2007 FORD FIESTA boot

205-0414 Front Drive Halfshafts 205-04-4
DIAGNOSIS AND TESTING
Front Drive Halfshafts
Inspection and Verification 3. If an obvious cause for an observed or reported
concern is found, correct the cause (if possible) c.# '
1. Verify the customer concern. before proceeding
to the next step.
2. Visually inspect for obvious signs of mechanical
or electrical damage.
Symptom Chart - Front Drive Halfshafts
Symptom Chart
Symptom
Possible Sources Action
Clicking, Popping or Grinding
Noises While Turning Inadequate or contaminated INSPECT, CLEAN and
I lubricant in the inner or outer I LUBRICATE as necessary.
I Outer Constant Velocity (CV)
I Joint Boot - in this section.
front drive halfshaft constant
velocity (CV) joint.
REFER to Constant
Velocity (CV) Joint Boot -
Wheel bearings, brakes,
suspension or steering
components.
Another component contacting
front drive halfshaft assembly.
--
INSPECT and REPAIR as
necessary. REFER to
Section 204-00 [Suspension
System
- General Information]
1 206-00 [Brake System -
General Information] I 21 1-00
[Steering System
- General
Information].
INSPECT and REPAIR as
necessary.
- --
Vibration at Highway Speeds
Shudder Vibration During
Acceleration. Out of balance front wheels or
tires. Balance wheels and tires as
necessary.
I Incorrectly seated outer I REPAIR or INSTALL new as I
Out-of-round tires.
constant velocity (CV) joint in necessary.
front wheel hub.
I REFER to Halfshaft LH -
REPAIR or INSTALL new as
necessary.
I I I Halfshaft RH - in this section. I
Excessively high CV joint
operating angles caused by
incorrect ride height. CHECK the ride height,
VERIFY correct spring rate.
CHECK items under Halfshaft
Joint Pullout. REPAIR or INSTALL
new as necessary.
Excessively worn or damaged
I inner or outer front drive half-
- - - - --
2006.0 Fiesta 1212006 G25403en
INSPECT and INSTALL new
as necessary.
shaft constant velocity (CV)
joint. REFER
to Halfshaft LH
-
I Halfshaft RH - in this sectionk 1;
procarmanuals.com

205-04-1 1 Front Drive Halfshafts 205-04-1 1
REMOVAL AND INSTALLATION
N0TE:Do not damage the inner constant velocity 1. Slide a small screwdriver under the boot seat
(CV) joint boot. to allow the air to escape.
N0TE:Discard the grease.
Remove the halfshaft.
Remove and discard the constant velocity
(CV) joint boot clamp.
Installation
Im &AUTION:T~~ total amount of grease
must not exceed
100 grams.
i Apply grease to the intermediate shaft.
*' &AUTION:S~~~~~~ the halfshaft. The inner
joint must not be bent more than
18 degrees.
The outer joint must not be bent more than
45 degrees.
Attach the halfshaft to the intermediate shaft.
3. N0TE:Do not damage the inner constant
velocity (CV) joint boot.
N0TE:Make sure that the intermediate shaft mating
surface for the joint boot is clean.
2. Insert the constant velocity (CV) joint in as
far as it will go, then pull it back
approximately
20 mm.
4. N0TE:lnstall a new CV joint boot clamp.
Using a suitable grip wrench, install the inner
CV joint boot clamp.
5m ~CAUTION:M~~~ sure the halfshaft is
completely installed into the wheel hub.
Using the special tool, install the halfshaft.
Install the inner constant velocity (CV) joint
boot (halfshaft shown removed for clarity).
6. N0TE:lnstall a new wheel hub retaining nut.
2006.0 Fiesta 1212006 GI 131 05en
procarmanuals.com

205-04-1 5 Front Drive Halfshafts 205-04-1 5
REMOVAL AND INSTALLATION
Inner Constant Velocity (CV) Joint Boot(l4 336 0)
Special Tool(s)
I I Clamping Tool, Boot I
Remover, BearingIGear
205-3 1 0 (1 5-09 1
A~se vise jaw protectors for all operations
in a vise.
N0TE:Secure the halfshaft in a vise.
Detach the inner CV joint housing from the
halfshaft.
1. Remove and discard the CV joint boot
retaining clamps.
2. Remove the CV joint housing and discard
the grease.
I I Installer, Extension Housing I
BushingIOil Seal
308-046 (1 6-0 1 6)
Materials
Name Specification
1 Grease I WSS-M 1 C259A1 I
4. Remove and discard the spider circlip.
Removal 5. Using the special tool, remove the spider.
I. Remove the right-hand halfshaft.
For additional information, refer to Halfshaft
RH in this section.
2. Remove the left-hand halfshaft.
For additional information, refer to Halfshaft
LH in this section.
3. CAUTIONS:
ADO not bent the inner constant velocity
(CV) joint more than
18 degrees and the outer
CV joint more than
45 degrees.
2006.0 Fiesta 1212006 GI 52548en
procarmanuals.com

