2007 Lancia Musa warning light

253
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
ENGINE STARTING
EMERGENCY START-UP
If the Lancia CODE cannot deactivate the engine
immobilising system, the
YandUwarning lights
stay on and the engine will not start.
To start the engine the emergency start-up can be
performed.
Read the whole procedure carefully before trying to
carry it out. If you make a mistake, you must turn
the ignition key back to STOP and repeat the whole
operation from beginning.
Proceed as follows:
❒Read the 5-figure electronic code given on the
CODE card;
❒Turn the ignition key to MAR;
❒Press and hold down the accelerator pedal. The
instrument panel warning light
Uwill come on
for about 8 seconds and then go out;
❒Release the accelerator pedal and get ready to
count the flashes of the
Uwarning light;
❒Count the number of flashes that corresponds to
the first figure of the code on the CODE card,
then press the accelerator pedal and keep it there
until the
Uwarning light comes on for four
seconds and then goes out; release the
accelerator pedal;
❒TheUwarning light will start flashing again:
after it has flashed the number of times that
corresponds to the second figure on the CODE
card, press the accelerator pedal to the floor and
keep it there;
❒Do the same for the remaining figures on the
CODE card;
❒Once the final figure has been entered, keep the
accelerator pedal pressed. The
Uwarning light
will light up for four seconds and then go out;
release the accelerator pedal;
❒Rapid flashing of the warning light U(for
about 4 seconds) confirms the operation has
been carried out successfully;
❒Start the engine by turning the ignition key from
MAR to AVV.
If however the warning light
Ustays on, turn the
ignition key to STOP and repeat the procedure from
step one
IMPORTANT After an emergency start-up, you
should contact a Lancia Dealership otherwise you
will have to repeat the procedure described each
time you want to start the engine.

254
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
JUMP STARTING
If the battery is flat, it is possible to start the engine using an
auxiliary battery with the same capacity or a little higher than the flat
one.
Proceed as follows:
❒Connect positive terminals (+) of the two batteries with a jump
lead;
❒With a second lead, connect the negative terminal (–) of the
auxiliary battery and to an earthing point Eon the engine or the
gearbox of the car to be started;
❒Start the engine;
❒When the engine has been started, remove the leads reversing the
order above.
If after a few attempts the engine does not start, do not insist but
contact the nearest Lancia Dealership.
IMPORTANT Do not directly connect the two negative terminals:
sparks could ignite the flammable gas from the battery. If the other
battery is fitted in a vehicle, prevent accidental contacts between the
metal parts of the two vehicles.
Under no circumstances should a battery charger be used to start the engine: it could damage the
electronic systems and in particular the ignition and injection control units.
WARNING
Do not carry out this procedure if you lack experience; if it is not done correctly it
can cause very intense electrical discharges. In addition, the fluid contained in the
battery is poisonous and corrosive. Avoid contact with skin and eyes. You are also
advised not to put naked flames or lighted cigarettes near the battery and not to
cause sparks.
L0D0160m

255
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
BUMP STARTING
Never bump start the engine (by pushing, towing,
or coasting downhill) as this could cause fuel to
flow into the catalytic exhaust system and damage
it beyond repair.IMPORTANT Remember that until the engine has
started the brake booster and electrical power
steering systems will not work and a greater effort
will therefore be required to press the brake pedal
or turn the steering wheel.
WARNING
Alert other drivers that the car is stationary in compliance with local regulations:
hazard warning lights, warning triangle etc. Any passengers on board should
leave the car, especially if it is heavily laden. Passengers should stay away from
oncoming traffic while the wheel is being changed on. If the wheel is being
changed on a steep or badly surfaced road, place the wedges or other suitable
material under the wheel to stop the car.

256
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
QUICK TYRE REPAIR KIT - FIX & GO
automatic (where provided)
The quick tyre repair kit Fix & Go automatic is placed in the boot.
The kit includes:
❒bottle A containing sealer and fitted with:
– filling pipe B;
– sticker C bearing the notice “max. 80 km/h”, to be placed in a po-
sition visible to the driver (on the instrument panel) after fixing
the tyre;
❒instruction brochure, to be used for prompt and proper use of the quick
repair kit and to be then handed to the personnel charged with han-
dling the treated tyre;
❒compressor D including gauge and connections;
❒a pair of protection gloves located in the side space of the compres-
sor;
❒adapters for inflating different elements.
In the kit container (placed in the boot under the carpet) are also
housed the screwdriver and the tow hitch.
L0D0361m
L0D0362m
Hand the instruction brochure to the personnel charged with treating the tyre
repaired with the kit.WARNING

