2007 INFINITI QX56 transmission

AT-72
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
32
Slips/Will
Not en-
gageWhen you press the
accelerator pedal and
shift speed D4 → D3
the engine idles or the
transmission slips.ON vehicle1. Fluid level and stateAT- 5 1
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 5,
AT- 1 2 4
3. ATF pressure switch 3 and input clutch solenoid valveAT- 1 5 2,
AT- 1 3 0
4. ATF pressure switch 1 and front brake solenoid valveAT- 1 5 0,
AT- 1 3 4
5. CAN communication lineAT- 9 1
6. Line pressure testAT- 5 1
7. Control valve with TCMAT- 2 1 0
OFF vehicle8. Torque converter AT- 2 4 0
9. Oil pump assemblyAT- 2 5 8
10. 3rd one-way clutchAT- 2 6 0
11. Gear systemAT- 2 2 8
12. High and low reverse clutchAT- 2 7 2
13. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to AT-
19, AT- 2 0.)AT- 2 4 0
14. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 9
, AT- 2 0.)AT- 2 4 0
33When you press the
accelerator pedal and
shift speed D3 → D2
the engine idles or the
transmission slips.ON vehicle1. Fluid level and stateAT- 5 1
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 5,
AT- 1 2 4
3. ATF pressure switch 6, high and low reverse clutch sole-
noid valveAT- 1 5 6,
AT- 1 4 2
4. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 5 4,
AT- 1 3 8
5. CAN communication lineAT- 9 1
6. Line pressure testAT- 5 1
7. Control valve with TCMAT- 2 1 0
OFF vehicle8. Torque converterAT- 2 4 0
9. Oil pump assemblyAT- 2 5 8
10. 3rd one-way clutchAT- 2 6 0
11. Gear systemAT- 2 2 8
12. Direct clutchAT- 2 7 4
13. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 9
, AT- 2 0.)AT- 2 4 0
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-73
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
AT
N
O
P
34
Slips/Will
Not En-
gageWhen you press the
accelerator pedal and
shift speed D2 → D1
the engine idles or the
transmission slips.ON vehicle1. Fluid level and stateAT- 5 1
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 5,
AT-124
3. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 5 4,
AT-138
4. CAN communication lineAT- 9 1
5. Line pressure testAT- 5 1
6. Control valve with TCMAT-210
OFF vehicle7. Torque converterAT-240
8. Oil pump assemblyAT-258
9. 3rd one-way clutchAT-260
10. 1st one-way clutchAT-267
11. Gear systemAT-228
12. Reverse brakeAT-240
13. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to AT-
19, AT- 2 0.)AT-240
14. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 9
, AT- 2 0.)AT-240
35With selector lever in
“D” position, accelera-
tion is extremely poor.ON vehicle1. Fluid level and stateAT- 5 1
2. Line pressure testAT- 5 1
3. Accelerator pedal position sensorAT- 11 7
4. CAN communication lineAT- 9 1
5. PNP switchAT- 9 9
6. Control cable adjustmentAT-208
7. Control valve with TCMAT-210
OFF vehicle8. Torque converterAT-240
9. Oil pump assemblyAT-258
10. 1st one-way clutchAT-267
11. Gear systemAT-228
12. Reverse brakeAT-240
13. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to AT-
19, AT- 2 0.)AT-240
14. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 9
, AT- 2 0.)AT-240
No. Items Symptom Condition Diagnostic ItemReference
page

AT-80
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
56
OthersMaximum speed low.ON vehicle1. Fluid level and stateAT- 5 1
2. Line pressure testAT- 5 1
3. Accelerator pedal position sensorAT- 11 7
4. CAN communication lineAT- 9 1
5. Direct clutch solenoid valveAT- 1 3 8
6. Control valve with TCMAT- 2 1 0
OFF vehicle7. Torque converterAT- 2 4 0
8. Oil pump assemblyAT- 2 5 8
9. Input clutchAT- 2 6 2
10. Gear systemAT- 2 2 8
11. High and low reverse clutchAT- 2 7 2
12. Direct clutchAT- 2 7 4
13. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to AT-
19, AT- 2 0.)AT- 2 4 0
14 Forward brake (Parts behind drum support is impossible to
perform inspection by disassembly. Refer to AT- 1 9
, AT- 2 0.)AT- 2 4 0
57 Extremely large creep.ON vehicle1. Engine idle speed EC-75