205-04-1 6 Front Drive Halfshafts 205-04-1 6
REMOVAL AND INSTALLATION
6. Remove the inner CV joint boot. 3. N0TE:lnstall the spider with the chamfer
Mark the halfshaft were the CV joint boot is facing towards the halfshaft.
located. Using the special tool, install the spider. (
installation 4. N0TE:lnstall a new spider circlip.
I. N0TE:Make sure that the inner constant Install the spider circlip.
velocity (CV) joint boot is installed to the
marks on the halfshaft.
Install the inner CV joint boot.
'' ACAUTION:T~~ total amount of grease in
the inner CV joint must not exceed
85 grams.
Apply grease to the inner CV joint boot.
2. N0TE:lnstall a new CV joint boot retaining I I
clamp.
Using the special tool, install the CV joint
boot retaining clamp.
6. Attach the inner CV joint housing to the
halfshaft (left hand side shown for clarity).
2006.0 Fiesta iu200s GI 52548en
procarmanuals.com

205-04-1 7 Front Drive Halfshafts 205-04-1 7
REMOVAL AND INSTALLATION
1. Use a suitable screwdriver under the CV joint
boot to allow air to escape.
2. Install the CV joint boot housing and pull it
backwards
20 mm.
7. N0TE:lnstall a new CV joint boot retaining
clamp.
N0TE:Make sure that the CV joint boot is clamped
at the measured
postion.
Using a special tool, install the CV joint boot
retaining clamp.
8. Install the right-hand halfshaft.
For additional information, refer to Halfshaft
RH in this section.
9. Install the left-hand halfshaft.
For additional information, refer to Halfshaft
LH in this section.
2006.0 Fiesta 1212006 GI 52548en
procarmanuals.com

205-04-1 8 Front Drive Halfshafts 205-04-1 8
REMOVAL AND INSTALLATION
Outer Constant Velocity (CV) Joint Boot(l4 338 0)
Special Tool(~)
I
-
I Clamping Tool, Boot
Retaining Clamp
204-1 69 (1 4-044)
14044
Materials
Name Specification
1 Grease I WSS-MI ~259-v
Remove and discard the grease. I
Removal Installation
&AUTION:The outer constant velocity I' ~CAUTION:T~~ total amount of grease in
(CV) joint is a press fit. Do not disassemble. the
inner constant velocity (CV) joint must
Failure to follow this instruction may result not
exceed
85 grams.
in damage to the outer CV joint.
Apply grease to the outer CV joint boot.
Remove the inner CV joint boot.
For additional information, refer to Inner
Constant Velocity (CV) Joint Boot in this
section.
2. CAUTIONS:
ADO not bent the inner CV joint more than
18 degrees and the outer CV joint more than
45 degrees.
n~se vise jaw protectors for all operations
in a vise.
N0TE:Secure the halfshaft in a vise.
N0TE:Mark the halfshaft were the CV joint boot is *. Install the Outer CV joint boot=
located.
Use a suitable screwdriver under the boot to
Remove the outer CV joint boot. allow air to escape.
Remove and discard the CV joint boot
retaining clamps.
2006.0 Fiesta 1212006 GI 52549en
procarmanuals.com

205-04-1 9 Front Drive Halfshafts 205-04-1 9
REMOVAL AND INSTALLATION
3. N0TE:Make sure that the outer CV joint boot
is installed to the marks on the halfshaft.
N0TE:lnstall a new inner CV joint boot retaining
clamp.
Using the special tool, install the inner CV
joint boot retaining clamp.
4. N0TE:lnstall a new outer CV joint boot
retaining clamp.
Using the special tool, install the outer CV
joint boot retaining clamp.
5. Install the inner CV joint boot.
For additional information, refer to Inner
Constant Velocity (CV) Joint Boot in this
section.
2006.0 Fiesta 1212006 GI 52549en
procarmanuals.com

206-02-7 Drum Brake 206-02-7
REMOVAL AND INSTALLATION
Brake Shoes(l2 285 0)

Materials 5. Detach the wheel speed sensor from the
backing plate.
Name Specification
Silicon dielectric
compound
Removal
I. Remove the parking brake control trim panel.
Grease - brake shoe
adjuster
2. Loosen the parking brake cable adjustment
nut to the end of the thread.
SAM-1 C1024-A
Discard the retaining clip.
6. Remove the brake drum.
7. Remove the hold down springs.
3. Release the parking brake.
4. Remove the wheel and tire. For additional
information, refer to Section
204-04 [Wheels
and Tires]. *' ACAUTION:DO not damage the wheel
cylinder boots.
N0TE:Hold the wheel cylinder pistons in place with
a rubber band.
2006.0 Fiesta 1212006 GI 49887en
procarmanuals.com