2007 FORD FIESTA jacking

21 1 -00-25 Steering System - General Information 21 1-00-25
GENERAL PROCEDURES
3. Connect the air cleaner outlet pipe. 20. Lower the vehicle.
21. Fill and bleed the power steering system.
For additional information, refer to: (211 -00
Steering System
- General Information)
Power Steering System Filling (General
Procedures),
Power Steering System Bleeding (General
Procedures).
17. Raise and support the vehicle. For
additional information, refer to: (1 00-02
Jacking and Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
18.
N0TE:Make sure that the collar on the hose
is inserted fully into the quick release
coupling.
Remove the blanking cap and connect the
power steering fluid reservoir return hose
( ' quick release coupling.
19. Connect the CKP sensor electrical
connector.
2006.0 Fiesta 1212006 G91886en
procarmanuals.com

211 -00-27 Steering System - General Information 21 1 -00-27
GENERAL PROCEDURES
6. Raise the vehicle until the road wheels are
clear of the floor. Support the vehicle. For
/ j additional information, refer to: (1 00-02
Jacking and Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
7.
N0TE:When filling the power steering fluid
reservoir, make sure that the steering fluid
is clean and not agitated prior to use. The
steering fluid must be poured slowly into the
power steering fluid reservoir to minimize
the possibility of aeration. The steering fluid
level must be checked with the steering fluid
cold.
Fill the power steering fluid reservoir to the
MAX mark with the appropriate steering fluid.
For additional information, refer to:
Specifications (21 1-00 Steering System
-
General Information, Specifications).
8. CAUTIONS:
ADO not continuously crank the engine for
more than 30 seconds.
A~hen flushing the power steering system,
( make sure that the steering fluid in the power
steering fluid reservoir does not fall below
the MIN mark.
N0TE:When filling the power steering fluid
reservoir, make sure that the steering fluid is clean
and not agitated prior to use. The steering fluid
must be poured slowly into the power steering fluid
reservoir to minimize the possibility of aeration.
While cranking the engine turn the steering
wheel from lock to lock.
With the aid of another technician, add a
further
1 liter of clean steering fluid to the
power steering fluid reservoir.
11. When the clean steering fluid has been
added to the power steering fluid reservoir,
turn the ignition switch to the OFF position.
12. Lower the vehicle.
13. Using the special tool, connect the steering
gear to power steering fluid reservoir return
line to the power steering fluid reservoir.
N0TE:When filling the power steering fluid
reservoir, make sure that the steering fluid is clean
and not agitated prior to use. The
steering fluid
must be poured slowly into the power steering fluid 14. Using the special tool, install the spark reservoir to minimize the possibility of aeration. plugs.
While cranking the engine turn the steering
wheel from lock to lock.
With the aid of another technician, add 1 liter
of clean steering fluid to the power steering
fluid reservoir.
9. Wait 60 seconds to allow the starter motor
to cool.
10. CAUTIONS:
ADO not continuously crank the engine
for more than 30 seconds.
Awhen flushing the power steering system,
make sure that the steering fluid in the power
- steering fluid reservoir does not fall below
I, the MIN mark.
- -- - -
2006.0 Fiesta 1212006 G458163en
procarmanuals.com

21 1 -02-1 4 Power Steering 21 1 -02-1 4
REMOVAL AND INSTALLATION
Power Steering Pump to Steering Gear Pressure Line - 1.25L
Duratec-1 6V (Sigma), Vehicles With: Air
Conditioning(13 440 0)
Special Tool(s)
211-188 (13-015)
Detach the power steering line bracket from
the power steering pump mounting bracket.
622
I I 1 3. N0TE:Note the position of the power steering
Socket, Hydraulic Line Union
!:!-269 (I 3-027)
I I line to aid installation.
Removal
All vehicles
1. Detach the coolant expansion tank from the
wheelhouse assembly and position
it to one
side.
I. Remove the retaining bolt.
2. Release the retaining clip.
Detach the power steering line brackets from
the cylinder head.
4. Raise and support the vehicle.
For additional information, refer to: Jacking
(1 00-02 Jacking and Lifting, Description
and Operation)
I Lifting (1 00-02 Jacking and Lifting,
Description and Operation).
2. N0TE:Note the position of the power steering 5m &AUTION:Do not disconnect the power
line to aid installation.
steering pump pressure adapter from the
power steering pump. f ', .
Using the special tool, disconnect the power
steering line from the power steering pump
pressure adapter.
2006.0 Fiesta 1212006 ' G91965en
procarmanuals.com

