2007 FIAT ULYSSE Owners Manual

GETTING TO KNOW YOUR CAR
88
To prevent the vehicle from moving
accidentally, release the handbrake
with the foot brake pedal depressed.
IMPORTANTThe handbrake
lever A is fitted with a safety device
which prevents the handbrake disen-
gaging when button Bis pressed with
the lever pulled. Therefore, to release
the handbrake, not only press button
B, but also pull the lever Aupwards
so that the safety device is released,
then lower the lever.When the handbrake lever is en-
gaged, if you pull button B-fig. 108
forward and then you lower the lever,
the vehicle is still braked.CRUISE CONTROL
(where fitted) fig. 109
GENERAL
This is an electronic device (CRUISE
CONTROL) which makes it possible
to maintain vehicle cruising speed con-
stant without using any of the tradi-
tional controls except for the steer-
ing wheel. Thus, the engine taxing on
road is reduced, especially during long
journeys, because the stored speed is
maintained automatically.
IMPORTANTThe Cruise Control
can only be switched on when speed
exceeds 40 km/h in 4
thor 5thgear.
fig. 107
F0B0072b
fig. 108
F0B0224b
Use the speed control
system only when the
traffic or road conditions
make it possible to maintain a
constant speed for quite a long
way safely.

GETTING TO KNOW YOUR CAR
89
Memorisation of a speed: (only in
4thor 5thgear and at speeds above
40 km/h): Move lever Ato ON, the
current speed of the vehicle is main-
tained and memorised and wording
“ON” under the speedometer symbol
will turn on, on the odometer display.
If necessary, the speed set may be in-
creased by pressing the accelerator
pedal (e.g. when overtaking); when the
pedal is released the system will return
the speed of the vehicle to that mem-
orised previously.
Acceleration or deceleration
(using lever only): when the vehicle
is travelling at an automatic regulated
speed, move the lever Bto deceler-
ate or Cto accelerate.
Disengagement of the device:
press button Don the lever edge.
The device will switch itself off au-
tomatically when the brake or clutch
pedal is pressed.Restoring the memorised speed:
after pressing the brake or clutch ped-
al or after the device has been disen-
gaged, press button Dto restore the
last speed memorised.
Memory deletion:turn button
from ON to OFF to clear all the mem-
ories.
IMPORTANTUse the speed con-
trol system only when the traffic or
road conditions make it possible to
maintain a constant speed.MANUAL GEARBOX
To engage the gears, press down the
clutch and put the gear lever into one
of the positions shown in the diagram
on the gear lever knob.
IMPORTANTTo put the vehicle
in reverse, the vehicle must be sta-
tionary. Then with the engine running,
shift into reverse and wait at least
2 seconds with the clutch pedal
pressed fully to avoid scraping and
damaging the gears and back.
fig. 109
F0B0073b

GETTING TO KNOW YOUR CAR
90
To engage the reverse gear (R) from
the neutral position:
– lift the sliding ring A-fig. 111-112
under the knob and move the lever on
the left and then forward.Press the clutch pedal
fully when changing gear.
The floor under the ped-
al must therefore be clear and
any floor mats must lie flat and
not get in the way of the pedals.ELECTRONIC
AUTOMATIC
TRANSMISSION
It has four gears and a reverse which
adapt to the driver’s driving style ac-
cording to the road conditions and the
vehicle load.
IMPORTANTTo use the auto-
matic electronic gear (and the relative
Shift-lock safety device) in the correct
way, read carefully the following in-
structions.
fig. 111
F0B0075b
fig. 112
F0B0302b

GETTING TO KNOW YOUR CAR
91
SELECTION LEVER fig. 113
P= Parking.
R= Reverse.
N= Neutral.
D= Drive, automatic forward gear.M= Sequence mode.
+= Shift to a higher gear in sequence
mode.
–= Shift to a lower gear in sequence
mode.DISPLAY fig. 114
It is possible to view on the display:
– the selected gear (P, R, N, D),
when driving with the automatic gear;
– the selected gear, when driving in
sequence mode, through or .
LEVER POSITION
Drive, automatic gear forward
(D)
Position Dis used on urban and ex-
tra-urban roads.
fig. 113
F0B0252b
fig. 114
F0B0253bShifting the lever from P
to D (P6D), from N to D
(N6D) and from R to D
(R6D) should be made only
when the vehicle is stationary,
the engine idling and the brake
pedal fully pressed (shift - lock
safety device).

