver, always use partition net
when transporting cargo.
The partition net cannot prevent the move-
ment of large, heavier objects into the pas-
senger compartment in an accident. Such
items must be properly secured using the
cargo tie-down rings (
page 283) in the
cargo compartment floor.
Passenger use of seats behind installed par-
tition net is restricted because of the foot-
well being taken up by the net.