21 I -02-1 7 Power Steering 211 -02-1 7
REMOVAL AND INSTALLATION
Power Steering Pump to Steering Gear Pressure Line - 1.25L
' . I Duratec-1 6V (Sigma)/l.4L Duratec-1 6V (Sigma)/l .6L
Duratec-1
6V (Sigma), Vehicles Without: Air
Conditioning(l3 440 0)
Special Tool(s)
Expander, Teflon Seal
211-188 (13-015)
( :Removal
Vehicles with manual transaxle
622
Detach the power steering line brackets from
the transaxle.
Socket, Hydraulic Line Union
!:!-269 (I 3-027)
All vehicles
3. Raise and support the vehicle.
For additional information, refer to: Jacking
(100-02 Jacking and Lifting, Description
and Operation)
I. N0TE:Note the position of the power steering I Lifting (100-02 Jacking and Lifting,
line to aid installation. Description
and Operation).
Detach the power steering line bracket from
4m ACAUTION:D~ not disconnect the power
the transaxle. steering
pump pressure adapter from the
power steering pump.
Vehicles with automatic transaxle
2. N0TE:Note the position of the power steering
line to aid installation. Using
the special tool, disconnect the power
steering line from the power steering pump
pressure adapter.
Allow the fluid to drain into a suitable
container.
Discard the O-ring seal.
-- -- -
2006.0 Fiesta 1212006 G397028en
procarmanuals.com

21 1 -02123 Power Steering 21 I -02-23
REMOVAL AND INSTALLATION
11. Fill and bleed the power steering system. Procedures),
For additional information, refer to: (211 -00 Power Steering System
Bleeding (General
Steering System - General Information) Procedures).
Power Steering System Filling (General
Removal Details
ltem 1 Power steering pump pulley
1. Using the special tool, remove the power
steering pump pulley.
I ' 2. CAUTIONS: /,
Acap the power steering pump outlet port
to prevent fluid loss or dirt ingress.
hap the power steering pump to steering
gear pressure line to prevent fluid loss or
dirt ingress.
Item 4 Power steering pump to steering gear
pressure line bracket to intake manifold retaining
bolt
1. Raise and support the vehicle. For additional
information, refer to: (1 00-02 Jacking and
Lifting)
Jacking (Description and Operation),
Jacking (Description and Operation).
2. Detach the power steering pump to steering
gear pressure line from the intake manifold.
Disconnect the power steering pump to
Item 5 Power steering pump to steering gear
steering gear pressure line from the power
pressure line steering pump. 1. Remove the front wheels and tires. Remove and discard the power steering
pump to steering gear pressure line union
For additional information, refer to: Wheel
O-ring seal. and Tire (204-04 Wheels and Tires, Removal
and Installation).
2006.0 Fiesta 1212006 G458165en
procarmanuals.com

