2007 INFINITI M35 warning

TROUBLE DIAGNOSIS
SRS-41
C
D
E
F
G
I
J
K
L
MA
B
SRS
Revision: 2007 April2007 M35/M45
Trouble Diagnosis: Passenger Seatbelt Warning SystemNHS0009S
1. CHECK THE SYSTEM 1
Check seatbelt warning lamp function.
Seatbelt warning lamp turns ON in the following conditions.

Driver seatbelt is fastened.

Occupant is on passenger seat.

Passenger seatbelt is not fasten.
OK or NG
OK >> GO TO 2.
NG >> Check the followings.

Harness between air bag diagnosis sensor unit and combination meter.

Seatbelt buckle switch (passenger side) circuit.

Seatbelt buckle switch (passenger side).
If these are OK, replace air bag diagnosis sensor unit.
2. CHECK THE SYSTEM 2
Check seatbelt warning lamp function.
Seatbelt warning lamp turns OFF in the following conditions.

Driver seatbelt is fastened.

Occupant is on passenger seat.

Passenger seatbelt is fastened.
OK or NG
OK >> System is OK.
NG >> Check the followings.

Seatbelt buckle switch (passenger side) circuit.

Seatbelt buckle switch (passenger side).
If these are OK, replace air bag diagnosis sensor unit.

DRIVER AIR BAG MODULE
SRS-43
C
D
E
F
G
I
J
K
L
MA
B
SRS
Revision: 2007 April2007 M35/M45
INSTALLATION
Install in the reverse order of removal.
CAUTION:

Fix the air bag module harness (shown as A in the figure) to
the harness fixing hook (shown as B in the figure).

Be careful not to damage the harness while installing.

Tighten the special bolts after exactly adjusting the centers of fixing holes on the air bag module
side and the steering wheel side. If the holes are misaligned, the bolt threads are damaged and the
module is not installed securely.

After the work is completed, make sure no system malfunction is detected by air bag warning
lamp.

In case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis func-
tion and delete the memory by CONSOULT–II.

In case that malunction is still detected after the above operation, peform self-diagnosis to repair
malfunctions. Refer to SRS-20, "
SRS Operation Check" .
PHIA0885J

SPIRAL CABLE
SRS-45
C
D
E
F
G
I
J
K
L
MA
B
SRS
Revision: 2007 April2007 M35/M45
CAUTION:

The spiral cable may snap by steering operation if the cable
is installed in an improper position.

The neutral position is set as follows.
Turn quietly the spiral cable clockwise to the end position.
Then turn it counterclockwise (about 2 and harf turns) and
stop turning at the point on which the stopper insertion
holes are in the same position.
The service part is installed in the neutral position by the
stopper and can be set without adjusting after the stopper
is removed.

Do not turn the spiral cable rashly and also beyond the limit
number of turns. (These will cause cable snap.)

Adjust the spiral cable locating pin (showed as A inthe fig-
ure) to the steering wheel locating pin hole (showed as C in
the figuer).

Secure the air bag harness with the harness fixing hook.

After the work is completed, make sure no system malfunc-
tion is detected by air bag warning lamp.

In case that malfunction is detected by the air bag warning
lamp, reset by the self-diagnosis function and delete the
memory by CONSULT−II.

In case that malfunction is still detected after the above
operation, perform self-diagnosis to repair malfunctions.
Refer to SRS-20, "
SRS Operation Check" .
PHIA0887J

SRS-46
FRONT PASSENGER AIR BAG MODULE
Revision: 2007 April2007 M35/M45
FRONT PASSENGER AIR BAG MODULEPFP:K8515
Removal and InstallationNHS0009E
REMOVAL
CAUTION:

Before servicing, turn ignition switch OFF, disconnect both battery terminal and wait at
least 3 minutes.

Do not use air tools or electric tools for servicing.

Always work from the side of air bag module. Do not work from the front of it.

Always place air bag module with pad side facing upward.

Do not use old fixing bolts after removal; replace with new bolts.

Do not make an impact to the air bag module by dropping etc. Replace the air bag module if it has
been dropped or sustained an impact.
1. Remove the instrument panel & pad assemblies. Refer to IP-10,
"INSTRUMENT PANEL ASSEMBLY" .
NOTE:
The figure shows installed condition of the front passenger air
bag module. (Under view of the module installed without glove
box cover.)
2. Remove the front passenger air bag module from the instrument panel & pad assemblies.

Remove the 2 screws.

Remove the air bag from the rear side hook. ( shows the
backward direction of the vehicle.)
INSTALLATION
Install in the reverse order of removal.
CAUTION:

Be careful not to damage the harness while installing.

After the work is completed, make sure no system malfunction is detected by air bag warning
lamp.

In case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis func-
tion and delete the memory by CONSOULT−II.

In case that malfunction is still detected after the above operation, peform self-diagnosis to repair
malfunctions. Refer to SRS-20, "
SRS Operation Check" . Passenger air bag module connector-A
Passenger air bag module fixing bolt-B
Fixing bolt
: 24.5 N·m (2.5 kg−m, 18 ft−lb)
PHIA0868J
PHIA0888J

SRS-48
SIDE CURTAIN AIR BAG MODULE
Revision: 2007 April2007 M35/M45
INSTALLATION
Install in the reverse order of removal.
CAUTION:

Be careful not to damage the air bag harness.

After the work is completed, make sure no system malfunction is detected by air bag warning
lamp.

