2007 FORD FIESTA wheel bolts

303-01 B-93 Engine - 2.OL Duratec-HE (M14) 303-01 B-93
DISASSEMBLY
Discard the gasket. 59. Using
the special tool, lock the flywheel in
position.
56. Remove the crankcase vent oil separator.
60. Remove the flywheel.
Discard the bolts.
57.
Remove the oil filter adapter.
Discard the gasket.
61.
Remove the special tool.
62. Remove the oil pan.
58. Remove the clutch disc and pressure plate.
For additional information, refer to: Clutch
Disc and Pressure 'late (308-01 Clutch, 63. Remove the crankshaft rear seal carrier.
Removal and Installation).
2006.0 Fiesta 1212006 G451309en
procarmanuals.com

303-01 B-96 Engine - 2.OL Duratec-HE (M14) 303-01 B-96
ASSEMBLY
Tighten the bolts in the sequence shown. 7. N0TE:lnstall new flywheel bolts.
Install the flywheel.
Clean the mating faces of the cylinder block
I
and the oil pan with a suitable metal surface
cleaner.
8. Using the special tool, lock the flywheel in
position.
N0TE:lnstall the oil pan within 10 minutes
of applying the sealant and tighten the
retaining bolts within a further
5 minutes.
Apply a
3 mm bead of sealant to the oil pan.
9. Tighten the flywheel bolts.
Tighten the bolts in the sequence shown in
three stages.
5. Using a suitable straight edge, align the oil Stage 1: 50 Nm.
pan to the cylinder block mating face on the Stage 2: 80 Nm.
timing chain side. Stage 3: 11 2 Nm. I I
6. Tighten the oil pan retaining bolts.
Tighten the bolts in the sequence shown.
l I. -.
10. Remove the special tool.
2006.0 Fiesta 1212006 G451310en
procarmanuals.com

Automatic TransmissionlTransaxle -
Vehicles With: 4-Speed Automatic
Transmission
(AW81-40)
SPECIFICATIONS
Lubricants, Fluids, Sealers and Adhesives
A WARN1NG:Refer to the Material Safety
Data Sheets for the Automatic Transmis-
sion Fluid E-AW. Failure to follow this
instruction may result in personal injury.
Certain Transmission and Power Steering
fluids supplied to Ford contain additives
which may cause skin irritation or other
skin reactions after contact.
Automatic transmission fluid
Grease
Capacities
Specif icat
ions
WSS-M2C 924-A
WSD-MI C
230-A
For additional information, refer to: Health
and Safety Precautions
(1 00-00 General
Information, Description and Operation).
See
- Transmission Fluids. Automatic transmission fluid
(including cooler and tubes)
I Transaxle to engine flange retaining bolts I 47 I 35 I - I
Litres
5.75
Torque Specifications
I Engine ground cable to transaxle retaining nut I 25 I 18 I - I
I Torque converter retaining nuts I 27 I 20 I - I
lb-in Item
I Starter motor retaining bolts I 47 I 35 I - I
,I Engine and transaxle rear mount retaining bolt I 80 I 59 I - I
Nm
I Lower arm to the wheel knuckle I 48 I 35 I - I
I b-ft
I tie-rod end to the wheel knuckle I 48 I 35 I - I
I Exhaust flexible pipe to catalytic converter I 44 I 32 I - I
I Engine support insulator bolts I 48 I 35 I - I
IGnition switch to starter motor solenoid cable I 7 I - I 62 I
I Battery to starter motor solenoid cable I 12 I 9 I - I
-I indicator tube to transaxle retaining bolt I 25 I 18 I - I
I Selector lever cable bracket retaining bolts I 20 I 15 I - I - -
I Ground cable to transaxle retaining bolt
I Engine rear mount outer retaining nuts
I Engine rear mount center retaining nut I 90 I 66 I - I
I Battery tray retaining bolts I 25 I 18 I - I
I Strut and spring assembly top mount nuts I 25 I 18 I - I - -
Transaxle drain plug
Vehicle speed sensor (VSS) heat shield retaining
1 nut
Turbine
shaft speed (TSS) sensor retaining bolt
Vehicle speed sensor (VSS) retaining stud bolt
2006.0 Fiesta 1212006 G371496en
17
5
13 13 -
-
10
44
-
procarmanuals.com

