Page 1024 of 1226
Automatic Transmission/Transaxle -
Vehicles With: 4-Speed Automatic
Transmission
(AW81-40)
REMOVAL AND INSTALLATION
10. Disconnect the transaxle wiring harness
14. Detach the selector lever cable from the
electrical connector. manual shift lever.
f
11. Disconnect the transmission range (TR)
15. Detach the selector lever cable retaining
sensor electrical connector.
bracket from the transaxle and position
it
to one side.
12. Disconnect the vehicle speed sensor
(VSS)
electrical connector.
16. Remove the transmission fluid level
indicator tube.
13. Remove the front wheels and tires.
For additional information, refer to: Wheel
and Tire (204-04 Wheels and Tires,
Removal and Installation).
2006.0 Fiesta 1212006 G371506en
procarmanuals.com
Page 1034 of 1226
Automatic Transmission/Transaxle -
Vehicles With: 4-Speed Automatic
Transmission (AW81-40)
REMOVAL AND INSTALLATION
32. Lower the vehicle.
36. Connect the transaxle breather hose.
33. Connect the vehicle speed sensor (VSS)
electrical connector.
34. Connect the transmission range (TR)
sensor electrical connector.
35. Connect the transaxle wiring harness
electrical connector. 37. Connect
the turbine shaft speed (TSS)
sensor electrical connector.
I I
38. Attach the ground cable to the transaxle.
2006.0 Fiesta 1212006 G371506en
procarmanuals.com
Page 1036 of 1226

Automatic Transmission/Transaxle -
Vehicles With: 4-Speed Automatic
307-01 -76 Transmission
(AW81-40) 307-01 -76
REMOVAL AND INSTALLATION
46. Install the battery tray.
For
additional information, refer to: Battery
Tray (414-01 Battery, Mounting and
Cables, Removal and Installation).
47. Connect the powertrain control module
(PCM) electrical connector to the PCM.
For
additional information, refer to:
Powertrain
Control Module (PCM) - 1.25L
Duratec-1 6V (Sigma)ll.4L Duratec-1 6V
(Sigma)ll .6L Duratec-1 6V (Sigma) (303-1 4
Electronic Engine Controls, Removal and
Installation).
48. Install the air cleaner.
For additional information, refer to: Air
Cleaner - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll.GL Duratec-1 6V
(Sigma) (303-1 2 Intake Air Distribution
and
Filtering, Removal and Installation).
49. Check the transmission fluid level and top
up with
clean automatic transmission fluid
if necessary.
For
additional information, refer to:
Transmission
Fluid Level Check (307-01
Automatic
Transmission/Transaxle -
Vehicles With: 4-Speed Automatic
Transmission
(AW81-40), General
Procedures).
50.
N0TE:Only carry out the following step
when a new
transaxle has been installed.
Using worldwide diagnostic system (WDS),
reset the transmission control module (TCM).
2006.0 Fiesta 1212006 G371506en
procarmanuals.com
Page 1050 of 1226
Automatic Transmission/Transaxle External
Controls -Vehicles With:
4Speed Automatic
307-05-6 Transmission (AW81-40) 307-05-6
REMOVAL AND INSTALLATION
Brake Shift Interlock Actuator
Removal
1. Remove the floor console. 3. Install the bolt.
2. Disconnect the overdrive (OID) switch
electrical connector (selector lever assembly
shown removed for clarity).
3. Remove the brake shift interlock actuator.
1. Remove the bolt.
2. Remove the knob.
3. Remove the brake shift interlock actuator.
Installation
1. Install the brake shift interlock actuator.
1. Install the brake shift interlock actuator.
2. Position the knob.
2. Connect the OID switch electrical connector
(selector lever assembly shown removed for
clarity).
3. Install the floor console.
2006.0 Fiesta 1212006 G294547en
procarmanuals.com
Page 1054 of 1226
Automatic Transmission/Transaxle External
Controls -Vehicles With:
4Speed Automatic
Transmission
(AW81-40)
REMOVAL AND INSTALLATION
Selector Lever
Removal
1. Remove the floor console. 4. Remove the transmission selector lever.
2. Detach the selector lever cable from the
transmission selector lever.
1. Shift the selector lever to the "P" (PARK)
position.
2. Detach the selector lever cable.
3. Pull the selector lever cable locking pin and
detach the selector lever cable outer sleeve.
3.
Disconnect the transmission selector lever
electrical connector.
Installation
1. Install the transmission selector lever.
2. Connect the transmission selector lever
electrical connector.
3. Attach the selector lever cable to the
transmission selector lever.
2006.0 Fiesta 1212006 G294549en
procarmanuals.com
Page 1057 of 1226
Automatic TransmissionlTransaxle External
Controls -Vehicles With: 4-Speed Automatic
307-05-1
3 Transmission (AW81-40) 307-05-1 3
REMOVAL AND INSTALLATION
Selector Lever Knob
, > .
Removal
1. Remove the floor console.
2. Disconnect the overdrive (OID) switch
electrical connector (selector lever assembly
shown removed for clarity).
3. Remove the selector lever knob.
Remove the bolt. i
Installation
1. Install the selector lever knob.
Position the knob.
lnstall the bolt.
2. Connect the OID switch electrical connector
(selector lever assembly shown removed for
clarity).
3. Install the floor console.
2006.0 Fiesta 1212006 G294551 en
procarmanuals.com
Page 1058 of 1226
Automatic Transmission/Transaxle External
Controls -Vehicles With: 4-Speed Automatic
307-05-1 4 Transmission (AW81-40) 307-05-1 4
DISASSEMBLY AND ASSEMBLY
Selector Lever
Materials Unclip the lamp.
I I Name S~ecification
1 Grease I S-MlC1021-A I
Disassembly
N0TE:Use vice jaw protectors for all work to be
done in the vice.
1. Disconnect the overdrive (OID) switch
electrical connector.
Assembly
1. To assemble, reverse the disassembly
procedure.
Coat all sliding and turning parts with grease.
2. Remove the selector lever knob.
Remove the bolt.
3. Disassemble the selector lever.
Remove the brake shift interlock actuator.
Remove the selector lever bezel.
Unclip the bezel.
2006.0 Fiesta 1212006 G388014en
procarmanuals.com
Page 1112 of 1226
308-03-22 Manual Transmission/Transaxle 308-03-22
IN-VEHICLE REPAIR
Vehicle Speed Sensor (VSS)(33 654 0)
Removal 2. Insert the retaining pin.
I. Raise and support the vehicle. For additional
information, refer to:
(1 00-02 )
Jacking (Description and Operation),
Lifting (Description and Operation).
2. Disconnect the vehicle speed sensor (VSS)
electrical connector.
3. Remove the VSS.
I. Remove the retaining pin.
2. Remove the VSS.
2. Install VSS connector.
3. Lower the vehicle.
Installation
1. Install VSS.
1. Insert the VSS.
2006.0 Fiesta iuzoos GI 81 04en
procarmanuals.com