2. CAN communication lineAT- 9 1
3. ATF pressure switch 5AT- 1 5 4
OFF vehicle 4. Torque converterAT- 2 4 0
58With selector lever in
“P” position, vehicle
does not enter parking
condition or, with se-
lector lever in another
position, parking con-
dition is not cancelled.
Refer to AT-168, "
In
"P" Position, Vehicle
Moves When
Pushed".ON vehicle1. PNP switchAT- 9 9
2. Control cable adjustmentAT- 2 0 8
OFF vehicle 3. Parking pawl componentsAT- 2 2 8
59Vehicle runs with
transmission in “P” po-
sition.ON vehicle1. PNP switchAT- 9 9
2. Fluid level and stateAT- 5 1
3. Control cable adjustmentAT- 2 0 8
4. Control valve with TCMAT- 2 1 0
5. Parking pawl componentsAT- 2 2 8
OFF vehicle 6. Gear systemAT- 2 2 8
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-81
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
AT
N
O
P
60
OthersVehicle runs with
transmission in “N” po-
sition.
Refer to AT- 1 6 9 , "In
"N" Position, Vehicle
Moves".ON vehicle1. PNP switchAT- 9 9
2. Fluid level and stateAT- 5 1
3. Control cable adjustmentAT-208
4. Control valve with TCMAT-210
OFF vehicle5. Input clutchAT-262
6. Gear systemAT-228
7. Direct clutchAT-274
8. Reverse brakeAT-240
9. Forward one- way clutch (Parts behind drum support is im-
possible to perform inspection by disassembly. Refer to AT-
19, AT- 2 0.)AT-240
10. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 9
, AT- 2 0.)AT-240
61Engine does not start
in “N” or “P” position.
Refer to AT- 1 6 8 , "En-
gine Cannot Be Start-
ed in "P" or "N"
Position".ON vehicle1. Ignition switch and starterPG-3
, SC-
9
2. Control cable adjustmentAT-208
3. PNP switchAT- 9 9
62Engine starts in posi-
tions other than “N” or
“P”.ON vehicle1. Ignition switch and starterPG-3
, SC-
9
2. Control cable adjustmentAT-208
3. PNP switchAT- 9 9
63 Engine stall.ON vehicle1. Fluid level and stateAT- 5 1
2. Engine speed signalAT-109
3. Turbine revolution sensorAT-103
4. Torque converter clutch solenoid valveAT- 111
5. CAN communication lineAT- 9 1
6. Control valve with TCMAT-210
OFF vehicle 7. Torque converterAT-240
64Engine stalls when se-
lect lever shifted “N” →
“D”, “R”.ON vehicle1. Fluid level and stateAT- 5 1
2. Engine speed signalAT-109
3. Turbine revolution sensorAT-103
4. Torque converter clutch solenoid valveAT- 111
5. CAN communication lineAT- 9 1
6. Control valve with TCMAT-210
OFF vehicle 7. Torque converterAT-240
No. Items Symptom Condition Diagnostic ItemReference
page

DTC U1000 CAN COMMUNICATION LINE
AT-91
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
AT
N
O
P
DTC U1000 CAN COMMUNICATION LINE
DescriptionINFOID:0000000003532260
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent malfunction detection ability.
Many electronic control units are equipped onto a vehicle, and each control unit shares information and links
with other control units during operation (not independent). In CAN communication, control units are con-
nected with 2 communication lines (CAN H line, CAN L line) allowing a high rate of information transmission
with less wiring. Each control unit transmits/receives data but selectively reads required data only.
On Board Diagnosis LogicINFOID:0000000003532261
• This is an OBD-II self-diagnostic item.
• Diagnostic trouble code “U1000 CAN COMM CIRCUIT” with CONSULT-II is detected when TCM cannot
communicate to other control units.
Possible CauseINFOID:0000000003532262
Harness or connectors
(CAN communication line is open or shorted.)
DTC Confirmation ProcedureINFOID:0000000003532263
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “DATA MONITOR” mode for “ENGINE” with CONSULT-II.
3. Start engine and wait for at least 6 seconds.
4. If DTC is detected, go to AT-93, "
Diagnosis Procedure".
WITH GST
Follow the procedure “WITH CONSULT-II”.
BCIA0031E

DTC P0705 PARK/NEUTRAL POSITION SWITCH
AT-99
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
AT
N
O
P
DTC P0705 PARK/NEUTRAL POSITION SWITCH
DescriptionINFOID:0000000003532278
• The park/neutral position (PNP) switch includes a transmission position switch.
• The transmission range switch detects the selector lever position and sends a signal to the TCM.
CONSULT-II Reference Value in Data Monitor ModeINFOID:0000000003532279
On Board Diagnosis LogicINFOID:0000000003532280
• This is an OBD-II self-diagnostic item.
• Diagnostic trouble code “P0705 PNP SW/CIRC” with CONSULT-II is detected under the following condi-
tions.
- When TCM does not receive the correct voltage signal from the PNP switch 1, 2, 3, 4 based on the gear
position.
- When no other position but “P” position is detected from “N” positions.
Possible CauseINFOID:0000000003532281
• Harness or connectors
[The park/neutral position (PNP) switch 1, 2, 3, 4 and TCM circuit is open or shorted.]
• Park/neutral position (PNP) switch 1, 2, 3, 4
DTC Confirmation ProcedureINFOID:0000000003532282
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “DATA MONITOR” mode for “ENGINE” with CONSULT-II.
3. Start engine.
4. Drive vehicle and maintain the following conditions for at least 2
consecutive seconds.
THRTL POS SEN: More than 1.2V
5. If DTC is detected, go to AT-100, "
Diagnosis Procedure".
WITH GST
Follow the procedure “With CONSULT-II”.
Item name Condition Display value
SLCTLVR POSI Selector lever in “N”,“P” positions. N/P
Selector lever in “R” position. R
Selector lever in “D” position. D
Selector lever in “4” position. 4
Selector lever in “3” position. 3
Selector lever in “2” position. 2
Selector lever in “1” position. 1
BCIA0031E

