2007 FORD FIESTA battery

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01A-123 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-01 A-I 23
INSTALLATION
5. Install the starter motor and the transaxle Install the engine rear mount.
left-hand retaining bolt.
/'
10. lnstall the battery tray support bracket.
6. Raise and support the vehicle.
For additional information, refer to: Lifting
(1 00-02 Jacking and Lifting, Description
and Operation).
7. Position the engine and transaxle assembly
in the engine compartment.
Carefully lower the vehicle.
8.
N0TE:lnstall new engine front mount
, retaining nuts. ' I ' N0TE:Do not tighten the engine front mount
retaining bolts and nuts at this stage.
Install the engine front mount. 11. Install the engine rear support insulator.
9.
N0TE:lnstall new engine rear mount 12. CAUTIONS:
retaining nuts.
Asupport the halfshaft. The inner joint N0TE:Do not tighten the engine rear mount center must not be bent more than 18 degrees. retaining nut at this stage. The outer joint must not be bent more than
45 degrees.
ADO not damage the halfshaft oil seal.
N0TE:lnstall a new center bearing cap and
locknuts.
2006.0 Fiesta 1212006 GII 31 64en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
303-01 A-1 38
INSTALLATION
21. Connect the power steering line to the 25. Connect the ignition switch to starter motor
steering pump.
solenoid and battery to starter motor
solenoid cables.
22. Attach the power steering line support
bracket to the engine block.
26. Connect the crankshaft position (CKP)
sensor electrical connector.
23. N0TE:lnstall new exhaust flange nuts and
a new exhaust flange gasket.
27. Connect the oil pressure switch electrical
Attach the exhaust flexible pipe to the connector.
catalytic converter.
24. Remove the exhaust flexible pipe support.
2006.0 Fiesta 1212006 G380459en
procarmanuals.com

303-01 B-5 Engine - 2.OL Duratec-HE (M14) 303-01 B-5
SPECIFICATIONS
Torque Specifications - --- -- - -- -
Description Nm l b-ft Ib-in
Air cleaner retaining bracket
Air cleaner resonator support bracket retaining bolts Battery cable to generator electrical connector
I Cylinder head retaining bolts I a) I - I - I
Battery tray support bracket retaining bolts
I
--
I Camshaft bearing caps retaining bolts a) IT
15
15
I Camshaft sprocket retaining bolts I 72 I 53 I - I
25
I Camshaft position (CMP) sensor retaining bolt I 6 1 - I 53 I
11
I1
-
-
18
I Engine front cover lower blanking plug I 12 I 9 I - I
-
Engine front cover retaining bolts
Engine front cover upper blanking plug
I Engine support insulator retaining bolts I 48 I 35 I - I
Engine wiring harness bracket to valve cover
retaining nut
a)
10
I Generator upper retaining bolt I 25 I 18 I - I
-
-
I Coolant plugs (4) to cylinder head I 75 I 55 I - I
-
89
Hood latch lever retaining bolts
Crankshaft pulley retaining bolts
Coolant expansion tank retaining nut
Coolant plug to cylinder block
I Power steering pump retaining bolt I 23 I 17 I - I
15
a)
8
43
I
--
I Power steering bracket retaining nut 15 IT
Power steering reservoir retaining bolts
Power steering pipe to the power steering
Power steering supply line to intake manifold
retaining bolt
11
-
-
32
Power steering high-pressure line retaining bracket
retaining bolt
-
-
71
-
9
65
I Power steering return line support bracket retaining I 15 I 11 I - I
1 nut
-
48 80 -
Exhaust
manifold bracket retaining bolts
2006.0 Fiesta 1212006 G451278en
Exhaust manifold upper heat shield retaining bolts
Exhaust manifold lower heat shield retaining bolts
Exhaust manifold to the cylinder head retaining nuts
Exhaust manifold studs to cylinder head
25
10
10
55
17 18
-
-
-
41
13 89
89 -
-
procarmanuals.com

303-01 B-I 6 Engine - 2.OL Duratec-HE (M14) 303-01 B-I 6
GENERAL PROCEDURES
Valve Clearance Adjustment
Feeler gauges 1
Materials
Special
Tool(s) 4.
Unclip the engine wiring harness from the i..
I I
Name Specification
intake manifold.
4. Remove the positive crankshaft ventilation
(PCV) hose.
/ ES21202
&
21211
1. Disconnect the battery ground cable.
General
Equipment
i
Socket, Spark Plug
303-499 (2
1 -202)
Pliers, Valve Stem Seal
303-508
(2 1 -2 1 1 )
- --
For additional information, refer to: Battery
Disconnect (41 4-01 Battery, Mounting and
Cables, General Procedures).
Silicone Sealant
2. Remove the air cleaner.
WSE-M4G323-A4
For additional information, refer to: Air 5. Disconnect the camshaft position (CMP)
Cleaner - 2.OL Duratec-HE (M14) (303-1 2
sensor electrical connector.
Intake Air Distribution and Filtering,
Removal and Installation).
3. Detach the engine wiring harness from the
valve cover.
1. Unclip the power steering return line from the
engine wiring harness bracket.
2. Remove the air cleaner retaining bracket.
3. Unclip the engine wiring harness bracket
from the intake manifold.
2006.0 Fiesta 1212006 G451279en
procarmanuals.com

