2007 FORD FIESTA transmission fluid

206-00-26 Brake System - General Information 206-00-26
DIAGNOSIS AND TESTING
TEST CONDITIONS DETAILSIRESU LTSIACTIONS
I J6: CHECK BRAKE PEDAL LINKAGE If
rn Disconnect the actuator rod from the pedal pin
and apply the brake pedal fully.
Did the pedal move freely?
-+ Yes
GO to J7.
+ No
REPAIR or INSTALL new brake pedal bush-
ings. REFER to: (206-06 Hydraulic Brake
Actuation)
Brake Pedal
- LHD, Vehicles With: Manual
Transaxle (Removal and Installation),
Brake Pedal
- LHD, Vehicles With: 4-Speed
Automatic Transmission
(AW81-40), Vehicles
With: Automated Gearshift (Removal and
Installation),
Brake Pedal
- RHD (Removal and Installation).
TEST the system for normal operation.
157: CHECK BRAKE PRESSURE CONTROL VALVE I
rn Check the brake pressure control valve for
contamination.
Is the brake fluid contaminated?
+ Yes
INSTALL a new brake pressure control valve.
FILL the brake master cylinder reservoir.
BLEED the brake system. REFER to: (206-00
Brake System
- General Information)
1 Brake System Bleeding (General Procedures),
Brake System Pressure Bleeding (General
Procedures). TEST the system for normal operation.
1 * Ehicle OK.
2006.0 Fiesta 1212006 G28494en
procarmanuals.com

206-00-28 Brake System - General Information 206-00-28
DIAGNOSIS AND TESTING
PINPOINT TEST L : SLOW OR INCOMPLETE BRAKE PEDAL RETURN
TEST CONDITIONS
DETAILSIRESU LTSIACTIONS /"'
I L1: CHECK FOR BRAKE PEDAL RETURN I[<.
Run the engine at fast idle while making several
brake applications. Pull the brake pedal rear-
ward with approximately 44.5 N
(1 0 lbs) force.
Release the brake pedal and measure the
distance to the floor pan. Make a hard brake
application. Release the brake pedal and
measure the brake pedal to floor pan distance.
The brake pedal should return to its original
position.
Did the brake pedal return to its original posi-
tion?
+ Yes
Vehicle OK.
+ No
GO to L2.
I L2: CHECK FOR BRAKE PEDAL BINDING
1 171 Check the brake pedal for free operation.
I Is the brake pedal operating freely?
+ Yes
I INSTALL a new brake booster. REFER to:
(206-07 Power Brake Actuation)
Brake Booster
- LHD (Removal and lnstallation),
Brake Booster
- RHD (Removal and lnstallation).
TEST the system for normal operation.
+ No
REPAIR or INSTALL new brake pedal bush-
ings. REFER to: (206-06 Hydraulic Brake
Actuation)
Brake Pedal
- LHD, Vehicles With: Manual
Transaxle (Removal and lnstallation),
Brake Pedal
- LHD, Vehicles With: 4-Speed
Automatic Transmission
(AW81-40), Vehicles
With: Automated Gearshift (Removal and
Installation),
Brake Pedal
- RHD (Removal and lnstallation).
TEST the system for normal operation.
Component Tests It is possible that all evidence of fluid leakage may
have washed off if the vehicle has been operated
in rain or snow, as brake fluid is water-soluble.
Hydraulic Leak Check Refill the system, bleed then apply the brakes
several times. Examine the system to verify that
NOTE:Thet-e is a common clutch and brake fluid
the reservoir fluid level is actually dropping. Locate
reservoir, therefore it is possible that a clutch leak
can lead to reduction in the reservoir level.
-- --
2006.0 Fiesta 1212006 G28494en
procarmanuals.com

21 1-02-2 Power Steering 21 1-02-2
SPECIFICATIONS
Toraue S~ecifications
Description
Steering gear mounting bolts
Power steering line to steering gear valve body
clamp retaining bolt
Power steering line bracket to steering gear
retaining bolt
Power steering line to cylinder head support bracket
retaining bolt (Duratec)
Power steering line to accessory drive belt support 25
bracket retaining bolt (Duratec)
Power steering lines to transaxle bracket retaining
bolt
- vehicles with 1.6L Duratorq-TDCi (DV) Diesel
I Power steering supply hose to engine block (rear) I 25 I 18 I - I
Power steering line to transmission housing
retaining bolt
Power steering line to engine block (front)
- vehicles
with
1.4L Duratorq-TDCi (DV) Diesel without air
conditioning
Power steering line to power steering pump union
- vehicles with 1.3L Duratec-8V (Rocam)
Power steering line to power steering pump union
- vehicles with 1.4L Duratec-I 6V (Sigma), 1.6L
Duratec-1 6V (Sigma) or 2.OL Duratec-HE (M14)
Power steering line to power steering pump union
- vehicles with 1.4L Duratorq-TDCi (DV) Diesel
Power steering line to power steering pump union
- vehicles with 1.6L Duratorq-TDCi (DV) Diesel
Power steering pump to steering gear pressure line
support bracket to inlet manifold retaining nut
-
vehicles with 2.OL Duratec-HE (M14)
Power steering pump retaining bolts - vehicles with
1.3L Duratec-8V (Rocam)
Power steering pump retaining bolts - vehicles with
1.4L Duratec-1 6V (Sigma), 1.6L Duratec-1 6V
(Sigma) or 2.OL Duratec-HE (M14)
Power steering pump retaining bolts - vehicles with
1.4L Duratorq-TDCi (DV) Diesel
Power steering pump retaining nuts
- vehicles with
1.6L Duratorq-TDCi (DV) Diesel
Power steering fluid cooler line to front bumper left-
hand retaining bolt
Power steering fluid cooler line to front bumper
right-hand retaining bolt
2006.0 Fiesta 1212006 GI 05647en
procarmanuals.com

