2007 KIA CARNIVAL reset

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
1.Disconnect the negative ( - ) battery terminal.
2. Remove the overhead console and loosen sunroof motor bracket (A) mounting bolts (4EA).
3.Remove sunroof motor mounting screw (3EA) and disconnect connector (10pin). And then remove the sun roof
motor.
RESETTING THE SUNROOF
Whenever the vehicle battery is disconnected or discharged, or you use the emergency handle to operate the sunroof,
you have to reset your sunroof system as follows :
1. Turn the ignition key to the ON position. Press and hold the TILT UP button more than 15s until the sunroof has
tilted upward/downward slightly.
2. When this is complete, Press and hold the TILT UP button once again until the sunroof has raised above and
returned to the maximum TILT UP position.
When this is complete, the sunroof system is reset.

2007 > 2.7L V6 GASOLINE >
DESCRIPTION
The trip computer displays information related to driving, including compass, distance to empty, elapsed time, average
fuel consumption and outside temperature on the display. To change the function as described below, push the MODE
button lesser than 2 sec. Distance to empty → elapsed time → average fuel consumption → outside temperature →
OFF.
Compass is always displayed except for OFF mode.
OPERATION
1. COMPASS
The vehicle compass displays the direction (8 directions) where the vehicle is heading. Compass is displayed when
driving.
2.DISTANCE TO EMPTY
This mode indicates the estimated distance to empty based on the current fuel in the fuel tank and the amount of
fuel delivered to the engine. The meter’s working range is from 30 to 1500 miles (50 to 1500 km) by the 1km or
1mile.
When the remaining distance is below 30 miles (50km), a blinking “ - - - - ” symbol will be displayed.
The unit can be changed by press the reset button for more than 4 sec. If the unit of distance to empty is changed,
the unit of average fuel consumption is changed together.
3.ELAPSED TIME
This mode indicate the total time traveled since the last driving time reset while the engine is running.
Press the reset button for less than 4sec, clears the driving time to zero.

4.AVERAGE FUEL CONSUMPTION
This mode calculates the average fuel consumption from the total used fuel and the distance. The meter's working
range is from 0.0 to 99.9 L/100km or MPG(mile per gallon).
Press the reset button for less than 4 sec, when the average fuel consumption is being displayed, clears the
average fuel consumption to “ - - “ until the vehicle is moved to 0.3 miles(500m).
The unit can be changed by press the reset button for more than 4 sec. If the unit of average fuel consumption is
changed, the unit of distance to empty is changed together.
5.OUTSIDE AMBIENT TEMPERATURE
This mode indicates the outside temperature around the vehicle form - 40°C to 60°C (from - 40°F to 140°F).
The unit can be changed by press the reset button for more than 4 sec.

2007 > 2.7L V6 GASOLINE >
ADUSTMENT
CORRECTION MODE
1. The correction process is necessary for displaying correct direction of by removing the effect of magnetized car
body components.
2. Push Mode button for 2 sec - 4.5 sec. And then "turn" is displayed and "DIR" is blinking with 0.5 sec intervals.
3.Automatic correction is done when the vehicle turns 720° in normal driving condition (the correction is invisible to
the driver).
a.The correction data is updated if the automatic correction data is better than the present correction data.
b. Turning direction is not important.
c. If the correction process is not finished after the vehicle turns 720°, turn the vehicle some more degree.
4. After finishing the correction process, the compass displays the present direction.
5. If the correction process is not finished until 5 minutes this mode is cancelled and the compass returns to normal
mode with restoring the previous correction data.
DECLINATION CORRECTION (VARIANT REGION CHANGE MODE)
1.Change the "Declination Setting Value" according to the regional declination to synchronize the true north and
vehicle's north.
2. Push the mode button longer than 4.5 Sec to enter the declination correction mode. ('DIR' is on)
3.Screen after 4.5 sec.
4.Push the reset button longer than 0.1 Sec to change the declination setting Value (Steps by 5° to East. After East
30, wraps to West 30)
5. Push the mode button more than 1sec, new data is stored on EEPROM and VFD displays normal direction.
6. Without any effective input for 30 seconds, the trip computer displays the previous declination angle with blinking
for 2 sec and displays normal direction.