2007 FIAT IDEA clock

229
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
It is of vital importance to communicate that the tyre has been repaired using the
quick tyre repair kit. Hand the instruction brochure to the personnel charged with
treating the tyre repaired with the kit.WARNING
❒if reaching the tyre pressure specified in paragraph “Inflation pressure”
in section “Technical Specifications”, start driving immediately;
❒after driving for about 10 minutes stop and check again the tyre pres-
sure; pull up the handbrake;
❒if at least 1.8 bar pressure is read, restore proper pressure (with engine
running and handbrake on) and restart;
❒drive with the utmost care to the nearest Fiat Dealership.
FOR CHECKING AND RESTORING PRESSURE ONLY
The compressor can be also used just for restoring pressure. Disconnect
the quick connection and connect it directly to the tyre valve; in this way the
cylinder is not connected to compressor and the sealing fluid will not flow
into the tyre.
CYLINDER REPLACEMENT PROCEDURE
To replace the cylinder proceed as follows:
❒disconnect connection A;
❒turn counter-clockwise the cylinder to replace and raise it;
❒fit the new cylinder and turn it clockwise;
❒connect connection Ato the cylinder and fit the transparent tube Bin-
to the proper space.
F0H0359m
F0H0360m

238
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
IMPORTANT The headlight inner surface may be lightly misted over: this
is not a fault but a natural fact due to low temperature and the level of
air humidity. It will disappear as soon the headlights are turned on. The
presence of drops inside the headlights means water infiltration,
therefore contact Fiat Dealership.
TYPES OF BULBS
Various types of bulbs are fitted to your car:
AGlass bulbs:clipped into position. Pull to remove.
BBayonet type bulbs:press the bulb, turn counterclockwise to
remove this type of bulb from its holder.
CTubular bulbs:free them from their contacts to remove.
D-EHalogen bulbs:to remove the bulb, release the clip holding the
bulb in place.
F0H0178m

241
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
MAIN BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❒turn the cap (A) anticlockwise and remove it;
❒disconnect the electrical connector (B);
❒release the bulb catch (C);
❒remove the bulb (D) and change it;
❒refit the catch (C), connect the electrical connector (B) and fit the cap
(A) turning it clockwise. Put the cap ventilation outlet (H) from the
top downwards.
DIPPED BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❒remove the protective cover releasing the relevant catch;
❒disconnect the electrical connector (F);
❒release the bulb catch (E);
❒remove the bulb (G) and change it;
❒fit a new bulb making the tabs of the metallic part coincide with the
grooves on the reflector, then hook the bulb holder catch (E) and re-
connect the electrical connector (F);
❒refit the protective cover correctly.
F0H0181m
C
B
D
F0H0214m
F0H0182m

242
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
F0H0183m
F0H0184m
DIRECTION INDICATORS
Front
To change the bulb, proceed as follows:
❒remove the protective cover releasing the relevant catch;
❒turn the bulb holder (A) counter-clockwise and remove it;
❒remove the bulb (B) lightly pushing it and turning it counter-clockwise
(“bayonet”);
❒replace the bulb;
❒refit the bulb holder turning it clockwise, checking that it is secured
correctly.
❒refit the protective cover correctly
Side
To change the bulb, proceed as follows:
❒lever in the point shown by the arrow to compress the catch and
remove the unit (C);
❒turn the bulb holder (D) counter-clockwise, remove the snap-fitted
bulb and change it;
❒refit the bulb holder (D) in the transparent cover, then position the
unit making sure the catch clicks into place.

244
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
F0H0187m
F0H0188m
REAR LIGHT UNITS
To change the bulb, proceed as follows:
❒open the tailgate;
❒turn the fastener (A) counter-clockwise (for the left lid) or clockwise
(for the right lid) and remove the cover;
❒disconnect the electrical connector (C);
❒slacken the two fastening nuts (B);
❒to remove the headlight, pull it in perpendicular direction using the
handle on the headlight;
❒press the bulb holder tabs and remove it from its housing;
❒remove bulbs (D) - (E) - (F) - (G) lightly pushing them and turning
them counter-clockwise;
❒refit the bulb holder and make sure the two tabs are fastened and
then connect the electrical connector (C); drive in the two fastening
nuts (B); refit the cover checking that the tabs are fitted in their seat
and turning the fastener (A) counter-clockwise (for the left lid) or
clockwise (for the right lid) to hook it.
In the event of a failure (burnt-out bulbs) on taillights, brake lights will
switch on dimmed automatically in order to guarantee temporary lighting
at the back of the car.
After replacing the burnt-out bulb the taillights will operate regularly.