GETTING TO KNOW YOUR CAR
92
Neutral (N)
It corresponds to the neutral posi-
tion of a traditional mechanic gear.Reverse (R)
To engage the reverse
the vehicle must be sta-
tionary, the engine idling
and the accelerator pedal re-
leased. Then follow the instruc-
tions given in “Engine starting”
paragraph in this chapter.
When the engine is at Rit is not pos-
sible to start the engine.Parking (P)
Pposition locks drive wheels.
Engage this gear only when the ve-
hicle is stationary and apply also the
handbrake. Then follow the instruc-
tions given in “Engine starting” para-
graph in this chapter.
IMPORTANTIf the lever is not
positioned correctly, the last stable en-
gaged gear flashes on the display. To move the lever from
N, release the accelerator
pedal, let the engine idling
and follow the instructions given
in “Engine starting” paragraph in
this chapter.
When the lever is at N it is possible
to start the engine.

It is dangerous to let the
engine run in a garage or
other closed area. The
engine consumes oxygen and
gives off carbon dioxide, carbon
monoxide and other poisonous
fumes.
– Make sure the handbrake is up and
the gear lever in Por N: the engine
can be started only with the gear in
these two positions.
– Turn the ignition key to Dwithout
pressing the accelerator pedal.
If the engine does not start at the
first attempt, return the ignition key
to Sbefore trying to start the engine
again.
GETTING TO KNOW YOUR CAR
93
STARTING THE ENGINEIf the instrument panel warning light
stays on when the ignition key is at M,
turn the key to Sand then back to M;
if the warning light still remains lit, try
with the other keys provided with the
vehicle.
If you are still unable to start the en-
gine (see “In an emergency” chapter)
contact a Fiat Dealership as soon as
possible.
IMPORTANTDo not leave the ig-
nition key at Mwhen the engine is off
to prevent draining the battery charge.MOVING THE CAR
Proceed as follows:
– press fully the brake pedal;
– select the required gear lever po-
sition;
– accelerate progressively; the vehi-
cle is started and the gear shift de-
pends on the position selected.
When the ignition key is
at M, it is possible to shift
the gear lever from P on-
ly when the brake pedal is fully
depressed (Shift-lock safety de-
vice).

GETTING TO KNOW YOUR CAR
94
SEQUENCE DRIVING MODE
Shift the lever from Dto the right,
into M position:
• if the lever is shifted to +: higher
gear engaged;
• if the lever is shifted to –: lower
gear engaged.
Each gear shift can be viewed on the
display and any mistake is automati-
cally excluded by the control unit
which allows to engage a lower gear
only if the engine revolutions make it
possible.
With sequence driving the automat-
ic electronic gearbox works as a fixed
gearbox controlled in sequence mode.
The electronic control shifts the gear
when the engine revolutions are low-
er than the rpm allowed.AUTOMATIC DRIVING MODE
It is possible to select Din any dri-
ving condition.
The optimal gear shift is selected by
the control unit according to the
speed and the engine load (position of
the accelerator pedal).
When no power is required by the
engine, longer gear shifts are selected
so that consumption is reduced.
When the accelerator pedal is
pressed, more power is required, thus
lower gear shifts are selected and the
car performance is improved in terms
of acceleration and pickup: in this case
consumption raises.For a rapid car pickup:
– press the accelerator pedal fully un-
til the kick-down device is activated so
that maximum performance is reached
(obviously, consumption raises).
IMPORTANTWhen driving on
roads covered in snow, ice, etc. (low
grip) do not activate the kick-down
device.

GETTING TO KNOW YOUR CAR
95
Driving on snow or ice
When driving on snow or ice (low
grip) we recommend to press button
A-fig. 115:
– Symbol òis displayed fig. 116and
the car is started with the second gear.IMPORTANTThis is is possible
only when the lever is at D; if the
lever is shifted from D, it is excluded
automatically. This function can be ac-
tivated also when the car is travelling,
provided that speed in lower than
45 km/h.FAILURE INDICATIONS
The electronic automatic transmis-
sion failure is warned by the display of
a dedicated message on the Connect
infotelematic system screen.
The electronic automatic transmis-
sion failure is warned by the display of
a dedicated message on the in-
fotelematic display and symbol òflash-
ing on the display fig. 116.
Contact as soon as possible the Fi-
at Dealershipto have the failure re-
moved.
fig. 115
F0B0254b
fig. 116
F0B0255b