2007 FORD FIESTA wheel

206-09A-1 I Anti-Lock Control 206-09A-I 1
REMOVAL AND INSTALLATION
Hydraulic Control Unit (HCU) - Vehicles Built From: 0512004
/ ! Remove the brake master cylinder to HCU
Materials brake tubes.
Name Specification
I Super DOT 4 brake fluid I ESD-M6C57-A I
Removal
All vehicles
A CAUTI0N:If brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
1. Detach the engine wiring harness electrical
connector from the wheelhouse assembly.
Right-hand drive vehicles
4. Remove the battery tray.
For additional information, refer to: Battery
Tray (414-01 Battery, Mounting and Cables,
Removal and Installation).
5. CAUTIONS:
hap the brake tubes to prevent fluid loss
or dirt ingress.
nplug the hydraulic control unit (HCU)
ports to prevent fluid loss or dirt ingress.
Left-hand drive vehicles N0TE:Make a note of the position of the brake
2. Remove the brake master cylinder. tubes to aid installation.
For additional information, refer to: Brake Disconnect
the brake master cylinder to HCU
Master Cylinder
- LHD (206-06 Hydraulic brake tubes
from the HCU.
Brake Actuation, Removal and Installation).
I
3. CAUTIONS: I
hap the brake tubes to prevent fluid loss
or dirt ingress.
nplug the hydraulic control unit (HCU)
ports to prevent fluid loss or dirt ingress.
N0TE:Make a note of the position of the brake
tubes to aid installation.
All vehicles
6. CAUTIONS:
&ap the brake tubes to prevent fluid loss
or dirt ingress.
2006.0 Fiesta 1212006 G406271 en
procarmanuals.com

206-09A-14 Anti-Lock Control 206-09A-I 4
REMOVAL AND INSTALLATION
Anti-Lock Brake System (ABS) Module - Vehicles Built Up To: /.
Materials Remove
the brake master cylinder to
hydraulic control unit (HCU) brake tubes.
Name
S~ecification
I Super DOT 4 brake fluid 1 ESD-M6C57-A I
Removal
A CAUTI0N:Y brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
1. Remove the brake master cylinder. For
additional information, refer to
Section
206-06 [Hydraulic Brake Actuation].
2. Detach the engine wiring harness electrical
connector from the wheelhouse assembly.
4m CAUTIONS:
3. CAUTIONS:
&ap the brake tubes to prevent fluid loss
or dirt ingress.
Aplug the hydraulic control unit (HCU)
ports to prevent fluid loss or dirt ingress.
N0TE:Make a note of the position of the brake
tubes, to aid installation.
&ap the brake tubes to prevent fluid loss
or dirt ingress.
Aplug the HCU ports to prevent fluid loss
or dirt ingress.
N0TE:Make a note of the position of the brake
tubes, to aid installation.
Disconnect the brake tubes from the HCU.
2006.0 Fiesta 1~12006 G327317en
procarmanuals.com

206-09A-I 7 Anti-Lock Control 206-09A-I 7
REMOVAL AND INSTALLATION
Anti-Lock Brake System (ABS) Module - Vehicles Built From:
0512004
Materials Remove
the brake master cylinder to HCU
brake tubes.
Name Specification
I Super DOT 4 brake fluid I ESD-M6C57-A I
Removal
All vehicles
A CAUTI0N:lf brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
1. Detach the engine wiring harness electrical
connector from the wheelhouse assembly.
Left-hand drive vehicles
2. Remove the brake master cylinder.
For additional information, refer to: Brake
Master Cylinder
- LHD (206-06 Hydraulic
Brake Actuation, Removal and Installation).
3. CAUTIONS:
&ap the brake tubes to prevent fluid loss
or dirt ingress.
Aplug the hydraulic control unit (HCU)
ports to prevent fluid loss or dirt ingress.
N0TE:Make a note of the position of the brake
tubes to aid installation.
Right-hand drive vehicles
4. Remove the battery tray.
For additional information, refer to: Battery Tray (41 4-01 Battery, Mounting and Cables,
Removal and Installation).
5. CAUTIONS:
hap the brake tubes to prevent fluid loss
or dirt ingress.
nplug the hydraulic control unit (HCU)
ports to prevent fluid loss or dirt ingress.
N0TE:Make a note of the position of the brake
tubes to aid installation.
Disconnect the brake master cylinder to HCU
brake tubes from the HCU.
All vehicles
6. CAUTIONS:
2006.0 Fiesta 1212006 G406272en
procarmanuals.com

206-09A-20 Anti-Lock Control 206-0949-20
REMOVAL AND INSTALLATION
Rear Wheel Speed Sensor(l2 785 0)
Removal
All vehicles
I. Raise and support the vehicle. For additional
information, refer to: (100-02 Jacking and
Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
Vehicles with rear drum brakes
2. Detach the wheel speed sensor from the
wheel spindle on both sides.
Vehicles with rear disc brakes
3. Detach the wheel speed sensor from the
wheel spindle on both sides.
4. Detach the wheel speed sensor wiring
harness from the wheel speed sensor wiring
harness support bracket on both sides.
All vehicles
5. Disconnect the wheel speed sensor electrical
connector.
6. Detach the wheel speed sensor support
bracket and wheel speed sensor wiring
harness from the beam axle.
Discard the retaining clips.
2006.0 Fiesta 1212006 GI 83775en
procarmanuals.com

