2007 INFINITI QX56 ignition

AV-124
< SERVICE INFORMATION >
NAVIGATION SYSTEM
2.CHECK 2: DVD-ROM
Check DVD-ROM for dirt, scratches and warpage.
OK or NG
OK >> GO TO 3.
NG >> Replace DVD-ROM map.
3.CHECK 3: DVD-ROM
Insert same DVD-ROM to make sure same diagnosis result is found as last self-diagnosis.
OK or NG
OK >> Replace NAVI control unit. Refer to AV-145, "Removal and Installation".
NG >> Replace DVD-ROM map.
If Connection Between NAVI Control Unit and GPS Antenna Is Malfunctioning
INFOID:0000000003533743
1.CHECK GPS ANTENNA
Check cable for GPS antenna for damage.
OK or NG
OK >> GO TO 2.
NG >> Replace GPS antenna. Refer to AV-145, "
Removal and Installation".
2.CHECK BY REPLACEMENT OF GPS ANTENNA
Replace with other functional GPS antenna to try self-diagnosis again.
Result of self-diagnosis; Found same result?
YES >> Replace NAVI control unit. Refer to AV-145, "Removal and Installation".
NO >> Replace GPS antenna. Refer to AV-145, "
Removal and Installation".
Operating Screen for Audio and A/C Is Not Displayed When Showing NAVI Screen
INFOID:0000000003533744
1.CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect display control unit connector M95 and display unit
connector M93.
3. Check continuity between display control unit harness connector
M95 terminal 49, 51, 53, 55 and display unit harness connector
M93 terminal 21, 9, 20, 8.
4. Check continuity between display control unit harness connector
M95 terminal 49, 51, 53, 55 and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness.
2.CHECK HORIZONTAL SYNCHRONIZATION SIGNALContinuity should exist.
Continuity should not exist.
WKIA1965E

NAVIGATION SYSTEM
AV-125
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
MA
B
AV
N
O
P
1. Connect display control unit connector and display unit connec-
tor.
2. Turn ignition switch ON.
3. Check signal between display control unit connector M95 termi-
nals 55 and 49 with CONSULT-ll or oscilloscope.
OK or NG
OK >> GO TO 3.
NG >> Replace display unit. Refer to AV-145, "
Removal and
Installation".
3.CHECK VERTICAL SYNCHRONIZATION SIGNAL
1. Turn ignition switch ON.
2. Check signal between display control unit connector M95 termi-
nals 53 and 49 with CONSULT-ll or oscilloscope.
OK or NG
OK >> GO TO 4.
NG >> Replace display unit. Refer to AV-145, "
Removal and
Installation".
4.CHECK RGB AREA SIGNAL
1. Press the “TRIP” button.
2. Check signal between display control unit connector M95 termi-
nals 51 and 49 with CONSULT-ll or oscilloscope.
OK or NG
OK >> Replace display unit. Refer to AV-145, "Removal and
Installation".
NG >> Replace display control unit. Refer to AV-145, "
Removal
and Installation".
Color of RGB Image Is Not Proper (Only NAVI Screen Looks Bluish)INFOID:0000000003533745
1.CHECK RGB HARNESS
1. Turn ignition switch OFF.
2. Disconnect NAVI control unit connector B152 and display control unit connector M95.
3. Check continuity between NAVI control unit and display control unit.
4. Check continuity between NAVI control unit and ground.
•When the screen looks bluish.55 - 49 : Refer to AV-91, "
Terminal and Reference
Value for Display Control unit".
SKIA4305E
53 - 49 : Refer to AV-91, "Terminal and Reference
Value for Display Control unit".
WKIA1773E
51 - 49 : Refer to AV-91, "Terminal and Reference
Value for Display Control unit".
SKIA4306E
Te r m i n a l s
Continuity BA
Connector Terminal Connector Terminal
NAVI control
unit: B15244
Display control
unit: M9544
Ye s
47 45
WKIA4215E

