2007 INFINITI M35 display

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-43
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
3. CHECK GROUND CIRCUIT FOR ICC SENSOR INTEGRATED UNIT
1. Turn ignition switch OFF.
2. Check continuity between ICC sensor integrated unit harness
connector and ground.
OK or NG
OK >> 1. Replace ICC sensor integrated unit, and adjust laser
beam aiming.
2. Erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
NG >> 1. Repair or replace ICC sensor integrated unit ground harness.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
DTC 3 VHCL SPEED SE CIRCNKS004D2
1. PERFORM ICC SENSOR INTEGRATED UNIT SELF-DIAGNOSIS
1. Perform self-diagnosis.
2. Check if “ABS/TCS/VDC CIRC [C1A04]” (DTC 4) or “CAN COMM CIRCUIT [U1000]” (DTC 100) other
than “VHCL SPEED SE CIRC [C1A03]” (DTC 3) is indicated in self-diagnosis item in the display.
Is any indicated?
YES >> 1. Repair or replace applicable item. Refer to ACS-40, "Diagnostic Trouble Code (DTC) Chart" .
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> GO TO 2.
2. CHECK A/T VEHICLE SPEED SENSOR
With CONSULT-II
With “ICC” “DATA MONITOR”, check if “VHCL SPD AT” operates normally.
OK or NG
OK >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NG >> 1. Perform “A/T” self-diagnosis. Refer to AT- 9 0 , "
CONSULT-II Function (A/T)" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
DTC 4 ABS/TCS/VDC CIRCNKS004D3
1. PERFORM ICC SENSOR INTEGRATED UNIT SELF-DIAGNOSIS
1. Perform self-diagnosis.
2. Check if “CAN COMM CIRCUIT [U1000]” (DTC100) other than “ABS/TCS/VDC CIRC [C1A04]” (DTC 4) is
indicated in self-diagnosis item in the display.
Is it indicated?
YES >> 1. CAN communication inspection. Refer to ACS-61, "DTC 100 CAN COMM CIRCUIT" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
NO >> GO TO 2.
ICC sensor integrated
unit connectorTerminal
GroundContinuity
E61 4 Yes
PKIB8376E

ACS-44
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: 2007 April2007 M35/M45
2. PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT-II
1. Perform “ABS” self-diagnosis. Refer to BRC-23, "
CONSULT-II Functions (ABS)" .
2. Check if malfunction is indicated.
Is malfunction indicated?
YES >> 1. Repair or replace applicable item.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
DTC 5 BRAKE SW/STOP L SWNKS004D4
1. PERFORM ICC SENSOR INTEGRATED UNIT SELF-DIAGNOSIS
1. Perform self-diagnosis.
2. Check if “CAN COMM CIRCUIT [U1000]” (DTC 100) other than “BRAKE SW/STOP L SW [C1A05]” (DTC
5) is indicated in self-diagnosis item in the display.
Is it indicated?
YES >> 1. CAN communication inspection. Refer to ACS-61, "DTC 100 CAN COMM CIRCUIT" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
NO >> GO TO 2.
2. CHECK ICC BRAKE SWITCH WITH ICC DATA MONITOR
With CONSULT-II
With “ICC” “DATA MONITOR”, check if “BRAKE SW” operates normally.
OK or NG
OK >> GO TO 3.
NG >> GO TO 6.
3. CHECK STOP LAMP SWITCH WITH ABS DATA MONITOR
With CONSULT-II
With “ABS” “DATA MONITOR”, check if “STOP LAMP SW” operates normally.
OK or NG
OK >> GO TO 4.
NG >> GO TO 11.
4. PERFORM ECM SELF-DIAGNOSIS
With CONSULT-II
1. Perform “ENGINE” self-diagnosis. Refer to EC-123, "
CONSULT-II Function (ENGINE)" (for VQ35DE) or
EC-826, "
CONSULT-II Function (ENGINE)" (for VK45DE).
2. Check if malfunction is indicated.
Is malfunction indicated?
YES >> 1. Repair or replace applicable item.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> GO TO 5.