21 1 -02-25 Power Steering 21 1 -02-25
REMOVAL AND INSTALLATION
Remove the exhaust hanger insulator. 11. Remove the front axle crossmember
retaining bolts on both sides.
8. N0TE:Use a 5 mm Allen key to prevent the
stabilizer bar link ball joint from rotating.
12. Lower the front axle crossmember
Detach the stabilizer bar link from the approximately
100 mm.
stabilizer bar on both sides.
13. Detach the steering gear to power steering
fluid reservoir return line from the power
steering pump to steering gear pressure
line.
9. Remove the engine support insulator.
10. Using a transmission jack and a wooden
block, support the front axle crossmember.
14' ~CAUTION:C~~ the steering gear valve
body inlet port and outlet port to prevent
fluid loss or dirt ingress.
Disconnect the power steering lines from the
steering gear valve body.
1. Remove the power steering lines clamp plate
retaining bolt.
2. Rotate the power steering lines clamp plate.
2006.0 Fiesta 1212006 G458165en
procarmanuals.com

21 1 -02-30 Power Steering 21 1 -02-30
REMOVAL AND INSTALLATION
Steering Gear to Power Steering Fluid Reservoir Return Line -
2.OL Duratec-HE (M14) RHD (' ,
Centralize the steering and lock it in position. table(s).
Special Tool(s)
2006.0 Fiesta 1212006 G458167en
2. Detach the steering column shaft from the
steering gear pinion.
Discard the steering column shaft to steering
gear pinion retaining bolt.
Pp
205524
24003
Alignment Pins, Subframe
205-524
Removerllnstaller, Hose
Clamp
303-397
General Equipment
Transmission jack 3. Remove the front wheels and tires.
Materials For
additional information, refer to: Wheel
and Tire (204-04 Wheels and Tires, Removal
Name Specification and Installation).
4. Lower the vehicle.
Grease
1. N0TE:Make sure that the road wheels are in 5. Remove the components in the order
the straight ahead position.
indicated in the following illustration(s) and
SA-M 1 C9107-A
procarmanuals.com

21 1-02-35 Power Steering 21 1-02-35
REMOVAL AND INSTALLATION
Item 6 Steering gear to power steering fluid 2. N0TE:Use the front axle crossmember rear
reservoir return line inner
retaining bolts to locate the special
I tools. I, Install new O-ring seals onto the power
steering lines.
N0TE:Do not fully tighten the front axle
crossmember rear inner retaining bolts at this
stage.
Using a transmission jack, wooden block
and the special tools, position and align the
front axle crossmember.
2. Connect the power steering lines to the
steering gear valve body.
1. Rotate the power steering lines clamp plate.
2. Install the power steering lines clamp plate
retaining bolt.
3a &AUTION:W~~I~ tightening the front axle
crossmember front retaining bolts and the
i front axle crossmem ber rear outer retaining
bolts, make sure that the front axle
crossmember does not move.
Ifem 5 Cable ties
1. Attach the steering gear to power steering
fluid reservoir return line to the power
steering pump to steering gear pressure line. Install
the front axle crossmember front
retaining bolts and the front axle
crossmember rear outer retaining bolts on
both sides.
2006.0 Fiesta 1212006 G458167en
procarmanuals.com

21 1 -02-38 Power Steering 21 1 -02-38
REMOVAL AND INSTALLATION
Steering Gear(l3 11 6 0)
I I Separator, Ball Joint Discard
the retaining bolt.

3. Remove the wheels and tires.
I I I For additional information, refer to: Wheel I I I
General Equipment I I
and Tire (204-04 Wheels and Tires, Removal
and Installation).
Removal
All vehicles
Transmission jack 1 4. Disconnect the power steering fluid reservoir
I. N0TE:Make sure that the road wheels are in
the straight ahead position.
Materials
Centralize the steering and lock
it in position. return
hose quick release coupling.
2. Detach the steering column shaft from the
steering gear pinion.
return hose quick release coupling.
Allow the fluid to drain into a suitable
container.
Name Specification 1. Press the power steering fluid reservoir return
5m &AUTION:O~~~ bending of the exhaust
flexible pipe may cause damage resulting in
failure.
2006.0 Fiesta 1212006 GI 05648en
hose quick release coupling locking tangs.
Grease
2. Disconnect the power steering fluid reservoir ( SA-M 1 C9107-A
procarmanuals.com

211 -02-41 Power Steering 21 1-02-41
REMOVAL AND INSTALLATION
15. Detach the power steering lines from the 19. Lower the front axle crossmember to gain
steering gear (left-hand drive shown). access
to the steering gear.
i 20. Remove the steering gear.
16. Disconnect the power steering lines from
the steering gear valve body.
1. Remove the retaining bolt.
2. Rotate the clamp plate.
Allow the fluid to drain into a suitable
container.
Discard the O-ring seals.
17.
Using a transmission jack and a wooden
block, support the front axle crossmember.
18. Remove the front axle crossmember
retaining bolts on both sides.
21. Remove and discard the steering gear
bulkhead floor seal.
22. Remove the exhaust heat shield.
2006.0 Fiesta 1212006 GI 05648en
procarmanuals.com