2007 INFINITI M35 service

PRECAUTIONS
TF-3
C
E
F
G
H
I
J
K
L
MA
B
TF
Revision: 2007 April2007 M35/M45
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NDS000D3
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
PrecautionsNDS000D4

Before connecting or disconnecting the AWD control unit
harness connector, turn ignition switch “OFF” and discon-
nect battery ground cable. Because battery voltage is
applied to AWD control unit even if ignition switch is turned
“OFF”.

When connecting or disconnecting pin connectors into or
from AWD control unit, take care not to damage pin termi-
nals (bend or break).
When connecting pin connectors, make sure that there are
no bends or breaks on AWD control unit pin terminal.

Before replacing AWD control unit, perform AWD control
unit input/output signal inspection and make sure whether
AWD control unit functions properly or not. Refer to TF-20,
"AWD Control Unit Input/Output Signal Reference Values" .
SEF289H
SEF291H
SDIA1848E

TF-4
PRECAUTIONS
Revision: 2007 April2007 M35/M45
Service Notice or PrecautionsNDS000D5

Do not reuse transfer fluid, once it has been drained.

Check the fluid level or replace the fluid only with the vehicle parked on level ground.

During removal or installation, keep inside of transfer clear of dust or dirt.

Replace all tires at the same time. Always use tires of the proper size and the same brand and pattern.
Fitting improper size and unusual wear tires applies excessive force to vehicle mechanism and can cause
longitudinal vibration.

Disassembly should be done in a clean work area, it is preferable to work in dustproof area.

Before proceeding with disassembly, thoroughly clean the transfer. It is important to prevent the internal
parts from becoming contaminated by dirt or other foreign matter.

All parts should be carefully cleaned with a general purpose, non-flammable solvent before inspection or
reassembly.

Check for the correct installation status prior to removal or disassembly. If matching marks are required,
be certain they do not interfere with the function of the parts when applied.

Check appearance of the disassembled parts for damage, deformation, and unusual wear. Replace them
with a new ones if necessary.

Gaskets, seals and O-rings should be replaced any time when the transfer is disassembled.

In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to outside. If
tightening sequence is specified, use it.

Observe the specified torque when assembling.

Clean and flush the parts sufficiently and blow-dry them.

Be careful not to damage sliding surfaces and mating surfaces.

Clean innerparts with lint-free cloth or towels. Do not use cotton work gloves and rags to prevent adhering
fibers.

PREPARATION
TF-5
C
E
F
G
H
I
J
K
L
MA
B
TF
Revision: 2007 April2007 M35/M45
PREPARATIONPFP:00002
Special Service ToolsNDS000D6
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool nameDescription
ST27862000
(—)
Drift
a: 62.5 mm (2.461 in) dia.
b: 42 mm (1.65 in) dia.

Installing front oil seal
KV381054S0
(J-34286)
Puller

Removing rear oil seal
ST30720000
(J-25405)
Drift
a: 77 mm (3.03 in) dia.
b: 55.5 mm (2.185 in) dia.

Installing rear oil seal

Installing mainshaft oil seal
KV40104830
(—)
Drift
a: 70 mm (2.76 in) dia.
b: 63.5 mm (2.500 in) dia.

Installing rear oil seal
KV38100300
(J-25523)
Drift
a: 54 mm (2.13 in) dia.
b: 46 mm (1.81 in) dia.
c: 32 mm (1.26 in) dia.

Removing mainshaft bearing
ST33052000
(—)
Drift
a: 28 mm (1.10 in) dia.
b: 22 mm (0.87 in) dia.

Removing mainshaft assembly
ST30611000
(J-25742-1)
Drift bar
a: 350 mm (1.10 in)
b: 25 mm (1.10 in) dia.
c: M12 × 1.5P

Removing rear bearing
ZZA0194D
ZZA0601D
ZZA0811D
ZZA1003D
ZZA1046D
ZZA1000D
NT663

PREPARATION
TF-7
C
E
F
G
H
I
J
K
L
MA
B
TF
Revision: 2007 April2007 M35/M45
Commercial Service ToolsNDS000D7
Tool nameDescription
Puller

Removing companion flange
Flange wrench

Removing and installing self-lock nut
Puller

Removing front drive shaft front bearing

Removing front drive shaft rear bearing
Power tool

Loosening bolts and nuts
NT077
NT771
ZZB0823D
PBIC0190E

SERVICE DATA AND SPECIFICATIONS (SDS)
TF-59
C
E
F
G
H
I
J
K
L
MA
B
TF
Revision: 2007 April2007 M35/M45
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
General SpecificationsNDS000E6
Applied model VQ35DE
Transfer model ETX13B
Fluid capacity (Approx.)
1.25 (2-5/8 US pt, 2-1/4 lmp pt)

