2007 INFINITI M35 lock

INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
BL-143
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45
35 LG Vehicle speed signal Input ONAt speedometer operation (vehi-
cle speed approx. 40 km/h)
37 P CAN-LInput/
Output—— —
38 L CAN-HInput/
Output—— —
39 BR/WPush-button ignition
switchInput —Push-button ignition switch is
pressed0
Push-button ignition switch is
releasedBattery voltage
40 B Ground — — — 0
41 Y Power source (fuse) Input — — Battery voltage
42 P PDU wake up signal OutputLOCKSleep condition (30 seconds or
more after all doors are closed
under the condition that the igni-
tion switch position is in the
LOCK position)Battery voltage
—Wake-up condition (Open driver
door)0
43 G Starter signal OutputON At starter motor cranking 0
— Any condition other than above Battery voltage
46 VSteering lock control
signal-1Output—Push-button ignition switch is
pressed under the condition that
Intelligent Key is in the vehicle or
Intelligent Key is insertedBattery voltage
LOCKIgnition switch position is in
LOCK position (Steering lock
activated)Battery voltage → 0 → Battery
voltage
(Battery voltage is detected
when activating the steering
lock)
47 LGInside key antenna (+)
signal
(Instrument center)Input/
Output
LOCK Any door open → closed
(Door switch: ON → OFF)
48 VInside key antenna (–)
signal
(Instrument center)Input/
Output
49 BInside key antenna (+)
signal
(console)Input/
Output
LOCKAny door open → closed
(Door switch: ON → OFF)
50 WInside key antenna (–)
signal
(console)Input/
Output Termi-
nal
No.Wire
colorItemSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Push-
button
ignition
switch
positionOperation or conditions
PKIA1935E
SIIA1910J
SIIA1910J

BL-144
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
Revision: 2007 April2007 M35/M45
51 F/LInside key antenna (+)
signal
(Rear seat)Input/
Output
LOCKAny door open → closed
(Door switch: ON → OFF)
52 R/WInside key antenna (–)
signal
(Rear seat)Input/
Output
53 G/WInside key antenna (+)
signal
(Trunk room)Input/
Output
LOCKAny door open → closed
(Door switch: ON → OFF)
54 LGInside key antenna (–)
signal
(Trunk room)Input/
Output
56 B Ground — — — 0
57 L Power source (fuse) Input — — Battery voltage
58 OA/T device (Detention
switch)Output LOCKAt sleep (30 seconds or more
after all doors are closed under
the condition that the ignition
switch position is in the LOCK
position)0
At wake-up (Open driver door) Battery voltage
63 P Stop lamp switch Input —Brake pedal depressed Battery voltage
Brake pedal released Battery voltage
64 L/RPush-button ignition
switch illuminationOutput —Push-button ignition switch illumi-
nation is turned on2.6
Push-button ignition switch illumi-
nation is turned off
(15 seconds or more after the
driver door is closed)0
69 OSteering lock unit con-
dition signal-1InputLOCK Steering lock: Lock 0
ACC
Steering lock: UnlockBattery voltage
ON Battery voltage
70 L/YSteering lock unit con-
dition signal-2InputLOCK Steering lock: Lock Battery voltage
ACC
Steering lock: Unlock0
ON 0
71 LGSteering lock control
signal-2OutputLOCKPush-button ignition switch is
pressed under the condition that
Intelligent Key is in the vehicle or
Intelligent Key is insertedBattery voltage
ACCIgnition switch position is in
LOCK position (Steering lock
activated)Battery voltage → 0 → Battery
voltage
(Battery voltage is detected
when activating the steering
lock)
72 B Ground — — — 0 Te r m i -
nal
No.Wire
colorItemSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Push-
button
ignition
switch
positionOperation or conditions
SIIA1910J
SIIA1910J

INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
BL-145
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45
Terminals and Reference Value for Steering Lock UnitNIS001YF
Terminals and Reference Value for BCMNIS001YG
Te r m i -
nal
No.Wire
colorItemSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Push-
button
ignition
switch
positionOperation or conditions
1 GR PDU signal Input LOCKPress push-button ignition
switch with Intelligent Key
inside vehicle0 → Battery voltage → 0
(Battery voltage is detected when
pressing the push-button ignition
switch)
3 O Condition signal-1 OutputLOCK Steering lock: Lock 0
ACC
Steering lock: UnlockBattery voltage
ON Battery voltage
4P/BIntelligent Key unit
signalInput/
OutputLOCK Steering lock: Lock Battery voltage
ACC
Steering lock: Unlock0
ON 0
5 B Ground — — — 0
6 B Ground — — — 0
7 LG Power source Input LOCK — Battery voltage
8 L/Y Condition signal-2 OutputLOCK Steering lock: Lock Battery voltage
ACC
Steering lock: Unlock0
ON 0
Te r m i -
nal
No.Wire
colorItemSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Push-but-
ton igni-
tion
switch
positionOperation or conditions
23 W/V Security indicator Output LOCKIntelligent Key is removed from key
slot and power supply position is in
LOCK positionBattery voltage → 0
(Every 2.4 seconds)
37 LGKey slot
(Key switch signal)Input LOCKIntelligent Key is removed from key
slot0
Intelligent Key is inserted into key slot Battery voltage
38 WIgnition power supply
(ON or START)Input ONPower supply position is in ON posi-
tionBattery voltage
39 L CAN-HInput/
Output—— —
40 P CAN-LInput/
Output—— —
42 P Power source (fuse) Input — — Battery voltage
52 B Ground — — — 0
55 WPower source (Fusil-
lade link)Input — — Battery voltage

BL-146
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
Revision: 2007 April2007 M35/M45
Terminals and Reference Value for IPDM E/RNIS001YH
Te r -
minal
No.Wire
ColorItemSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Push-
button
ignition
switch
positionOperation or conditions
4 W/R Starter motor power supply InputLOCK — 0
START Starter motor is activating Battery voltage
49 L CAN HInput/
Output—— —
50 P CAN LInput/
Output—— —
53 GR/R Shift position signal InputONA/T selector lever is in N or P
positionBattery voltage
LOCKA/T selector lever is in any
position other than P and N
position0

INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
BL-147
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45
Terminals and Reference Value for PDUNIS001YI
Te r -
minal
No.Wire
colorItemSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Push-
button
ignition
switch
positionOperation or conditions
1 P Wake up signal InputLOCKSleep condition (30 seconds or more
after all doors are closed under the
condition that the power supply posi-
tion is in the LOCK position)Battery voltage
— Wake-up condition (Open driver door) 0
2 G Starter control signal InputON At starter motor cranking 0
— Any condition other than above Battery voltage
3GRSteering lock unit
power sourceOutputLOCKPush-button ignition switch is pressed
under the condition that Intelligent
Key is in the vehicle or Intelligent Key
is inserted0 → Battery voltage → 0
— Any condition other than above 0
6VSteering lock control
signal-1Input—Push-button ignition switch is pressed
under the condition that Intelligent
Key is in the vehicle or Intelligent Key
is insertedBattery voltage
LOCKPower supply position is in LOCK
position
(Steering lock activated)Battery voltage → 0 → Bat-
tery voltage
(Battery voltage is detected
when activating the steer-
ing lock)
7LGSteering lock control
signal-2Input—Push-button ignition switch is pressed
under the condition that Intelligent
Key is in the vehicle or Intelligent Key
is insertedBattery voltage
LOCKPower supply position is in LOCK
position
(Steering lock activated)Battery voltage → 0 → Bat-
tery voltage
(Battery voltage is detected
when activating the steer-
ing lock)
9OSteering lock feed
back signalOutput— Steering lock: Lock 0
LOCK Steering lock: Unlock 8
10 B Ground — — — 0
11 YIPDM E/R current
signalOutputSTART At starter motor cranking 5
LOCK Any condition other than above 2
12 R Feed back signal OutputLOCKSleep condition (30 seconds or more
after all doors are closed under the
condition that the power supply posi-
tion is in the LOCK position)1
—Wake-up condition (any condition
other than above)0
13 R Starter relay OutputSTART At starter motor cranking Battery voltage
— Any condition other than above 4
14 SB Power source (fuse) Input — — Battery voltage
15 LPower source (fus-
ible link)Input — — Battery voltage
17 GPower source (fus-
ible link)Input — — Battery voltage

