Page 245 of 723
244 Control systems
COMAND automatic climate control
You can operate the automatic climate
control via COMAND or via the buttons on
the automatic climate control panel
(
page 453).
Some of the special climate control func-
tions can only be set via COMAND.The following automatic climate control
functions can be operated via COMAND:
iThe components and operating principles of
COMAND can be found on (
page 81).
Warning!G
When operating the automatic climate con-
trol, the air that enters the passenger com-
partment through the air vents can be very
hot or very cold (depending on the set tem-
perature). This may cause burns or frostbite
to unprotected skin in the immediate area of
the air vents.
Always keep sufficient distance between un-
protected parts of the body and the air
vents. If necessary, use the air distribution
adjustment (
page 246) to direct the air to
air vents in the vehicle interior that are not
in the immediate area of unprotected skin.
Warning!G
Follow the recommended settings for heat-
ing and cooling given on the following pages
and pages in the “Controls in detail” part
(
page 453) Otherwise the windows could
fog up, impairing visibility and endangering
you and others.
FunctionPage
Temperature245
Air distribution246
Air volume246
Switching off cooling (“ACOFF”)247
Central climate control (“Mono”)248
Footwell temperature249
Air flow from air vents249
Page 246 of 723
245 Control systems
COMAND automatic climate control
The automatic climate control menu is
called up via the climate control settings.
Climate control settings with functions
(submenus)
1Temperature, left
2Air distribution, left
3Air volume, left
4Central menu, climate control
5Air volume, right
6Air distribution, right
7Temperature, right
Setting temperature
Use the temperature controls %$
(
page 453) in the center console or
COMAND climate control settings to sepa-
rately adjust the air temperature on each
side of the passenger compartment.
Select climate control settings Tem-
perature, left or right and then
pressn.
Changing temperature: Slide qmr or
rotate ymz.
Exiting menu: Press n, back
buttonL in the center console
(
page 82) or slideomp.
The setting is saved.
Page 247 of 723
246 Control systems
COMAND automatic climate control
Adjusting air distribution
You can adjust the air distribution sepa-
rately for the driver’s and front passenger’s
side.
Select climate control settings Air
distribution, left or right.
Changing air distribution:
Rotateymz.
The symbol for air distribution changes.
The direction and size of the arrows
represent the air distribution.
Exiting menu: Press n, back
buttonL in the center console
(
page 82) or slideomp.
The setting is saved.
Adjusting air volume
Use buttonsQ (
page 453) in the cen-
ter console or COMAND climate control
settings to separately adjust the air vol-
ume on each side of the passenger com-
partment.
Select climate control settings Air
volume, left or right.
iWhen you change the air distribution, the au-
tomatic function of the climate control system is
switched off.
iWhen you change the air volume, the auto-
matic function of the climate control system is
switched off.
Page 248 of 723
247 Control systems
COMAND automatic climate control
Changing air volume: Slide qmr or
rotate ymz.
Exiting menu: Press n, back
buttonL in the center console
(
page 82) or slideomp.
The setting is saved.Central climate control menu via
COMAND
The central climate control menu is in the
center of the climate control settings.
When the automatic climate control is
switched on, you will see “on” in the cen-
tral menu. The following functions can only
be operated in the central climate control
menu via COMAND:
Select climate control settings Cen-
tral menu.Switching cooling on or off
The cooling function, only operational
when the engine is running, cools the vehi-
cle interior down to the selected tempera-
ture. The cooling function also
dehumidifies the air in the vehicle interior,
thus preventing the windows from fogging
up.
The “AC
OFF” function is used to permanent-
ly switch off the cooling function of the au-
tomatic climate control system.
FunctionPage
Switching off cooling (“ACOFF”)247
Central climate control (“Mono”)248
Footwell temperature249
Air flow from air vents249
iCondensation may drip out from underneath
the vehicle. This is normal and not an indication
of a malfunction.
Page 249 of 723
248 Control systems
COMAND automatic climate control
Select climate control settings Cen-
tral climate control menu.
Selecting “ACOFF”: Slide qmr or
rotateymz.