TF-60
SERVICE DATA AND SPECIFICATIONS (SDS)
Revision: 2007 April2007 M35/M45

WT-1
ROAD WHEELS & TIRES
E SUSPENSION
CONTENTS
C
D
F
G
H
I
J
K
L
M
SECTION WT
A
B
WT
Revision: 2007 April2007 M35/M45
ROAD WHEELS & TIRES
PRECAUTIONS .......................................................... 3
Precautions .............................................................. 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
Commercial Service Tools ........................................ 4
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING ................................................ 5
NVH Troubleshooting Chart ..................................... 5
ROAD WHEEL ............................................................ 6
Inspection ................................................................. 6
ALUMINUM WHEEL ............................................. 6
STEEL WHEEL ..................................................... 6
ROAD WHEEL AND TIRE ASSEMBLY ..................... 7
Balancing Wheels (Bonding Weight Type) ............... 7
REMOVAL ............................................................. 7
WHEEL BALANCE ADJUSTMENT ...................... 7
Rotation .................................................................... 8
TIRE PRESSURE MONITORING SYSTEM ............... 9
System Components ................................................ 9
System Description .................................................. 9
TRANSMITTER ..................................................... 9
RECEIVER .......................................................... 10
LOW TIRE PRESSURE WARNING CONTROL
UNIT .................................................................... 10
LOW TIRE PRESSURE WARNING LAMP ......... 10
DISPLAY UNIT ..................................................... 11
Can Communication ................................................ 11
TROUBLE DIAGNOSES .......................................... 12
How to Perform Trouble Diagnoses ....................... 12
BASIC CONCEPT ............................................... 12
Schematic .............................................................. 13
Wiring Diagram — T/WARN — .............................. 14
Low Tire Pressure Warning Control Unit Input/Out-
put Signal Standard ................................................ 17
ID Registration Procedure ...................................... 18
ID REGISTRATION WITH ACTIVATION TOOL ... 18
ID REGISTRATION WITHOUT ACTIVATION
TOOL .................................................................. 18
Transmitter Wake Up Operation ............................. 19
WITH TRANSMITTER ACTIVATION TOOL ........ 19CONSULT-II Function (AIR PRESSURE MONI-
TOR) ....................................................................... 19
DESCRIPTION .................................................... 19
CONSULT-II SETTING PROCEDURE ................ 19
WORK SUPPORT MODE ................................... 20
SELF-DIAG RESULT MODE ............................... 20
DATA MONITOR MODE ...................................... 21
ACTIVE TEST MODE ......................................... 22
LOW TIRE PRESSURE WARNING CONTROL
UNIT PART NUMBER ......................................... 22
Diagnosis Procedure with Warning Lamp Function
(Without CONSULT-II) ............................................ 22
DESCRIPTION .................................................... 22
FUNCTION .......................................................... 22
LOW TIRE PRESSURE WARNING LAMP DIAG-
NOSTIC CHART .................................................. 23
How to Perform Trouble Diagnosis for Quick and
Accurate Repair ...................................................... 25
INTRODUCTION ................................................. 25
WORK FLOW ...................................................... 25
Preliminary Check .................................................. 26
Trouble Diagnosis Chart ......................................... 27
SELF-DIAGNOSIS .............................................. 27
DIAGNOSIS CHART BY SYMPTOM .................. 28
TROUBLE DIAGNOSIS FOR SYSTEM .................... 29
Transmitter no Data ................................................ 29
MALFUNCTION CODE NO. 21, 22, 23, 24 ......... 29
Receiver Data Error ................................................ 30
MALFUNCTION CODE NO. 25, 26, 27, 28 ......... 30
Transmitter Pressure Data Error ............................. 31
MALFUNCTION CODE NO. 35, 36, 37, 38 ......... 31
Transmitter Function Code Error ............................ 32
MALFUNCTION CODE NO. 41, 42, 43, 44 ......... 32
Transmitter Battery Voltage Low ............................. 32
MALFUNCTION CODE NO. 45, 46, 47, 48 ......... 32
Receiver ID No Registration ................................... 33
MALFUNCTION CODE NO. 51 ........................... 33
Vehicle Speed Signal .............................................. 33
MALFUNCTION CODE NO. 52 ........................... 33
Control Unit (EEPROM) Malfunction ...................... 34

WT-2Revision: 2007 April2007 M35/M45 MALFUNCTION CODE NO. 54 ........................... 34
CAN Communication System Malfunction .............. 34
TROUBLE DIAGNOSIS FOR SYMPTOMS .............. 35
Warning Lamp Does Not Come On When Ignition
Switch Is Turned ON ............................................... 35
Warning Lamp Stay On When Ignition Switch Is
Turned ON .............................................................. 35
Warning Lamp Blinks 1 Minute and Then Turns ON
When Ignition Switch Is Turned ON ........................ 36
Warning Lamp Blinks When Ignition Switch Is
Turned ON .............................................................. 37
Turn Signal Lamp Blinks When Ignition Switch Is
Turned ON .............................................................. 38
ID Registration Can Not Be Completed .................. 38REMOVAL AND INSTALLATION .............................. 39
Transmitter .............................................................. 39
REMOVAL ............................................................ 39
INSTALLATION .................................................... 39
Low Tire Pressure Warning Control Unit ................. 40
REMOVAL ............................................................ 40
INSTALLATION .................................................... 40
Receiver .................................................................. 40
REMOVAL ............................................................ 40
INSTALLATION .................................................... 40
SERVICE DATA AND SPECIFICATIONS (SDS) ...... 41
Road Wheel ............................................................ 41
Tire .......................................................................... 41