2007 KIA CARNIVAL alternator

Alternator

2007 > 2.7L V6 GASOLINE >
REMOVAL
1.Disconnect the battery negative terminal first, then the positive terminal.
2. Disconnect the alternator connector, and remove the cable from alternator "B" terminal.
3. Remove the drive belt.
4. Pull out the through bolt and then remove the alternator(A).
5.Installation is the reverse of removal.
DISASSEMBLY
1.Remove the alternator cover(A) using a screw driver(B).
2.Remove the slip ring guide(A).
3. Loosen the mounting bolts(B) and disconnect the brush holder assembly(C).
4.Remove the rectifler(A) with 4 screws.

2.Check that there is no continuity between the slip rings and the rotor (B) or rotor shaft (C).
3. If the rotor fails either continuity check, replace the alternator.
INSPECT STATOR
1.Check that there is continuity between each pair of leads (A).
2.Check that there is no continuity between each lead and the coil core.
3. If the coil fails either continuity check, replace the alternator.

2007 > 2.7L V6 GASOLINE >
POWERTRAIN CONTROL MODULE (PCM)
1.HARNESS CONNECTOR
2. TERMINAL FUNCTION
CONNECTOR [C151- 1]
Pin
No. Description
Connected to
1 2nd CAN [High] Multi- Purpose Check Connector
2 2nd CAN [Low] Multi- Purpose Check Connector
3 -y
4 -y
5 -y
6 -y
7 -y
8 -y
9 -
10 Power Steering Switch signal input Power Steering Switch
11 -y
12 -y
13 Clutch Switch signal input Clutch Switch
14 -y
15 Alternator load signal input Alternator
16 Cruise Switch ground Cruise Switch
17 -y
18 A/C switch "ON" signal input A/C Switch
19 -y
20 -y
21 Brake switch signal input Brake Switch
22 -y
23 Brake lamp signal input Brake Switch
24 -y
25 Cruise Switch signal input Cruise Switch
26 A/C thermal switch signal input A/C Thermal Switch
27 Diagnostic Data Line (K- Line) Data Link Connector (DLC)

15Alternator load signal input IdlePulseHi: Battery Voltage
13.67V
Lo: Max 1.5 V - 0.125mV
16 Cruise Switch ground IdleDCMax. 50 mV 22.44mV
17 - yy y y
18 A/C switch "ON" signal input A/C Relay OFF
DCBattery Voltage
12.37V
A/C Relay ON Max. 1.0V- 25mV
19 - yy y y
20 - yy y y
21 Brake switch signal input Pedal Release
DCBattery Voltage
13.97V
Pedal Push Max. 0.5V- 25mV
22 - yy y y
23 Brake lamp signal input Pedal Release
DCMax. 0.5V
- 225mV
Pedal Push Battery Voltage12.97V
24 - yy y
25 Cruise Switch signal input All Release
DC4.3 ~ 4.7V
4.39V
Main SW Battery Voltage13.37V
Set SW 1.3 ~ 1.7V1.38V
Resume SW 2.8 ~ 3.2V2.82V
Cancel SW - 0.2 ~ 0.2V- 37.54mV
26 A/C thermal switch signal input A/C OFF
DCMax. 1.0V
- 25mV
A/C ON Battery Voltage12.57V
27 Diagnostic Data Line (K- Line) When
transmitting
PulseHi: Min. Vbatt
× 80% 11.57V
Lo: Max. Vbatt ×
20% 175mV
When receiving Hi: Min. Vbatt
× 70% y
Lo: Max. Vbatt ×
30% y
28 - yy y y
29 - yy y y
30 - yy y y
31 - yy y y
32 A/C Pressure Transducer signal
input A/C OFF
DC0 ~ 5V 1.36V
A/C ON 1.83V
33 Sensor ground IdleDCMax. 50 mV 22.66mV
34 - yy y y
35 - yy y y
36 - yy y y
37 - yy y y
38 Battery voltage supply after main
relay IG OFF
DCMax. 1.0 V
- 25mV
IG ON Battery Voltage12.77V
39 Battery voltage supply after main
relay IG OFF
DCMax. 1.0 V
- 25mV
IG ON Battery Voltage12.77V
IG OFF Max. 1.0 V- 25mV