Confirming selection: Press n.
A checkmark appears when the cooling
is switched off.“AC
OFF” appears in the central menu of
the climate control settings.
Selecting “Mono” mode
“Mono” is used to adjust the climate zones
for the entire vehicle at the same time.
When the “Mono” function is switched on
and you change the climate on the driver’s
side, these changes will be carried out in
the same manner for all climate zones.
Select climate control settings Cen-
tral climate control menu.
Selecting “Mono”: Slide qmr or
rotateymz.
Confirming selection: Press n.
A checkmark appears when the func-
tion has been selected.
Exiting menu: Press back button L
in the center console (
page 82) or
slideomp.
The “Mono” function is automatically
switched off when you:
change an automatic climate control
setting for the front passenger’s side
using COMAND
operate a button from the automatic
climate control for the front passen-
ger’s side
operate one of the buttons for the rear
climate control system
Warning!G
If you turn off the cooling function, the
vehicle will not be cooled when weather
conditions are warm. The windows can fog
up more quickly. Window fogging may
impair visibility and endanger you and
others.!If the air conditioning cannot be turned on
again, this indicates that the air conditioning is
losing refrigerant. The compressor has turned it-
self off.
Have the air conditioning checked at the nearest
authorized Mercedes-Benz Center.
Page 250 of 723
249 Control systems
COMAND automatic climate control
Adjusting footwell temperature
The “Footwell Temperature” function is
used to adjust the temperature difference
between the footwell and the rest of the
passenger compartment.
The higher the selected value, the higher
the temperature in the footwell will be.
Select climate control settings Cen-
tral climate control menu.
Selecting “Footwell Temperature”:
Slide qmr or rotate ymz and then
pressn.
Changing temperature difference:
Slide qmr or rotate ymz.
Exiting menu: Press n, back
buttonL in the center console
(
page 82) or slideomp.
The setting is saved.
Adjusting air flow from air vents
The “Airflow” setting defines air distribu-
tion and air volume in automatic mode:
“Focused” (default setting, increased
air flow)
“Medium” (reduced air flow)
“Diffuse” (minimal air flow)
Select climate control settings Cen-
tral climate control menu “Airflow”.A selection list appears.
The current setting is indicated by a
dotR.
Changing air flow: Slide qmr or
rotateymz.
Confirming selection: Press n.
iIn automatic mode, this setting optimizes
the footwell temperature when outside tempera-
tures are low.
iIn automatic mode, this setting optimizes
the air flow when outside temperatures are high.
iWhen the interior ambient temperature of
the vehicle is very hot and the automatic climate
control is cooling the interior, the setting for air
flow is temporarily overridden.
Page 251 of 723
250 Control systems
COMAND seats
When adjusting the seats, observe the
safety notes in the section “Seats”
(
page 339).
Operating seats via COMAND
The following seat adjustments can be
made via COMAND:Selecting a seat
You must first select the seat for which you
would like to make adjustments.
1Seat menu button
Press O.
The main area is active.
Switching to the bottom menu line:
Slide qmr.
Example illustration (vehicles with Drive-dy-
namic multicontour seat*)
Selecting seat: Slide omp or
rotateymz.
Confirming selection: Press n.
iThe components and operating principles of
COMAND can be found on (
page 81).
SettingsPage
Lumbar support (CL 550)251
Drive-dynamic multicontour
seats*252
Page 252 of 723
251 Control systems
COMAND seats
Exiting menu
There are several ways to exit the seat
menu.
Press O again.
or
Press any shortcut button.
or
Select another main function from the
main menu line.
Lumbar support (CL 550)
To support the spine, you can adjust the
curvature of the front seat backrests.
Press O.
The main area of the COMAND display
is active. A scale appears.
1Scale
2Cursor
3Current seat
4Current setting
Select seat (page 250).
Adjusting lumbar support:
Slideomp or rotate ymz until desired
setting is reached.
Confirming selection: Press n.
Switching to the bottom menu line:
Slide omp.
Confirming selection: Press n.
iAfter you have pressedO, the seat last
adjusted is active.