Manual Transmission/Transaxle and Clutch -
308-00-3 General Information 308-00-3
DIAGNOSIS AND TESTING
Manual Transaxle and Clutch
lnspection and Verification
General Equipment selected with the engine running and the parking
brake applied, without any concerns, the clutch
2. If the gear@) cannot be selected, REFER to
Symptom Chart.
Ultraviolet
fluid leak detection equipment
1. Verify the customer concern.
Transaxle noise concerns
2. Visually inspect for obvious signs of mechanical is
OK.
damage. 1. Check the engine and transaxle support for
Oil leaks.
Visibly damaged or worn components.
Visual lnspection Chart insufficient gap between the transaxle and the
body.
REFER to:
RoadlRoller Testing (1 00-00 General
Information, Description and Operation).
Mechanical 2. Road test the vehicle.
4. If the cause is not evident, verify the symptom
and REFER to Symptom Chart.
Oil leakage concerns
Loose or missing nuts or bolts.
( I The following checks should be carried out before
repairing or installing a new transaxle. 1.
Check the transaxle fluid level. If necessary,
3. If a noise occurs in various gears at the same
- - drain off any excess fluid.
The inspection and verification of manual transaxle
concerns can be considered in three main areas. 2. Clean the transaxle and the adjacent areas
carefully and road test the vehicle.
engine speed,
check if the noise also occurs in
3. If an obvious cause for an observed or reported the neutral position.
If it does, the noise is not
concern is found, correct the cause (if possible) caused
by the transaxle.
before proceeding to the next step. 4.
REFER to Symptom Chart.
Gear shifting concerns REFER to: RoadlRoller Testing (1 00-00 General
Information, Description and Operation).
1, Check the operation of the clutch: Lay a block 3. U~ing suitable ultraviolet fluid leak detection
of wood approximately
25 mm thick under the equipment, locate
the leak and check whether
clutch pedal and depress the clutch pedal as the leaking fluid
is transaxle fluid, brake fluid
far as the stop. If first or second gear can be (from the hydraulically operated clutch)
or
engine oil.
4. REFER to Symptom Chart.
Symptom Chart
Symptom Possible Sources Action
I
Clutch slippage Clutch master
cylinder.
Clutch slave cylinder.
Clutch pressure plate.
Clutch disc.
Engine or transaxle housing oil
or fluid
leak@).
GO to Pinpoint Test A.
Clutch chatter or shudder Engine and transaxle
mounts. REFER to:
Noise, Vibration and
Harshness (NVH) (1 00-04,
Diagnosis and Testing).
Clutch pressure plate.
Clutch disc.
Flywheel.
--
GO to Pinpoint Test B.
- -
2006.0 Fiesta 1212006 G25629en
procarmanuals.com

308-0314 Manual Transmission/Transaxle 308-03-4 -- --
SPECIFICATIONS
2006.0 Fiesta 1212006 GII 3289en
Item
Transaxle housing final drive cover retaining bolts
Transaxle to engine retaining bolts
Engine support insulator to engine retaining bolt
Engine support insulator to
subframe retaining bolts
Engine rear mount outer retaining nuts
Exhaust flexible pipe retaining nuts
Wiring harness retaining bracket retaining nut Power steering high-pressure line retaining bracket
retaining bolt
Lower arm ball joint to the wheel knuckle retaining
nut
Engine rear mount center retaining nut
Intermediate shaft center bearing retaining nuts
Strut and spring assembly top mount retaining nuts
Transmission fluid filler plug
Starter motor retaining bolts
Starter motor wiring harness retaining bracket retaining nuts Nm
12
47
48
48
48
44
22
25
52
90
25
48 35
35
20
Ib-ft
9
35
35
35
35
32
16
21
38
66
18
35
26
26
15
I b-in
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
procarmanuals.com

308-03-24 Manual Transmission/Transaxle 308-03-24
REMOVAL
5. Install the special tools. 9. Disconnect the reversing lamp switch
electrical connector.
//
I I
6. Remove the transaxle upper retaining bolts.
Detach the engine wiring harness bracket Vehicles with automated gearshift
from the transaxle. 10. Remove the gearshift actuator cover.
7. Remove the front wheels and tires. 11. Disconnect the gearshift actuator electrical
For additional information, refer to: Wheel connector (colored
black).
and Tire
(204-04 Wheels and Tires, Removal
and Installation).
8. Remove the starter motor.
Detach the starter motor electrical connector
from the starter motor.
2006.0 Fiesta 1212006 - Gl13290en
procarmanuals.com

308-03-31 Manual TransmissionlTransaxle 308-03-31
REMOVAL
5. Remove the transaxle upper retaining bolts. Detach the wiring harness from the retaining
bracket.
6. Detach the power steering high-pressure line
retaining bracket from the transaxle. 10.
Disconnect the reversing lamp switch
electrical connector.
7. Remove the front wheels and tires.
11. Remove the gearshift cables cover.
For additional information, refer to: Wheel
and Tire (204-04 Wheels and Tires, Removal
I
and Installation).
8. Remove the wiring harness retaining bracket.
9. Remove the starter motor. 12.
Detach the gearshift cables from the
transaxle.
1. Detach the gearshift cables and the selector
cable from the selector levers.
- -
2006.0 Fiesta 1212006 G453416en
procarmanuals.com

308-03-73 Manual Transmission/Transaxle 308-03-73
INSTALLATION
27. Attach the power steering high-pressure 30. Tighten the engine rear mount outer
/ line retaining bracket to the transaxle. retaining nuts. I
28. Install the transaxle upper retaining bolts. 31. Tighten the engine rear mount center
retaining nut.
29. Install the engine wiring harness bracket.
32. Install the battery tray support bracket.
33. Install the front wheels and tires.
For additional information, refer to: Wheel
and Tire
(204-04 Wheels and Tires,
Removal and Installation).
- -- -- --
2006.0 Fiesta 1212006 G453417en
procarmanuals.com