257
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
IMPORTANT Do not use the quick repairing kit if
the tyre is damaged due to driving with the wheel
flattened.IT SHOULD BE NOTICED THAT:
The sealing fluid of the quick tyre repair kit is
effective with external temperatures between –20 °C
and +50 °C.
The sealing fluid has limited life.
In the event of a puncture caused by foreign bodies, it is possible to repair tyres showing damages
on the track or shoulder up to max 4 mm diameter.
The compressor shall not be operated for more than 20 minutes. Risk of
overheating!. Tyres repaired with the quick tyre repair kit shall be used
temporarily only.WARNING
Repairs are not possible in case of damages on the wheel rim (bad groove
distortion causing air loss). Do not remove foreign bodies (screws or nails) from
the tyre.WARNING
Holes and damages on the tyre side walls cannot be repaired. Do not use the
quick tyre repair kit if damaging is due to running with flat tyre.WARNING

258
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
INFLATING PROCEDURE
❒Pull up the handbrake. Loosen tyre inflation valve cap, take out the
filler hose A and screw the ring nut B on the tyre valve;
L0D0363m
Put on the protection gloves provided together with quick tyre repair kit.WARNING
Replace the cylinder if sealer has run out. Do not throw away the cylinder and the sealing fluid.
Have the sealing fluid and the cylinder disposed of in compliance with national and local
regulations.
WARNINGThe cylinder contains ethylene glycol. The cylinder contains latex: it can cause
allergic reactions. It is harmful if ingested or inhaled and irritant for the eyes and
in case of contact. In case of contact rinse immediately with water and take off
contaminated clothes. If swallowed, do not induce vomit, rinse out the mouth,
drink a lot of water and call the doctor immediately. Keep away from children.
This product must not be used by asthmatics. Do not inhale vapours. Call the
doctor immediately in case of allergic reactions. Keep the cylinder in the space
provided for the purpose and far from heat. The sealing fluid has limited life.

259
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
❒make sure the compressor switch D is set to 0 (off), start the engine
and fit plug A into the nearest current outlet and then turn on the com-
pressor by setting switch D to I (on). Inflate the tyre to the pressure
specified in paragraph “Inflation pressure” in section “Technical Spec-
ifications”.
Check tyre pressure on gauge F with compressor off to obtain pre-
cise reading;
❒if after 5 minutes it is still impossible to reach at least 1.5 bar, disen-
gage compressor from valve and current outlet, then move the car forth
for approx. ten metres in order to distribute the sealing fluid inside the
tyre evenly, then repeat the inflation operation;
❒if after this operation it is still impossible after 5 minutes to reach at
least 1.8 bar, do not start driving since the tyre is excessively damaged
and the quick tyre repair kit cannot guarantee suitable sealing, con-
tact Lancia Dealership;
L0D0364m
L0D0177m
L0D0366m
WARNINGApply the sticker in a visible position for
the driver to indicate that the tyre has
been treated with the quick tyre repair
kit. Drive carefully especially when
cornering. Do not exceed 80 km/h. Avoid
heavy braking and accelerating.
WARNINGIf the pressure falls below 1.8 bars, do not
drive any further: the quick tyre repair
kit Fix & Go automatic cannot guarantee
proper hold because the tyre is too much
damaged. Contact Lancia Dealership.

260
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
It is of vital importance to communicate that the tyre has been repaired using the
quick tyre repair kit. Hand the instruction brochure to the personnel charged with
treating the tyre repaired with the kit.WARNING
❒if reaching the tyre pressure specified in paragraph “Inflation pressure”
in section “Technical Specifications”, start driving immediately;
❒after driving for about 10 minutes stop and check again the tyre pres-
sure; pull up the handbrake;
❒if at least 1.8 bar pressure is read, restore proper pressure (with engine
running and handbrake on) and restart;
❒drive with the utmost care to the nearest Lancia Dealership.
FOR CHECKING AND RESTORING PRESSURE ONLY
The compressor can be also used just for restoring pressure.
Disconnect the quick connection and connect it directly to the tyre
valve; in this way the cylinder is not connected to compressor and the
sealing fluid will not flow into the tyre.
CYLINDER REPLACEMENT PROCEDURE
To replace the cylinder proceed as follows:
❒disconnect connection A;
❒turn counter-clockwise the cylinder to replace and raise it;
❒fit the new cylinder and turn it clockwise;
❒connect connection A to the cylinder and fit the transparent tube B in-
to the proper space.
L0D0367m
L0D0368m