21 1 -02-32 Power Steering 21 1-02-32
REMOVAL AND INSTALLATION
7. Fill and bleed the power steering system. For Procedures),
additional information, refer to: (211-00 Power Steering System Bleeding (General
Steering System
- General Information) Procedures). ( ;)
Power Steering System Filling (General
Removal Details
Item 1 Steering gear to power steering fluid
reservoir return line upper retaining clip
1. CAUTIONS:
&ap the steering gear to power steering
fluid reservoir return line to prevent fluid loss
or dirt ingress.
hap the power steering fluid reservoir to
prevent fluid loss or dirt ingress.
Using the special tool, disconnect the
steering gear to power steering fluid
reservoir return line from the power steering
fluid reservoir.
Allow the power steering fluid to drain into a
container.
Item 2 Steering gear to power steering fluid
reservoir return line support bracket to generator
retaining nut
I. N0TE:Note the position of the steering gear
to power steering fluid reservoir return line
support bracket to aid installation.
Detach the generator wiring harness from
the steering gear to power steering fluid
reservoir return line support bracket.
Item 3 Steering gear heat shield
I. Raise and support the vehicle. For additional
information, refer to: (1 00-02 Jacking and
Lifting)
Jacking (Description and Operation),
2. Detach the steering gear to power steering Lifting
(Description and Operation).
fluid reservoir return line from the generator 2.
Detach the steering gear heat shield from
-
wiring harness shield. the
steering gear.
2006.0 Fiesta 1212006 G458167en
procarmanuals.com

21 1-02-48 Power Steering 21 1-02-48
REMOVAL AND INSTALLATION
Power Steering Fluid Cooler(l3 444 0)
Removal 2. Lower the power steering fluid cooler. '-..
I. Raise and support the vehicle. For additional
information, refer to:
(100-02 Jacking and
Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
2. Disconnect the power steering fluid cooler
quick release couplings.
1. Press the power steering fluid cooler hose
quick release coupling locking tangs.
2. Disconnect the power steering fluid cooler
hose quick release coupling.
Allow the fluid to drain into a suitable
container.
3. Remove the radiator splash shield.
4. Lower the vehicle.
5. Remove the power steering fluid cooler.
I. Remove the retaining bolt.
Installation
1. N0TE:Make sure that the collar on the hose
is inserted fully into the quick release
coupling.
To install, reverse the removal procedure.
2. Fill and bleed the power steering system. For
additional information, refer to: (211 -00
Steering System
- General Information)
Power Steering System Filling (General
Procedures),
Power Steering System Bleeding (General
Procedures).
2006.0 Fiesta 1212006 G91972en
procarmanuals.com

303-00-1 7 Engine System - General Information 303-00-1 7
DIAGNOSIS AND TESTING
14. N0TE:Check the EGR tube O-ring seal.
Install a new seal
if necessary. I
, Install the EGR tube to the intake manifold
assembly.
18 Connect the fuel injector wiring harness main
connector.
19 Install the air cleaner.
REFER to: Air Cleaner
- 1.4L Duratorq-TDCi
15 Attach the EGR tube to the cylinder block and (DV) Diesel (303-12 Intake Air Distribution
and
to the EGR valve (if equipped). Filtering, Removal
and Installation).
Using worldwide diagnostic system (WDS), clear
the fault codes from the PCM.
Measure the compression pressure
Engine
- 1.6L Duratorq-TDCi (DV)
biesel)
WARNINGS:
A Do not smoke or carry lighted tobacco or
open flame of any type when working on
or near any fuel related components.
Highly flammable mixtures are always
16 Attach the EGR tube to the EGR cooler (if present and can ignite. Failure to follow
equipped). these instructions may result in personal
injury.
Do not carry out any repairs to the fuel
injection system without checking that the
fuel pressure has dropped to zero and that
the fuel temperature has either reached
ambient temperature or is below
30' C,
whichever is the greater. Failure to follow
these instructions may result in personal
injury.
I. Using datalogger in world wide diagnostic
system (WDS), check that the fuel pressure has
dropped to zero and that the fuel temperature
17. Connect the glow plug relay electrical connector. has
either reached ambient temperature or is
below 30°C, whichever is the greater.
2. Raise and support the vehicle. REFER to:
(1 00-02 Jacking and Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
2006.0 Fiesta 1212006 GI 52554en
procarmanuals.com