BL-148
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
Revision: 2007 April2007 M35/M45
Work FlowNIS001YJ
1. LISTEN TO CUSTOMER COMPLAINT OR REQUEST
Get symptoms or listen to customer complaints or request.
NOTE:
In case of request for Intelligent Key or IVIS (NATS) system repair, the key ID re-registration might be neces-
sary. Keep all the Intelligent Keys before work for the re-registration.
Key ID registration request>>Resister Intelligent Key by referring to Technical Bulletin.
Request for malfunction repair.>>GO TO 2.
2. CHECK DOOR LOCK AND REMOTE KEYLESS ENTRY FUNCTION
Check that Door Lock and remote control function of Intelligent Key operate normally.
Door Lock or remote keyless entry function is malfunctioning.>>Malfunction of Door Lock and remote control
function, Refer to BL-43, "
INTELLIGENT KEY SYSTEM" .
Door Lock and remote keyless entry function are normal.>>GO TO 3.
3. CONFIRMATION BEFORE DIAGNOSIS
Before performing diagnostic procedure, grasp the operating systems with referring to the items below.

“System operation with carrying Intelligent Key”. Refer to BL-127, "OPERATION WHEN INTELLIGENT
KEY IS CARRIED" .

“System operation by using Key slot”. Refer to BL-128, "OPERATION WHEN KEY SLOT IS USED" .
>> GO TO 4.
4. CONFIRM SELF DIAGNOSIS 1
Start CONSULT-II with Push-button ignition switch in lock position and confirm SELF DIAG RESULT “Intelli-
gent Key”. Refer to BL-150, "
CONSULT-II Inspection Procedure" .
No malfunction>>GO TO 5.
Malfunction exist>>Repair the items displayed in “SELF DIAG RESULTS”. Refer to BL-150, "
SELF-DIAG-
NOSTIC RESULTS" .
5. CONFIRM SELF DIAGNOSIS 2
Start CONSULT-II with Push-button ignition switch in lock position and confirm SELF DIAG RESULTS “NATS
BCM or S/ENT” and “NATS I-KEY”. Refer to BL-265, "
CONSULT-II INSPECTION PROCEDURE" .
NOTE:
NATS program card is necessary to display “SELF DIAG RESULTS”.
No malfunction>>GO TO 6.
Malfunction exist>>Repair the items displayed in “SELF DIAG RESULTS”. Refer to BL-268, "
“NATS BCM OR
S/ENT” SELF-DIAGNOSTIC RESULTS ITEM CHART" and BL-269, "“NATS I-KEY” SELF-DIAG-
NOSTIC RESULTS ITEM CHART" .

INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
BL-149
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45
6. CHECK INTELLIGENT KEY FUNCTION
Operate Push-button ignition switch with carrying Intelligent Key to check the power source position can be
turned with all of the Intelligent Keys.
CAUTION:
Operate Push-button ignition switch without depressing the brake pedal.
Can be operated with all of the Intelligent Keys>>GO TO 7.
Can not be operated with particular Intelligent Key>>Check the malfunctioning Intelligent Key. Refer to BL-
124, "INTELLIGENT KEY BATTERY INSPECTION" .
Can not be operated with any of the Intelligent Keys>>Perform Diagnostic Procedure. Refer to BL-177,
"Trouble Diagnosis Symptom Chart 1" .
7. CHECK TURNING TIMING OF POWER SOURCE POSITION 1
Check the power source turning delay time after Push-button ignition switch is pushed. (Approx. 3 sec)
CAUTION:
Operate Push-button ignition switch without depressing the brake pedal.
No delay time exists>>GO TO 8.
Delay time exists>>Perform Diagnostic Procedure. Refer to BL-178, "
Trouble Diagnosis Symptom Chart 2" .
8. CHECK TURNING TIMING OF POWER SOURCE POSITION 2
Check all the Intelligent Keys for power source turning delay time after Push-button ignition switch is pushed
with Intelligent Key inserted into key slot. (Approx. 3 sec)
CAUTION:
Operate Push-button ignition switch without depressing the brake pedal.
No delay time exists>>GO TO 9.
Delay time exists when operated with particular Intelligent Key.>>Perform “C/U INITIALIZATION” referring to
CONSULT-II operation manual IVIS/NVIS NATS. In case that delay time still exists after the initial-
ization, replace the Intelligent Key.
Delay time exists when operated with any of the Intelligent Keys.>>Perform Diagnostic Procedure. Refer to
BL-178, "
Trouble Diagnosis Symptom Chart 3" .
9. CHECK ENGINE START FUNCTION
Check that engine can be started with Intelligent Key carried and inserted into the key slot respectively.
Engine can be started.>>GO TO 10.
Engine cannot be started.>>Inspect Trouble Diagnosis Flow Chart for IVIS (NATS). Refer to BL-272, "
Trou-
ble Diagnoses Flow Chart for IVIS (NATS)" .
10. CHECK SECURITY INDICATOR FUNCTION
Check Security Indicator for lighting up under the two conditions below.

Security Indicator lights off when Push-button ignition switch is pushed with Intelligent Key inserted into or
pulled out of the key slot.

Security Indicator blinks when Intelligent Key is pulled out and Push-button ignition switch is in lock posi-
tion.
Lighting up condition is normal.>>Inspection END.
Lighting up condition is malfunctioning.>>Perform Security Indicator Inspection. Refer to BL-274, "
Check
Security Indicator Harness" .

BL-150
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
Revision: 2007 April2007 M35/M45
CONSULT-II Functions (INTELLIGENT KEY)NIS001YK
CONSULT-II can display each diagnostic item using the diagnostic test modes as shown below.
CONSULT-II Inspection ProcedureNIS001YL
CAUTION:
If CONSULT-II is used with no connection CONSULT-II CONVERTER, malfunctions might be detected
in self-diagnosis depending on control unit which performs CAN Communication.
BASIC OPERATION
Refer to GI-38, "CONSULT-II Start Procedure" .
CONSULT-II Application ItemsNIS001YM
SELF-DIAGNOSTIC RESULTS
How to Read SELF-DIAGNOSTIC RESULTS
Part to be diagnosed Test item, Diagnosis mode Description
Intelligent KeyWORK SUPPORT Changes settings for each function.
SELF-DIAG RESULTS Intelligent Key unit performs CAN communication diagnosis.
DATA MONITOR Displays Intelligent Key unit input data in real time.
CAN DIAGNOSTIC SUPPORT
MONITORThe results of transmit/receive diagnosis of CAN Communication can
be read.
ACTIVE TESTOperation of electrical loads can be checked by sending driving signal
to then.
ECU PART NUMBER Displays Intelligent Key unit part No.
PIIB6280E
Suspect Systems
[DTC]Diagnostic item is detected when... Repair work Reference page
CAN COMM CIRCUIT
[U1000]Malfunction is detected in CAN communicationPerform CAN communi-
cation system inspectionBL-179
CONTROL UNIT (CAN)
[U1010]Malfunction is detected in CAN communication caused
by Intelligent Key unit internal malfunctionReplace Intelligent Key
unit.BL-179
STRG COMM 1
[B2013]Communication malfunction with steering lock unit is
detectedCheck steering lock unitBL-155
STEERING LOCK UNIT
[B2551]Even if the communication with steering lock unit is
normally performed, the steering lock is malfunctioningReplace steering lock
unitBL-157
INTELLIGENT KEY
[B2552]Internal malfunction is detected in Intelligent Key unitReplace Intelligent Key
unit.BL-161