AV-126
< SERVICE INFORMATION >
NAVIGATION SYSTEM
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2.CHECK RGB SIGNAL
1. Connect NAVI control unit connector and display control unit
connector.
2. Turn ignition switch ON.
3. Display “Color bar” by “CONFIRMATION/ADJUSTMENT” mode.
4. Check signal between NAVI control unit connector B152 termi-
nal 44 and 47 with CONSULT-ll or oscilloscope.
•When the screen looks bluish.
Voltage signal between NAVI control unit connector B152 terminal
44 and 47.
OK or NG
OK >> Replace display control unit. Refer to AV-145, "Removal and Installation".
NG >> Replace NAVI control unit. Refer to AV-145, "
Removal and Installation".
Color of RGB Image Is Not Proper (Only NAVI Screen Looks Reddish)INFOID:0000000003533746
1.CHECK RGB HARNESS
1. Turn ignition switch OFF.
2. Disconnect NAVI control unit connector B152 and display control unit connector M95.
3. Check continuity between NAVI control unit and display control unit.
4. Check continuity between NAVI control unit and ground.
•When the screen looks reddish.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2.CHECK RGB SIGNAL
Terminals
Continuity B
—
Connector Terminal
NAVI control unit:
B15244
Ground No
47
44 - 47 : Refer to AV-89, "Terminal
and Reference Value for
NAVI Control Unit".
WKIA4216E
Te r m i n a l s
Continuity BA
Connector Terminal Connector Terminal
NAVI control
unit: B15245 Display control
unit:
M9546
Ye s
47 45
Te r m i n a l s
Continuity B
—
Connector Terminal
NAVI control unit:
B15245
Ground No
47
WKIA4217E

NAVIGATION SYSTEM
AV-127
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
MA
B
AV
N
O
P
1. Connect NAVI control unit connector and display control unit
connector.
2. Turn ignition switch ON.
3. Display ″Color bar″ by ″CONFIRMATION/ADJUSTMENT″
mode.
4. Check signal between NAVI control unit connector B152 termi-
nal 45 and 47 with CONSULT-ll or oscilloscope.
•When the screen looks reddish.
Voltage signal between NAVI control unit connector B152 terminal
45 and 47.
OK or NG
OK >> Replace display control unit. Refer to AV-145, "Removal and Installation".
NG >> Replace NAVI control unit. Refer to AV-145, "
Removal and Installation".
Color of RGB Image Is Not Proper (Only NAVI Screen Looks Yellowish)INFOID:0000000003533747
1.CHECK RGB HARNESS
1. Turn ignition switch OFF.
2. Disconnect NAVI control unit connector B152 and display control unit connector M95.
3. Check continuity between NAVI control unit and display control unit.
4. Check continuity between NAVI control unit and ground.
•When the screen looks yellowish.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2.CHECK RGB SIGNAL45 - 47 : Refer to AV-89, "
Terminal
and Reference Value for
NAVI Control Unit".
WKIA4218E
Te r m i n a l s
Continuity BA
Connector Terminal Connector Terminal
NAVI control
unit: B15246 Display control
unit:
M9548
Ye s
47 45
Te r m i n a l s
Continuity B
—
Connector Terminal
NAVI control unit:
B15246
Ground No
47
WKIA4219E

AV-128
< SERVICE INFORMATION >
NAVIGATION SYSTEM
1. Connect NAVI control unit connector and display control unit
connector.
2. Turn ignition switch ON.
3. Display ″Color bar″ by ″CONFIRMATION/ADJUSTMENT″
mode.
4. Check signal between NAVI control unit connector B152 termi-
nal 46 and 47 with CONSULT-ll or oscilloscope.
•When the screen looks yellowish.
Voltage signal between NAVI control unit connector B152 terminal
46 and 47.
OK or NG
OK >> Replace display control unit. Refer to AV-145, "Removal and Installation".
NG >> Replace NAVI control unit. Refer to AV-145, "
Removal and Installation".
Color of RGB Image Is Not Proper (All Screens Look Bluish)INFOID:0000000003533748
1.CHECK RGB HARNESS
1. Turn ignition switch OFF.
2. Disconnect display control unit connector M95 and display unit connector M93.
3. Check continuity between display control unit and display unit.
4. Check continuity between display control unit and ground.
•When the screen looks bluish.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2.CHECK RGB SIGNAL
1. Connect display control unit connector M95 and display unit
connector M93.
2. Turn ignition switch ON.
3. Display “Color bar” by “CONFIRMATION/ADJUSTMENT” mode.
4. Check the following with CONSULT-ll or oscilloscope.
•When the screen looks bluish.
Voltage signal between display control unit connector M95 terminal
50 and 47.46 - 47 : Refer to AV-89, "
Terminal
and Reference Value for
NAVI Control Unit".
WKIA4220E
Te r m i n a l s
Continuity Display control unit Display unit
Connector Terminal Connector Terminal
M9550
M9317
Ye s
47 7
Te r m i n a l s
Continuity Display control unit
—
Connector Terminal
M9550
Ground No
47
SKIA4353E
50 - 47 : Refer to AV-91, "Terminal
and Reference Value for Dis-
play Control unit".SKIA4697E