ACS-48
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: 2007 April2007 M35/M45
DTC 6 OPERATION SW CIRCNKS004D5
1. PERFORM ICC SENSOR INTEGRATED UNIT SELF-DIAGNOSIS
1. Perform self-diagnosis.
2. Check if “CAN COMM CIRCUIT [U1000]” (DTC 100) other than “OPERATION SW CIRC [C1A06]” (DTC
6) is indicated in self-diagnosis item in the display.
Is it indicated?
YES >> 1. CAN communication inspection. Refer to ACS-61, "DTC 100 CAN COMM CIRCUIT" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
NO >> GO TO 2.
2. CHECK CONNECTOR FOR ECM
1. Turn ignition switch OFF.
2. Disconnect ECM connector, and connect it securely again.
3. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system again.
4. Check if “OPERATION SW CIRC [C1A06]” (DTC 6) is indicated in self-diagnosis item in the display.
Is it indicated?
YES >> GO TO 3.
NO >> Poor connector connection
1. Check connector. (Check connector housing for disconnected, loose, bent, and collapsed ter-
minals. If any malfunction is detected, repair applicable part.)
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
3. CHECK ICC STEERING SWITCH
1. Turn ignition switch OFF.
2. Check ICC steering switch. Refer to ACS-69, "
ICC Steering Switch" .
OK or NG
OK >> GO TO 4.
NG >> 1. Replace ICC steering switch.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-49
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
4. CHECK ICC STEERING SWITCH SIGNAL CIRCUIT
1. Disconnect spiral cable connector and ECM connector.
2. Check continuity between spiral cable harness connector (A)
and ECM harness connector (B).
3. Check continuity between spiral cable harness connector (A)
and ground.
OK or NG
OK >> GO TO 5.
NG >> 1. Repair or replace harness between spiral cable and ECM.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
5. CHECK COMBINATION SWITCH (SPIRAL CABLE)
Check continuity between spiral cable terminals.
OK or NG
OK >> 1. Perform “ENGINE” self-diagnosis. Refer to EC-123,
"CONSULT-II Function (ENGINE)" (for VQ35DE) or
EC-826, "
CONSULT-II Function (ENGINE)" (for
VK45DE).
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
NG >> 1. Replace spiral cable.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
DTC 12 LASER BEAM OFFCNTRNKS004D6
1. ADJUST LASER BEAM AIMING
1. Adjust laser beam aiming. Refer to ACS-15, "
LASER BEAM AIMING ADJUSTMENT"
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system again.
3. Check if “LASER BEAM OFFCNTR [C1A12]” (DTC 12) is indicated in self-diagnosis item in the display.
Is it indicated?
YES >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> INSPECTION END
AB
Continuity
Connector Terminal Connector Terminal
M3931 F108 67
Ye s
34 M71 99
A
GroundContinuity
Connector Terminal
M3931
No
34
PKIB9339E
AB
Continuity
Terminal Terminal
31 18
Ye s
34 21
PKIB9340E

ACS-50
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: 2007 April2007 M35/M45
DTC 13 STOP LAMP RLY FIXNKS004D7
1. PERFORM ICC SENSOR INTEGRATED UNIT SELF-DIAGNOSIS
1. Perform self-diagnosis.
2. Check if “CAN COMM CIRCUIT [U1000]” (DTC 100) other than “STOP LAMP RLY FIX [C1A13]” (DTC 13)
is indicated in self-diagnosis item in the display.
Is it indicated?
YES >> 1. CAN communication inspection. Refer to ACS-61, "DTC 100 CAN COMM CIRCUIT" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
NO >> GO TO 2.
2. CHECK CONNECTOR FOR ECM
1. Turn ignition switch OFF.
2. Disconnect ECM connector, and connect it securely again.
3. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system again.
4. Check if “STOP LAMP RLY FIX [C1A13]” (DTC 13) is indicated in self-diagnosis item in the display.
Is it indicated?
YES >> GO TO 3.
NO >> Poor connector connection
1. Check connector. (Check connector housing for disconnected, loose, bent, and collapsed ter-
minals. If any malfunction is detected, repair applicable part.)
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
3. CHECK STOP LAMP SWITCH WITH ICC DATA MONITOR
With CONSULT-II
With “ICC” “DATA MONITOR”, check if “STOP LAMP SW” operates normally.
OK or NG
OK >> GO TO 11.
NG >> GO TO 4.
4. CHECK STOP LAMP SWITCH INSTALLATION AND ADJUSTMENT
Check stop lamp switch for proper installation, and adjust the switch if necessary. Refer to BR-6, "
BRAKE
PEDAL" .
OK or NG
OK >> GO TO 5.
NG >> 1. Adjust stop lamp switch.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
5. CHECK STOP LAMP SWITCH
Check stop lamp switch. Refer to ACS-69, "
ICC Brake Switch and Stop Lamp Switch" .
OK or NG
OK >> GO TO 6.
NG >> 1. Replace stop lamp switch.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.

