2007 INFINITI M35 instrument panel

BLOWER UNIT
ATC-129
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2007 April2007 M35/M45
BLOWER UNITPFP:27200
Removal and InstallationNJS000IA
REMOVAL
1. Remove instrument passenger lower cover and glove box cover. Refer to IP-10, "INSTRUMENT PANEL
ASSEMBLY" .
2. Remove BCM. Refer to BCS-15, "
Removal and Installation of BCM" .
3. Remove mounting nuts, and then remove ECM with bracket
attached.
4. Disconnect intake door motor connector and blower fan motor
connector.
5. Remove mounting bolt and screw from blower unit.
CAUTION:
Move blower unit rightward, and remove locating pin (1
part) and joint. Then remove blower unit downward.
6. Remove blower unit.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
Make sure locating pin (1 part) and joint are securely inserted.
R J I A 4 111 E
RJIA4112E

BLOWER MOTOR
ATC-131
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2007 April2007 M35/M45
BLOWER MOTORPFP:27226
Removal and InstallationNJS000HC
REMOVAL
1. Remove instrument passenger lower cover. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Disconnect blower motor connector.
3. Remove mounting screws, and then remove blower motor.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA4114E

IN-CABIN MICROFILTER
ATC-133
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2007 April2007 M35/M45
IN-CABIN MICROFILTERPFP:27277
Removal and InstallationNJS000I9
FUNCTION
Air inside passenger compartment is kept clean at either recircula-
tion or fresh mode by installing in-cabin microfilter into blower unit.
REPLACEMENT TIMING
Replace in-cabin microfilter.
Refer to MA-9, "
CHASSIS AND BODY MAINTENANCE" in Schedule 1 and MA-10, "CHASSIS AND BODY
MAINTENANCE" in Schedule 2.
When replacing filter, affix a caution label inside the glove box.
REPLACEMENT PROCEDURES
1. Remove glove box. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove filter cover, and then remove in-cabin microfilter.
3. Take out in-cabin microfilter from blower unit.
4. Replace with new one and reinstall on blower unit.
5. Reinstall glove box.
RJIA1331E
RJIA4116E

ATC-134
HEATER & COOLING UNIT ASSEMBLY
Revision: 2007 April2007 M35/M45
HEATER & COOLING UNIT ASSEMBLYPFP:27110
Removal and InstallationNJS000HF
REMOVAL
1. Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2. Drain coolant from cooling system. Refer to CO-11, "
Changing Engine Coolant" (VQ35DE) or CO-40,
"Changing Engine Coolant" (VK45DE).
3. Remove cowl top cover. Refer to EI-18, "
COWL TOP" .
4. Disconnect low-pressure flexible hose and high-pressure pipe 1
from evaporator.
a. Set a disconnector [high-pressure side (SST: 9253089908), low-
pressure side (SST: 9253089916)] on A/C piping.
b. Slide a disconnector toward vehicle front until it clicks.
c. Slide A/C piping toward vehicle front and disconnect it.
CAUTION:
Cap or wrap the joint of low-pressure flexible hose, low-
pressure pipe 1 and high-pressure pipe 1, 2 with suitable
material such as vinyl tape to avoid the entry of air.
5. Remove electric throttle control actuator. Refer to EM-21,
"INTAKE MANIFOLD COLLECTOR" (VQ35DE) or EM-179, "INTAKE MANIFOLD" (VK45DE).
6. Disconnect two heater hoses from heater core.
7. Remove instrument panel & pad. Refer to IP-10, "
INSTRUMENT PANEL ASSEMBLY" .
8. Remove blower unit. Refer to ATC-129, "
BLOWER UNIT" .
9. Remove clips of vehicle harness from steering member.
10. Remove mounting nuts and bolts, and then remove instrument stays.
RJIA4117E
RJIA4118E
RJIA4119E

DUCTS AND GRILLES
ATC-143
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2007 April2007 M35/M45
DUCTS AND GRILLESPFP:27860
Removal and InstallationNJS000HL
COMPONENT LAYOUT
Grilles, Ducts and Nozzles
1. Side defroster nozzle (right) 2. Front defroster nozzle 3. Side defroster nozzle (left)
4. Side defroster duct (left) 5. Side defroster grille (left) 6. Side ventilator grille (left)
7. Upper ventilator grille 8. Center ventilator grille 9. Side ventilator grille (right)
10. Instrument panel & pad 11. Front defroster grille (right) 12. Side defroster grille (right)
13. Side defroster duct (right) 14. Ventilator duct 15. Front defroster grille (left)
16. Upper ventilator duct
SJIA1787E

DUCTS AND GRILLES
ATC-145
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2007 April2007 M35/M45
REMOVAL
Removal of Center Ventilator Grilles
Remove center ventilator assembly. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
Removal of Side Ventilator Grilles
Remove side ventilator assembly. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
Removal of Upper Ventilator Grille
Remove mounting metal clips, and then remove upper ventilator
grille.
Removal of Upper Ventilator Duct
1. Remove instrument panel & pad. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove mounting screws, and then remove upper ventilator
duct, using power tools.
RJIA4134E
RJIA4135E

ATC-146
DUCTS AND GRILLES
Revision: 2007 April2007 M35/M45
Removal of Front Defroster Nozzle, Side Defroster Nozzles and Ventilator Duct
1. Remove instrument panel & pad. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove mounting clips, and then remove side defroster nozzles.
3. Remove front defroster nozzle.
4. Remove mounting screws, and then remove ventilator duct, using power tools.
Removal of Side Defroster Grilles
Remove side defroster grilles, using clip remover.
Removal of Side Defroster Ducts
1. Remove front pillar garnish. Refer to EI-38, "FRONT PILLAR GARNISH" .
2. Remove mounting screws, and then remove side defroster
ducts.
RJIA4136E
RJIA4137E
RJIA4138E

DUCTS AND GRILLES
ATC-147
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2007 April2007 M35/M45
Removal of Rear Ventilator Grille
1. Remove console rear finisher. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove mounting clips, and then remove rear ventilator grille.
Removal of Rear Ventilator Ducts
1. Remove center console. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove mounting clip, and then remove rear ventilator duct 2.
3. Remove mounting clips, and then remove rear ventilator ducts
1.
4. Remove mounting screws, and then remove rear ventilator duct
3.
RJIA4139E
RJIA4140E
RJIA4141E
RJIA4142E