NAVIGATION SYSTEM
AV-129
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
MA
B
AV
N
O
P
OK or NG
OK >> Replace display unit. Refer to AV-145, "Removal and Installation".
NG >> Replace display control unit. Refer to AV-145, "
Removal and Installation".
Color of RGB Image Is Not Proper (All Screens Look Reddish)INFOID:0000000003533749
1.CHECK RGB HARNESS
1. Turn ignition switch OFF.
2. Disconnect display control unit connector M95 and display unit connector M93.
3. Check continuity between display control unit and display unit.
4. Check continuity between display control unit and ground.
•When the screen looks reddish.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2.CHECK RGB SIGNAL
1. Connect display control unit connector M95 and display unit
connector M93.
2. Turn ignition switch ON.
3. Display “Color bar” by “CONFIRMATION/ADJUSTMENT” mode.
4. Check the following with CONSULT-ll or oscilloscope.
•When the screen looks reddish.
Voltage signal between display control unit connector M95 terminal
52 and 47.
OK or NG
OK >> Replace display unit. Refer to AV-145, "Removal and Installation".
NG >> Replace display control unit. Refer to AV-145, "
Removal and Installation".
Color of RGB Image Is Not Proper (All Screens Look Yellowish)INFOID:0000000003533750
1.CHECK RGB HARNESS
1. Turn ignition switch OFF.
2. Disconnect display control unit connector M95 and display unit connector M93.
3. Check continuity between display control unit and display unit.
4. Check continuity between display control unit and ground.
•When the screen looks yellowish.
Te r m i n a l s
Continuity Display control unit Display unit
Connector Terminal Connector Terminal
M9552
M936
Ye s
47 7
Te r m i n a l s
Continuity Display control unit
—
Connector Terminal
M9552
Ground No
47
SKIA4354E
52 - 47 : Refer to AV-91, "Terminal
and Reference Value for Dis-
play Control unit".SKIA4698E

AV-130
< SERVICE INFORMATION >
NAVIGATION SYSTEM
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2.CHECK RGB SIGNAL
1. Connect display control unit connector M95 and display unit
connector M93.
2. Turn ignition switch ON.
3. Display “Color bar” by “CONFIRMATION/ADJUSTMENT” mode.
4. Check the following with CONSULT-ll or oscilloscope.
•When the screen looks yellowish.
Voltage signal between display control unit connector M95 terminal
54 and 47.
OK or NG
OK >> Replace display unit. Refer to AV-145, "Removal and Installation".
NG >> Replace display control unit. Refer to AV-145, "
Removal and Installation".
NAVI Screen Is RollingINFOID:0000000003533751
1.CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect NAVI control unit connector B152 and display control unit connector M95.
3. Check continuity between NAVI control unit and display control unit.
4. Check continuity between NAVI control unit and ground.
Te r m i n a l s
Continuity Display control unit Display unit
Connector Terminal Connector Terminal
M9554
M9318
Ye s
47 7
Te r m i n a l s
Continuity Display control unit
—
Connector Terminal
M9554
Ground No
47
SKIA4355E
54 - 47 : Refer to AV-91, "Terminal
and Reference Value for Dis-
play Control unit".SKIA4356E
Te r m i n a l s
Continuity BA
Connector Terminal Connector Terminal
NAVI control
unit: B15248 Display control
unit:
M9543
Ye s
49 41
Te r m i n a l s
Continuity B
—
Connector Terminal
NAVI control unit:
B15248
Ground No
49
WKIA4224E

NAVIGATION SYSTEM
AV-131
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
MA
B
AV
N
O
P
OK or NG
OK >> GO TO 2.
NG >> Repair harness.
2.CHECK RGB SYNCHRONIZING SIGNAL
1. Connect NAVI control unit connector and display control unit
connector.
2. Turn ignition switch ON.
3. Check signal between NAVI control unit connector M95 termi-
nals 48 and 49 with CONSULT-ll or oscilloscope.
OK or NG
OK >> GO TO 3.
NG >> Replace NAVI control unit. Refer to AV-145, "
Removal and Installation".
3.CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect display control unit connector M95 and display unit connector M93.
3. Check continuity between display control unit and display unit.
4. Check continuity between display control unit and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair harness.
4.CHECK RGB SYNCHRONIZING SIGNAL
1. Connect display control unit connector and display unit connec-
tor.
2. Turn ignition switch ON.
3. Check signal between display unit connector M93 terminals 19
and 21 with CONSULT-ll or oscilloscope.
OK or NG
OK >> Replace display unit. Refer to AV-145, "Removal and
Installation".
NG >> Replace display control unit. Refer to .48 - 49 : Refer to AV-89, "
Terminal
and Reference Value for NAVI
Control Unit".
WKIA4225E
Te r m i n a l s
Continuity Display control unit Display unit
Connector Terminal Connector Terminal
M9556
M9319
Ye s
49 21
Te r m i n a l s
Continuity Display control unit
—
Connector Terminal
M9556
Ground No
49
WKIA2775E
19 - 21 : Refer to AV-91, "Terminal
and Reference Value for Dis-
play Control unit".
WKIA2022E