206-09A-21 Anti-Lock Control 206-09A-21
REMOVAL AND INSTALLATION
7. Detach the wheel speed sensor wiring
harness from the wheel speed sensor
/ 1 support bracket.
Discard the retaining clips.
8. Detach the wheel speed sensor wiring
harness from the beam axle on both sides.
9. Remove the rear wheel speed sensor.
Installation
I. N0TE:lnstall new retaining clips.
To install, reverse the removal procedure.
2006.0 Fiesta 1212006 GI 83775en
procarmanuals.com

206-09A-22 Anti-Lock Control 206-09A-22
REMOVAL AND INSTALLATION
Rear Wheel Speed Sensor Ring(l2 788 0)
Special Tool(s)
I I Installer, ABS Sensor Ring I
General Eaui~ment
I Soft faced hammer I
Removal
Remove and discard the wheel hub retaining \.
nut.
Vehicles with rear drum brakes
All vehicles
1. Remove the brake drum. 5. Remove and discard the wheel speed sensor
For additional information, refer to: Brake ring
(brake disc shown).
Drum
(206-02 Drum Brake, Removal and
Installation).
Vehicles with rear disc brakes
2. Remove the dust cap.
Installation
All vehicles
1. CAUTIONS:
AMake sure the wheel speed sensor ring 3. Remove the brake disc.
is not knocked, damaged and kept free from
For additional information, refer to: Brake metal
fragments.
Disc
(206-04 Rear Disc Brake, Removal and
Installation).
A~rotect the face of the wheel speed
sensor ring with a non-ferrous flat block to
4. Remove the wheel hub.
prevent damage.
AMake sure the wheel hub or brake drum
is adequately supported and do not allow
it
to rest on the wheel studs. f
AMake sure the wheel speed sensor ring ''- '
is pressed on slowly and squarely until fully
seated.
ADO not exceed a maximum load of 10 kN.
2006.0 Fiesta 1212006 GI 83776en
procarmanuals.com

Anti-Lock Control
REMOVAL AND INSTALLATION
Using the special tool, install a new wheel Using
a soft faced hammer and a wooden
/ speed sensor ring (brake disc shown). block,
install the dust cap.
Vehicles with rear disc brakes
2. CAUTIONS:
AAvoid any impact on the wheel speed
sensor ring.
n~ake sure the wheel speed sensor ring
is clean.
A~void any contact between the wheel
, speed sensor ring and a magnetic surface.
( , A~otate the hub assembly 10 times
counterclockwise when tightening the wheel
hub retaining nut to prevent damage to the
wheel bearing.
Vehicles with rear drum brakes
5. CAUTIONS:
AAvoid any impact on the wheel speed
sensor ring.
AMake sure the wheel speed sensor ring
is clean.
AAvoid any contact between the wheel
speed sensor ring and a magnetic surface.
Install the brake drum.
For additional information, refer to: Brake
Drum (206-02 Drum Brake, Removal and
Installation).
N0TE:lnstall a new wheel hub retaining nut.
Install the wheel hub.
3. Install the brake disc.
For additional information, refer to: Brake
Disc (206-04 Rear Disc Brake, Removal and
Installation).
4.
N0TE:lf the dust cap is damaged a new dust
cap must be installed.
2006.0 Fiesta 1212006 GI 83776en
procarmanuals.com

206-09A-24 Anti-Lock Control 206-0944-24
REMOVAL AND INSTALLATION
Front Wheel Speed Sensor(l2 784 0)
Removal Remove the wheel speed sensor bolt. (.
1. Remove the wheel and tire.
For additional information, refer to: Wheel
and Tire
(204-04 Wheels and Tires, Removal
and Installation).
2. Detach the fender splash shield from the
wheelhouse assembly.
3' &AUTION:M~~~ sure that the area around
the component is clean and free of foreign
material.
I. Detach the wheel speed sensor electrical
connector from the wheelhouse assembly.
2. Disconnect the wheel speed sensor electrical
connector. 5.
N0TE:Make sure that
all openings are sealed.
N0TE:Note the position of the component before
removal.
Remove the wheel speed sensor.
Installation
&AUTION:M~~~ sure that the wheel speed
sensor cable is not twisted and correctly
located.
N0TE:Make sure that the sensor housing is clean
and free of foreign material.
N0TE:Make sure that the sensor is installed in the
same location as when removed.
4m ~CAUTION:M~~~ sure that the area around To
install, reverse the removal procedure.
the component is clean and free of foreign
material.
2006.0 Fiesta 1212006 G913895en
procarmanuals.com