ACS-56
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: 2007 April2007 M35/M45
23. CHECK HARNESS BETWEEN STOP LAMP SWITCH AND ABS ACTUATOR AND ELECTRIC UNIT
(CONTROL UNIT)
1. Turn ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) connector.
3. Check continuity between stop lamp switch harness connector
(A) and ABS actuator and electric unit (control unit) harness
connector (B).
4. Check continuity between stop lamp switch harness connector
(A) and ground.
OK or NG
OK >> 1. Perform “ABS” self-diagnosis. Refer to BRC-23, "CONSULT-II Functions (ABS)" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
NG >> 1. Repair or replace harness between stop lamp switch and ABS actuator and electric unit (control
unit).
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
DTC 14 ECM CIRCUITNKS004D8
1. PERFORM ICC SENSOR INTEGRATED UNIT SELF-DIAGNOSIS
1. Perform self-diagnosis.
2. Check if “CAN COMM CIRCUIT [U1000]” (DTC 100) other than “ECM CIRCUIT [C1A14]” (DTC 14) is indi-
cated in self-diagnosis item in the display.
Is it indicated?
YES >> 1. CAN communication inspection. Refer to ACS-61, "DTC 100 CAN COMM CIRCUIT" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
NO >> GO TO 2.
2. PERFORM ECM SELF-DIAGNOSIS
With CONSULT-II
1. Perform “ENGINE” self-diagnosis. Refer to EC-123, "
CONSULT-II Function (ENGINE)" (for VQ35DE) or
EC-826, "
CONSULT-II Function (ENGINE)" (for VK45DE).
2. Check if malfunction is indicated.
Is malfunction indicated?
YES >> 1. Repair or replace applicable item.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
AB
Continuity
Connector Terminal Connector Terminal
E124 4 E30 30 Yes
A
GroundContinuity
Connector Terminal
E124 4 No
PKIC0834E

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-57
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
DTC 15 GEAR POSITIONNKS004D9
1. PERFORM ICC SENSOR INTEGRATED UNIT SELF-DIAGNOSIS
1. Perform self-diagnosis.
2. Check if “VHCL SPEED SE CIRC [C1A03]” (DTC 3), “ABS/TCS/VDC CIRC [C1A04]” (DTC 4) or “CAN
COMM CIRCUIT [U1000]” (DTC100) other than “GEAR POSITION [C1A15]” (DTC 15) is indicated in self-
diagnosis item in the display.
Is any indicated?
YES >> 1. Repair or replace applicable item. Refer to ACS-40, "Diagnostic Trouble Code (DTC) Chart" .
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> GO TO 2.
2. CHECK VEHICLE SPEED SIGNAL
With CONSULT-II
With “ICC” “DATA MONITOR”, check if “VHCL SPEED SE” operates normally.
OK or NG
OK >> GO TO 3.
NG >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
3. CHECK SHIFT GEAR POSITION
Check if gear positions are correct in A/T.
OK or NG
OK >> GO TO 5.
NG >> GO TO 4.
4. CHECK TCM GEAR POSITION SIGNAL
With CONSULT-II
With “A/T” “DATA MONITOR”, check if gear positions are correct.
OK or NG
OK >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NG >> 1. Perform “A/T” self-diagnosis. Refer to AT- 9 0 , "
CONSULT-II Function (A/T)" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
5. CHECK TCM TURBINE REVOLUTION
With CONSULT-II
With TCM diagnosis, check if turbine revolution sensor is normal. Refer to AT- 11 7 , "
DTC P0717 TURBINE
REVOLUTION SENSOR" .
OK or NG
OK >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NG >> 1. Perform “A/T” self-diagnosis. Refer to AT- 9 0 , "
CONSULT-II Function (A/T)" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.

ACS-58
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: 2007 April2007 M35/M45
DTC 16 RADAR STAINNKS004DA
1. VISUAL INSPECTION 1
Check ICC sensor integrated unit body window for contamination and foreign materials.
Is it found?
YES >> 1. If any, remove them.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> GO TO 2.
2. VISUAL INSPECTION 2
Check ICC sensor integrated unit body window for cracks and scratches.
Is it found?
YES >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> GO TO 3.
3. ASKING COMPLAINTS
1. Ask if there is any trace of contamination or foreign material on ICC sensor integrated unit.
2. Ask if vehicle was driven in snow or ICC sensor integrated unit was frosted.
3. Ask if ICC sensor integrated unit was fogged temporarily. (Front window glass may have also tended to be
fogged.)
Is there any symptom?
YES >> Explain difference in displays between contamination detection result and current indication to
customer, and tell them “This is not malfunction”.
NO >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
DTC 18 LASER AIMING INCMPNKS004DB
1. ADJUST LASER BEAM AIMING
1. Adjust laser beam aiming. Refer to ACS-15, "
LASER BEAM AIMING ADJUSTMENT" .
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system again.
3. Check if “LASER AIMING INCMP [C1A18]” (DTC 18) is indicated in self-diagnosis item in the display.
Is it indicated?
YES >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> INSPECTION END
DTC 21 UNIT HIGH TEMPNKS004DC
1. CHECK SYMPTOM
Check if cooling system malfunctions.
Does it malfunction?
YES >> 1. Repair cooling system.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.