2007 ISUZU KB P190 brake

5C-60 BRAKES
VACUUM BOOSTER
REMOVAL AND INSTALLATION




This illustration is based on the RHD model
RTW 75CMF000501


Removal Steps
▲ 1. Brake pipe
▲ 2. Master cylinder fixing nut
▲ 3. Bracket
▲ 4. Master cylinder assembly
5. Vacuum hose
6. Snap pin
7. Vacuum booster fixing nut
8. Gasket
9. Spacer
10. Vacuum booster assembly

Installation Steps
▲
10. Vacuum booster assembly
▲ 9. Spacer
▲ 8. Gasket
▲ 7. Vacuum booster fixing nut
▲ 6. Snap pin
▲ 5. Vacuum hose
4. Master cylinder assembly
3. Bracket
2. Master cylinder fixing nut
1. Brake pipe



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

BRAKES 5C-61




RTW 75CSH002701

Important Operation-Removal
1. Brake pipe
W hen hurdling, be careful not to spill brake fluid over the
painted surfaces, as damage to the paint finish will result.
2. Master Cylinder Fixing Nut
3. Bracket
4. Master Cylinder Assembly
NOTE:
W hen removing the master cylinder from the vacuum booster,
be sure to get rid of the internal negative pressure of the
vacuum booster (by, for instance, disconnecting the vacuum
hose) in advance.
If any negative pressure remains in the vacuum booster, the
piston may possibly come out when the master cylinder is
being removed, letting the brake fluid run out.
W hile removing the master cylinder, do not hold the piston as it
can be easily pulled out.



Inspection and Repair
Vacuum Hose (The built in check valve)
360R300002

1) Inspect the check valve, which is installed inside the
vacuum hose.
2) Blow air into the hose from the booster side as shown in the illustration. The air should pass freely through the
hose.
3) Blow air into the hose from the engine side. The check valve should close to block the passage of air.
The vacuum hose and built-in check valve must be
replaced as a set if either is found to be defective.

Important Operation-Installation
10. Vacuum Booster Assembly
Note:
•
Adjustment of push rod of vacuum booster is not carried
out. W hen vacuum booster is damaged it exchanges for a
new article. (Push rod is adjusted)
• Measurement of primary piston position by the side o
f
master cylinder is unnecessary.
9. Spacer
8. Gasket
7. Vacuum Booster Fixing Nut
6. Snap Pin
Install the vacuum booster assembly to the dash panel and
pedal mounting bracket.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

5C-62 BRAKES

360r300003
5. Vacuum Hose
The check valve (2) is built-in to the vacuum hose.
W hen installing the vacuum hose make sure that the arrow on
the hose is facing the engine (1).
Note:
• Do not apply oil to the vacuum hose.
• Installation direction is very important. The booster will not
operate if the vacuum hose is installed in the wrong
direction.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

BRAKES 5C-63
DISASSEMBLY

VACUUM BOOSTER ASSEMBLY





Disassembly Steps
1. Clevis; Yoke
2. Nut; VLV rod
3. Retainer; Guard
4. Guard; VLV body
5. Silencer
6. Filter








BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

5C-64 BRAKES
REASSEMBLY
VACUUM BOOSTER ASSEMBLY




Reassembly Steps
1. Filter
2. Silencer
3. Guard; VLV body
▲ 4. Retainer; Guard
▲ 5. Nut; VLV rod
▲ 6. Clevis; Yoke


RTW 75CSH002901



Important Operations
4. Retainer; Guard
Ensure that the lug of the inner surface is fitted into the groove
of the ROD.

5. Nut; VLV Rod
Install the nut.

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

BRAKES 5C-65
RTW 75CSH002801
6. Clevis; Yoke
Assemble such that the distance from the rear of the vacuum
booster assembly to the center of the clevis yoke hole is within
the range of the reference values.
Distance mm (in)
RHD 147.9 - 148.9 (5.823 - 5.862)
L LHD 160.7 - 161.7 (6.327 - 6.366)
Upon assembling the clevis yoke, tighten the nut to the
specified torque.
Torque N ⋅m (kgf ⋅m/lb ⋅ft)
15 - 25 (1.5 - 2.5 / 11 - 18)



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

5C-66 BRAKES
4JA1-T/4JH1-TC RHD MODEL



RTW 75CMF001101
4JJ1-TC/4JK1-TC RHD MODEL



RTW 75CMF001301

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

BRAKES 5C-67
C24SE RHD MODEL



RTW 75CMF001401
HFV6 RHD MODEL



RTW 75CMF001601

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007