In case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis func-
tion and delete the memory by CONSULT-ll.

In case that malfunction is still detected after the avove operation, perform self-diagnosis to repair
malfunctions. Refer to SRS-20, "
SRS Operation Check" .

CRASH ZONE SENSOR
SRS-49
C
D
E
F
G
I
J
K
L
MA
B
SRS
Revision: 2007 April2007 M35/M45
CRASH ZONE SENSORPFP:98531
Removal and InstallationNHS0009G
REMOVAL
CAUTION:

Before servicing, turn ignition switch OFF, disconnect both battery terminal and wait at least 3
minutes.

Do not use air tools or electric tools for servicing.

Do not use old fixing nuts after removal; replace with new nuts.

Do not make an impact to the crash zone sensor by dropping etc. Replace the crash zone sensor if
it has been dropped or sustained an impact.

Replace the crash zone sensor of deployed SRS driver air bag and deployed SRS front passenger
air bag.
1. Remove the crash zone sensor.

Remove the front grille. Refer to EI-16, "Removal and Installation" .

Remove the crash zone sensor fixing nuts.

Disconnect the crash zone sensor harness connector.
INSTALLATION
Install in the reverse order of removal.
CAUTION:

Be careful not to damage the crash zone sensor harness.

After the work is completed, make sure no system malfunction is detected by air bag warning
lamp.

In case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis func-
tion and delete the memory by CONSULT−ll.

In case that malfunction is still detected after the above operation, perform self-diagnosis to repair
malfunctions. Refer to SRS-20, "
SRS Operation Check" . Fixing nut
: 10.8 N·m (1.1 kg−m, 8 ft−lb)
PHIA1116E

SRS-50
SIDE AIR BAG (SATELLITE) SENSOR
Revision: 2007 April2007 M35/M45
SIDE AIR BAG (SATELLITE) SENSORPFP:98830
Removal and InstallationNHS0009H
REMOVAL
CAUTION:

Before servicing, turn ignition switch OFF, disconnect both battery terminal and wait at least 3
minutes.

Do not use air tools or electric tools for servicing.

Do not use old fixing nuts after removal; replace with new nuts.

Do not make an impact to the side air bag (satellite) sensor by dropping etc. Replace the side air
bag (satellite) sensor if it has been dropped or sustained an impact.

Replace the satellite sensor of deployed SRS front side air bag and deployed SRS side curtain air
bag.
1. Remove the side air bag (Satellite) sensor.

Remove front seat belt. Refer to SB-29, "Removal and Installation of Front Seat Belt" .

Remove fixing nuts, then remove side air bag (Satellite) sen-
sor.

Disconnect the side air bag (Satellite) sensor harness con-
nector.
INSTALLATION
Install in the reverse order of removal.
CAUTION:

Be careful not to damage the satellite sensor harness.

After the work is completed, make sure no system malfunction is detected by air bag warning
lamp.

In case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis func-
tion and delete the memory by CONSULT−ll.

In case that malfunction is still detected after the above operation, perform self-diagnosis to repair
malfunctions. Refer to SRS-20, "
SRS Operation Check" . Fixing nut
: 10.8 N·m (1.1 kg−m, 8 ft−lb)
PHIA0902J

SRS-52
DIAGNOSIS SENSOR UNIT
Revision: 2007 April2007 M35/M45
DIAGNOSIS SENSOR UNITPFP:28556
Removal and InstallationNHS0009J
REMOVAL
CAUTION:

Before servicing, turn ignition switch OFF, disconnect both battery terminal and wait at least 3
minutes.

Before disconnecting the air bag sensor unit harness connector, be sure to disconnect the each
harness connector of the air bag module and pre-tensioner seatbelt to prevent air bag deployment
by static electricity and pre-tensioner seatbelt operation.

Do not use air tools or electric tools for servicing.

Do not use old fixing bolts after removal; replace with new bolts.

Do not make an impact to the diagnosis sensor unit by dropping etc. Replace the diagnosis sen-
sor unit if it has been dropped or sustained an impact.

Replace the diagnosis sensor unit of deployed SRS air bag and deployed SRS front seat belt pre-
tensioner.
1. Remove the diagnosis sensor unit.

Disconnect each connector of all air bag modules and pre-tensioner seat belts.

Remove the center console assembly. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .

Disconnect diagnosis sensor unit harness connector.

Remove hex bolts and ground bolt, then remove the diagno-
sis sensor unit.
INSTALLATION
Install in the reverse order of removal.
CAUTION:

Be careful not to damage the diagnosis sensor harness.

After the work is completed, make sure no system malfunction is detected by air bag warning
lamp.

In case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis func-
tion and delete the memory by CONSULT−ll.

In case that malfunction is still detected after the above operation, perform self-diagnosis to repair
malfunctions. Refer to SRS-20, "
SRS Operation Check" .
ECU DISCRIMINATED NO.
After replacing the diagnosis sensor unit, confirm that the diagnosis sensor unit identification is correct for the
vehicle as equipped.Hex bolts
: 24.5 N·m (2.5 kg−m, 18 ft−lb)
Ground bolt A
: 6.9 N·m (0.7kg−m, 61 in−lb)
PHIA0869J
Specification ECU DISCRIMINATED No.
2WD
AW DModels with driver and passenger air bags, seat belt pre-tensioner, side air bags and curtain air
bagsFA D 4 H