2007 FORD FIESTA boot

303-01 B-29 Engine - 2.OL Duratec-HE (M14) 303-01 B-29
IN-VEHICLE REPAIR
Remove and discard the CV joint boot clamp. 5. Install the special tool.
Installation 6. Raise the vehicle. For additional information,
refer to: (1 00-02 Jacking and Lifting)
1. N0TE:lnstall a new front friction washer.
Jacking (Description and Operation),
Install the front friction washer (engine
Lifting (Description and Operation).
shown removed for clarity).
7. Remove the cylinder block lower blanking
plug and install the special tool.
2. Install the crankshaft front seal.
For additional information, refer to:
8. N0TE:Only rotate the crankshaft in the
Crankshaft Front Seal (303-01 Engine - 2.OL normal direction of rotation.
Duratec-HE (M14), In-vehicle Repair).
Rotate the crankshaft using the crankshaft
3. Lower the vehicle.
pulley bolt until the crankshaft contacts the
4. N0TE:Only rotate the camshafts in the special
tool.
normal direction of rotation.
Carefully rotate the camshafts using a
spanner until the cams of cylinder no. 4 are
positioned at the valve overlap.
2006.0 Fiesta 1212006
procarmanuals.com

303-01 B-32 Engine - 2.OL Duratec-HE (M14) 303-01 B-32
IN-VEHICLE REPAIR
24. Raise the vehicle. For additional N0TE:Make sure that the contact surface for the
information, refer to: (100-02 Jacking and CV joint boot on the intermediate shaft is clean. ,
Lifting)
Slide the inner CV joint boot onto the
Jacking (Description and Operation),
intermediate shaft. (..
Lifting (Description and Operation). Use a suitable screwdriver under the boot to
25. Remove the M6 x 18 mm bolt. allow air to escape.
26. Remove the special tool. 29. N0TE:lnstall a
new boot clamp.
Using a suitable grip wrench, install the inner
CV joint boot clamp.
27. Install the cylinder block lower blanking
plug.
30. N0TE:When installing a new engine front
cover, the crankshaft position sensor
(CKP
sensor) must be aligned using the tool
supplied.
28.
N0TE:Do not damage the boot of the inner
CV joint. Align
the
CKP sensor (engine shown
removed for clarity).
1. Loosen the CKP sensor bolts.
2006.0 Fiesta 1212006 G451288en
procarmanuals.com

303-01 B-41 Engine - 2.OL Duratec-HE (M14) 303-01 B-41
IN-VEHICLE REPAIR
12. Raise and support the vehicle. For Remove and discard the constant velocity
additional information, refer to: (1 00-02 (CV) joint boot clamp.
I Jacking and Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
13. Disconnect the crankshaft position (CKP)
sensor electrical connector.
14. Disconnect the generator electrical
connectors.
Unclip the wiring harness.
16. N0TE:Only rotate the crankshaft in the
normal direction of rotation.
Rotate the crankshaft until piston No.
1 is
approximately 45 degrees before top dead
center (BTDC).
15.
N0TE:Do not damage the inner constant
velocity (CV) joint boot.
Detach the inner CV joint boot from the
intermediate shaft.
2006.0 Fiesta 1212006 G451293en
procarmanuals.com

303-01 B-46 Engine - 2.OL Duratec-HE (M14) 303-01 B-46
IN-VEHICLE REPAIR
23. Remove the special tool.
21. Raise and support the vehicle. For 26. Install the engine front cover lower blanking
additional information, refer to:
(I 00-02 plug.
27. N0TE:Do not damage the inner constant
velocity (CV) joint boot.
Jacking
and Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
22. Remove the crankshaft pulley securing bolt.
N0TE:Make sure that the intermediate shaft mating
surface for the
CV joint boot is clean.
ELE0021907
Attach the inner CV joint boot to the
intermediate shaft.
24. Install the cylinder block lower blanking
plugB 28. N0TE:lnstall a new CV joint boot clamp.
25. Coat the engine front cover lower blanking
plug with sealant. Using
a suitable grip wrench, install the inner
CV joint boot clamp.
2006.0 Fiesta 1212006 G451293en
procarmanuals.com