Page 107 of 6020
HEATER AND AIR CONDITIONING 1-73
DEFROSTER NOZZLE AND VENT DUCT
REMOVAL AND INSTALLATION
This illustration is based on RHD model
RTW 710MF000201
Removal Steps
1. Instrument panel assembly and cross beam
2. Side def hose RH/LH
3. Defroster nozzle
4. Vent duct driver side and assist side
5. Center vent duct
Installation Steps
5. Center vent duct
4. Vent duct driver side and assist side
3. Defroster nozzle
2. Side def hose RH/LH
1. Instrument panel assembly and cross beam
Important Operation - Removal
1. Instrument Panel Assembly and Cross Beam
Refer to SECTION 10 “INSTRUMENT PANEL”.
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 108 of 6020
1-74 HEATER AND AIR CONDITIONING
REAR HEATER DUCT
REMOVAL AND INSTALLATION
This illustration is based on RHD model
RTW 710LF004301
Disassembly Steps
1. Front seat assembly (RH/LH)
• Refer to SECTION 10 “FRONT
SEAT”.
2. Rear floor console
• Refer to SECTION 10 “FLOOR
CONSOLE”.
3. Front floor console (A/T, M/T Model)
• Refer to SECTION 10 “FLOOR
CONSOLE”.
4. Sill plate (RH/LH)
• Refer to SECTION 10 “INTERIOR
TRIM PANELS”.
5. Dash side trim cover (RH/LH)
6. Carpet
7. Clip
8. Rear Heater duct (RH/LH)
9. Rear Heater duct center
Reassembly Steps
9. Rear heater duct center
8. Rear heater duct (RH/LH)
7. Clip
6. Carpet
5. Dash side trim cover (RH/LH)
4. Sill plate (RH/LH)
• Refer to SECTION 10 “INTERIOR
TRIM PANELS”.
3. Front floor console (A/T, M/T Model)
• Refer to SECTION 10 “FLOOR
CONSOLE”.
2. Rear floor console
• Refer to SECTION 10 “FLOOR
CONSOLE”.
1. Front seat assembly (RH/LH)
• Refer to SECTION 10 “FRONT
SEAT”.
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 109 of 6020
HEATER AND AIR CONDITIONING 1-75
CONTROL LEVER ASSEMBLY
REMOVAL AND INSTALLATION
This illustration is based on RHD model
RTW 710MF000801
Removal Steps
1. Glove box
2. Instrument panel driver side lower cover
3. Ash-tray
4. Control cables
5. Center cluster
6. Attaching screw
7. A/C switch connector
8. Fan switch connector
9. Control lever assembly
Installation Steps
9. Control lever assembly
8. Fan switch connector
7. A/C switch connector
6. Attaching screw
5. Center cluster
4. Control cables
3. Ash-tray
2. Instrument panel driver side lower cover
1. Glove box
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 110 of 6020
1-76 HEATER AND AIR CONDITIONING
Important Operations - Removal
2. Instrument Panel Driver Lower Cover
Refer to SECTION 10 “INSTRUMENT PANEL” .
RTW 710SH000601
4. Control Cables
Disconnect control cables at each side of the unit.
5. Center Cluster
Refer to SECTION 10 “INSTRUMENT PANEL”.
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 111 of 6020
HEATER AND AIR CONDITIONING 1-77
Important Operations - Installation
9. Control Lever Assembly
Air source control cable
RHD
1) Slide the control lever to the left (“CIRC” position).
2) Connect the control cable at the "CIRC" position of the link unit of blower assembly and fix it with the clip.
LHD
1) Slide the control lever to the right (“FRESH” position).
2) Connect the control cable at the "FRESH" position of the link unit of blower assembly and fix it with the clip.
Temperature control cable
RHD
1) Turn the control knob to the right (“FULL HOT” position).
2) Connect the control cable at the “FULL HOT” position of the mix lever of the heater unit and fix it with the clip.
LHD
1) Turn the control knob to the left (“FULL COLD” position).
2) Connect the control cable at the “FULL COLD” position o
f
the mix lever of the heater unit and fix it with the clip.
Air select control cable
RHD
1) Turn the control knob to the left (“VENT” position).
2) Connect the control cable at the “VENT” position of the mode control link of the heater unit and fix it with the clip.
LHD
1) Turn the control knob to the right (“DEF” position).
2) Connect the control cable at the “DEF” position of the mode control link of the heater unit and fix it with the clip.
4. Control Cables
Check control cable operation
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 112 of 6020
1-78 HEATER AND AIR CONDITIONING
RTW 410MF000201
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 113 of 6020
HEATER AND AIR CONDITIONING 1-79
CONTROL PANEL ILLUMINATION BULB
REMOVAL AND INSTALLATION
This illustration is based on RHD model
RTW 710MF000401
Removal Steps
1. Control lever assembly
2. Illumination bulb
Installation Steps
2. Illumination bulb
1. Control lever assembly
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 114 of 6020
1-80 HEATER AND AIR CONDITIONING
RTW 710MH000101
Important Operations - Removal
1. Control lever assembly
Refer to “CONTROL LEVER ASSEMBLY” in this section.
2. Illumination Bulb
To remove the illumination bulb, insert a pliers (long nose) into
the cap at the back of the bulb. Turn the bulb counterclockwise
and pull it free.
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