303-01 B-20 Engine - 2.OL Duratec-HE (M14) 303-01 B-20
GENERAL PROCEDURES
28. Install the air cleaner.
For additional information, refer to: Air
Cleaner
- 2.OL Duratec-HE (M14) (303-12
Intake Air Distribution and Filtering,
Removal and Installation).
29. Connect the battery ground cable.
For additional information, refer to: Battery
Disconnect
(414-01 Battery, Mounting and
Cables, General Procedures).
- --
2006.0 Fiesta 1212006 G451279en
procarmanuals.com

303-01 B-21 Engine - 2.OL Duratec-HE (M14) 303-01 B-21
IN-VEHICLE REPAIR
Intake Manifold(21 183 0)
Removal
1. Disconnect the battery.
For additional information, refer to: Battery
Disconnect (414-01 Battery, Mounting and
Cables, General Procedures).
2. Remove the air cleaner.
For additional information, refer to: Air
Cleaner
- 2.OL Duratec-HE (M14) (303-12
lntake Air Distribution and Filtering,
Removal and Installation).
3. Remove the right-hand headlamp.
6. Disconnect the generator electrical
connectors.
For additional information, refer to:
Headlamp Assembly (41 7-01 Exterior
Lighting, Removal and Installation). 7.
Remove the intake manifold lower retaining
4. Raise and support the vehicle. For additional bolt.
information, refer to: (I
00-02 Jacking and
Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
( 5. Disconnect the crankshaft position (CKP)
sensor electrical connector.
8. Remove the oil level indicator tube lower
retaining bolt.
2006.0 Fiesta 1212006 G451284en
procarmanuals.com

303-01 B-26 Engine - 2.OL Duratec-HE (M14) 303-01 B-26
IN-VEHICLE REPAIR
Crankshaft Pulley(21 572 0)
Special Tool(s)
I I Flange Holding Wrench, I
Universal
205-072
Adapter for 205-072
205-072-02
Alignment Tool, Camshaft
Alignment
303-376
Timing Peg, Crankshaft TDC
position
303-507
I I Pliers, Valve Stem Seal
General Equipment
I Bolt M6 x 18 mm I
Materials
Name
S~ecification
I Silicone sealant I WSE-M4G323-A4 I
Removal
I. Disconnect the battery.
For additional information, refer to: Battery
Disconnect (414-01 Battery, Mounting and
Cables, General Procedures).
2. Remove the air cleaner.
For additional information, refer to: Air
Cleaner
- 2.OL Duratec-HE (M14) (303-12
Intake Air Distribution and Filtering,
Removal and Installation).
3. Detach the engine wiring harness from the
valve cover.
1. Unclip the power steering fluid return line
from the retaining clips.
2. Remove the air cleaner retainer.
3. Unclip the engine wiring harness bracket at
the intake pipe.
4. Unclip the engine wiring harness at the intake
pipe.
2006.0 Fiesta 1212006 G451288en
procarmanuals.com

303-01 B-34 Engine - 2.OL Duratec-HE (M14) 303-01 B-34
IN-VEHICLE REPAIR
37. Install the EVAP valve bracket. 40. Attach the positive crankcase ventilation
(PCV) hose to the valve cover.
/- r.
38. Install the air cleaner retainer.
41. Attach the engine wiring harness to the
valve cover.
1. Clip on the engine wiring harness at the
intake pipe.
2. Clip on the engine wiring harness bracket at
the intake pipe.
3. Install the air cleaner retainer.
4. Connect the power. steering fluid return line
to the retaining clip.
42. Install the air cleaner.
For additional information, refer to: Air
Cleaner
- 2.OL Duratec-HE (M14) (303-12
Intake Air Distribution and Filtering,
Removal and Installation).
43. Connect the battery ground cable.
For additional information, refer to: Battery
Disconnect
(414-01 Battery, Mounting and
Cables, General Procedures).
2006.0 Fiesta 1212006 G451288en
procarmanuals.com