2007 ISUZU KB P190 ECO mode

UNIT REPAIR (AW30–40LE) 7A4–15
Major Components (3)
Major Components (3) and Associated Parts
RTW77ALF001801
EndOFCallout
Legend(1) Oil pump
(2) Race
(3) OD planetary gear and OD direct clutch
(4) Race
(5) OD planetary ring gear
(6) Snap ring
(7) Flange, plate and disc (B –0)
(8) Bearing and race
(9) Snap ring
(10) OD support
(11) Race
(12) Snap ring
(13) Second coast brake piston assembly
(14) Direct clutch and forward clutch (15) E-ring and pin
(16) Second coast brake band
(17) Front planetary ring gear
(18) Bearing and race
(19) Race
(20) Snap ring
(21) Front planetary gear
(22) Drum and one-way clutch
(23) Snap ring
(24) Flange, plate and disc (B –2)
(25) Snap ring
(26) Rear planetary gear, second brake drum and output shaft
(27) Bearing

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

UNIT REPAIR (AW30–40LE) 7A4–19
Install two removed bolts to the OD support, and
pull out the OD suppor t assembly.
252RY00005
12. Remove the race from OD support.
252RY00006
13. Check piston stroke of second coast brake (B –1)
Place a mark on the second coast brake piston rod
as shown in the figure.
Using feeler gauge, measure the stroke applying
the compressed air (390 – 780 kPa or 57 – 114 psi)
as shown in the figure.
Piston stroke: 1.5 – 3.0 mm (0.059 – 0.118 in)
If the values are nonstandard, replace piston rod
and recheck piston stroke.
If piston stroke is nonstandard, replace brake band. There are two piston rods.
248RY00004
248RY00005
Rod length 78.4 mm (3.09 in)
79.9 mm (3.15 in)

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

7A4–20 UNIT REPAIR (AW30–40LE)
14. Using snap ring pliers, remove the snap ring.
248RY00006
15. Applying compressed air to the oil hole, remove thesecond coast brake piston assembly.
248RY00007
16. Remove the direct clutch and forward clutch fromthe transmission case.
248RY00008
17. Remove the E-ring from the pin.Remove the pin from the brake band.
248RY00009

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

UNIT REPAIR (AW30–40LE) 7A4–21
18. Remove the second coast brake band from thetransmission case.
248RY00010
19. Remove the front planetary ring gear from thetransmission case.
247RY00004
20. Remove the bearing and race.
247RY00005
21. Remove the race.
247RY00006
22. Using snap ring pliers, remove the snap ring.
248RY00011

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

UNIT REPAIR (AW30–40LE) 7A4–23
27. Check pack clearance of first and reverse brake (B–
3)
Using a feeler gauge, measure the clearance
between the plate and second brake drum as shown
in the figure.
Clearance: 0.70 – 1.22 mm (0.0276 – 0.0480)
If the values are nonstandard, replace the discs.
248RY00016
28. Using snap ring pliers, remove the snap ring.
248RY00017
29. Remove the rear planetary gear, second brake drum and output shaft as an assembly.
247R200001
30. Remove the assembled thrust bearing and racefrom the transmission case.
248RY00018

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

7A4–24 UNIT REPAIR (AW30–40LE)
Reassembly
1. Coat the assembled bearing and race withpetroleum jelly and install it onto the transmission
case.
Assembled bearing and race (Reference)
247RY00008
2. Install the rear planetary gear, second brake drum and output shaft.
 Align the teeth of the second brake drum,
flanges, discs and plates as shown in the figure.
247RY00009
 Align the splines of the transmission case and the
assembled rear planetary gear, second brake
drum and output shaft, indicated by A in the
figure.
247RY00010
3. Using snap ring pliers, install the snap ring.
246RY00003
Bearing and race Diameter
Inside 39.38 mm (1.550 in)
Outside 58.15 mm (2.289 in)

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

UNIT REPAIR (AW30–40LE) 7A4–25
4. Check pack clearance of first and reverse brake.Using a thickness gauge, measure the clearance
between the plate and second brake drum as shown
in the figure.
Clearance: 0.70 – 1.22 mm (0.0276 – 0.0480 in)
If the values are nonstandard, check for an improper
installation.
248RY00016
5. Install second brake piston sleeve.
246RY00004
6. Install one-way clutch in the transmission case.
247RY00011
7. Install discs and plates (B –2).
Instal the 2.5 mm (0.098 in) thick plate with the
rounded edge side of the plate facing the disc.
Alternately install five discs and six plates (Disc first)
246RY00005

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

UNIT REPAIR (AW30–40LE) 7A4–27
11. Using snap ring pliers, install the snap ring.
248RY00011
12. Coat the bearing race with petroleum jelly and installit onto the front planetary gear.
Bearing race diameter (Reference)
247RY00014
13. Insert the second coast brake band to the transmission case.
248RY00010
14. Install the E-ring and pin.
Install the pin through the brake band.
248RY00021
Bearing race Diameter
Inside 34.3 mm (1.350 in)
Outside 47.8 mm (1.882 in)

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007