DTC P0717 TURBINE REVOLUTION SENSOR
AT-103
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
AT
N
O
P
DTC P0717 TURBINE REVOLUTION SENSOR
DescriptionINFOID:0000000003532285
The turbine revolution sensor detects input shaft rpm (revolutions per minute). It is located on the input side of
the automatic transmission. Monitors revolution of sensor 1 and sensor 2 for non-standard conditions.
CONSULT-II Reference Value in Data Monitor ModeINFOID:0000000003532286
On Board Diagnosis LogicINFOID:0000000003532287
• This is an OBD-II self-diagnostic item.
• Diagnostic trouble code “P0717 TURBINE REV S/CIRC” with CONSULT-II is detected under the following
conditions.
- When TCM does not receive the proper voltage signal from the sensor.
- When TCM detects an irregularity only at position of 4th gear for turbine revolution sensor 2.
Possible CauseINFOID:0000000003532288
• Harness or connectors
(The sensor circuit is open or shorted.)
• Turbine revolution sensor 1, 2
DTC Confirmation ProcedureINFOID:0000000003532289
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “DATA MONITOR” mode for “A/T” with CONSULT-II.
3. Start engine and maintain the following conditions for at least 5
consecutive seconds.
VHCL SPEED SE: 40 km/h (25 MPH) or more
ENGINE SPEED: 1,500 rpm or more
ACCELE POS: 0.5/8 or more
Selector lever: “D” position
Gear position (Turbine revolution sensor 1): 4th or 5th posi-
tion
Gear position (Turbine revolution sensor 2): All position
Driving location: Driving the vehicle uphill (increased
engine load) will help maintain the driving conditions required for this test.
4. If DTC is detected, go to AT-103, "
Diagnosis Procedure".
WITH GST
Follow the procedure “With CONSULT-II”.
Diagnosis ProcedureINFOID:0000000003532290
1.CHECK INPUT SIGNAL
With CONSULT-II
Item name Condition Display value (rpm)
TURBINE REV During driving (lock-up ON) Approximately matches the engine speed.
BCIA0031E

TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-169
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
AT
N
O
P
Even though the selector lever is set in the “P” position, the parking mechanism is not actuated,
allowing the vehicle to be moved when it is pushed.
DIAGNOSTIC PROCEDURE
1.CHECK PNP SWITCH CIRCUIT
Perform self-diagnosis. Refer to AT-83, "
CONSULT-II Function (A/T)".
Do the self-diagnosis results indicate PNP switch?
YES >> Check the malfunctioning system. Refer to AT- 9 9.
NO >> GO TO 2.
2.CHECK CONTROL CABLE
Check the control cable.
• Refer to AT-208, "
Checking of A/T Position".
OK or NG
OK >> GO TO 3.
NG >> Adjust control cable. Refer to AT-208, "
Adjustment of A/
T Position".
3.CHECK A/T FLUID CONDITION
1. Remove oil pan. Refer to AT-210, "
Control Valve with TCM and A/T Fluid Temperature Sensor 2".
2. Check A/T fluid condition. Refer to AT-13, "
Checking Automatic
Transmission Fluid (ATF)".
OK or NG
OK >>INSPECTION END
NG >> GO TO 4.
4.DETECT MALFUNCTIONING ITEM
• Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to AT-60,
"Symptom Chart" (Symptom No.58).
OK or NG
OK >>INSPECTION END
NG >> Repair or replace damaged parts.
In "N" Position, Vehicle MovesINFOID:0000000003532451
SYMPTOM:
Vehicle moves forward or backward when selecting “N” position.
DIAGNOSTIC PROCEDURE
1.CHECK PNP SWITCH CIRCUIT
Perform self-diagnosis. Refer to AT-83, "
CONSULT-II Function (A/T)".
Do the self-diagnostic results indicate PNP switch?
YES >> Check the malfunctioning system. Refer to AT- 9 9.
NO >> GO TO 2.
2.CHECK CONTROL CABLE
LCIA0345E
SCIA5199E