2007 DODGE SPRINTER key

304 Practical hintsWhere will I find...?
5
Chassis
The wheel chock is on the left-hand side
behind the rear axle.
Example illustration of chassis
\1Pull the retainer springs down and re-
move the chock.If it is no longer possible to close the slid-
ing sunroof, you can close it manually by
operating the drive located behind the trim
at the front of the sliding sunroof.
1Trim
2Cover cap
\1Remove cover cap2 from trim1.3Opening
4Emergency operation key
\1Take emergency operation key 4 from
the vehicle document wallet in the
glove box.
\1Insert emergency operation key 4 into
opening3 of the drive.
\1Open or close the sliding sunroof by
turning it in the appropriate direction.
\1Pull out emergency operation key 4
and place it in the vehicle document
wallet.
\1Clip cover cap2 back on.
!
CAUTION
When storing it away, make sure that
the chock is secured in the retainer by
the retainer springs.
Sliding sunroof*
N77.20-2041-31
N77.20-2040-31

315 Practical hints
Changing the batteries
5
\3 Changing the batteriesIf the remote control batteries (remote
keyless entry) are discharged, you will only
be able to lock and unlock the vehicle man-
ually using the key.
If the batteries in the auxiliary heating re-
mote control are discharged, you will only
be able to switch the auxiliary heating on
or off using the auxiliary heating / heater
booster switch inside the vehicle
(\2page 140).
It is advisable to have the batteries
changed at an authorized Sprinter Dealer.You need two CR 2025 3 V cell batteries or
equivalent.
Do not touch the battery contact surfaces.Warning
G
Keep batteries away from children.
Consult a doctor immediately if a battery is
swallowed.
Dispose of used batteries in an environmen-
tally responsible manner.
Danger of explosion if the battery is not cor-
rectly replaced.
Replacements should always be either of
the same type or one which has been rec-
ommended by the manufacturer.
Environmental note
H
Batteries contain materials that can harm
the environment if disposed of improperly.
Recycling of batteries is the preferred meth-
od of disposal. Many states require sellers
of batteries to accept old batteries for recy-
cling.iAlways replace all the batteries at the
same time. Suitable batteries are avail-
able from an authorized Sprinter Deal-
er. You can also have the batteries
changed there and return used batter-
ies.
Remote control
(remote keyless entry)iWhen inserting the batteries, make
sure that they are clean and lint-free.!
CAUTION
Do not operate the remote control
while the battery is being replaced.

316 Practical hintsChanging the batteries
5
1Battery cover
2Release button for mechaniocal key
\1Release the mechanical key by press-
ing the release button2.
\1Remove the battery cover1.\1Remove the battery and install a new
one (note correct polarity; positive ter-
minal up).
\1Press battery cover1 until it snaps
into place.
\1Check the function of all remote con-
trol buttons on vehicle.You need three Micro / AAA / LR03 batter-
ies or equivalent.
1Battery cover
2Batteries
\1Remove battery cover1 using a suit-
able implement, for example a key, and
put it to one side.
\1Remove old batteries2.
\1Insert three new batteries2. Observe
the plus and minus signs in the remote
control.
\1Slide battery cover1 onto the remote
control as illustrated.
\1
Check the auxiliary heating functions on
the vehicle using the remote control.Auxiliary heating remote control*
N83.00-2062-31

317 Practical hints
Fuel system
5
\3 Fuel systemOn vehicles with a diesel engine, it is nec-
essary to drain the fuel filter if the/ in-
dicator lamp lights up.
To this end, have the fuel filter with water
separator drained at an authorized Sprint-
er Dealer which has the necessary special-
ist knowledge and tools to carry out the
work required.The fuel filter with water separator is in the
engine compartment.
1Drain hose
2Drain plug
\1Apply the handbrake and move the se-
lector lever to positionP.
\1Switch off the engine and open the
hood (\2page 185).
\1Place a suitable container under drain
hose1.
\1Switch on the ignition (\2page 67).\1Unscrew drain plug2 immediately
one turn or until liquid flows out of
drain hose1.
\1Make sure that the liquid flows into the
container under drain hose 1.
\1Close drain plug 2 as soon as approx-
imately 0.2 US qt (0.2 l) of liquid has
been collected.
\1When you have drained the fuel filter
with water separator, turn the key back
to position0 in the ignition lock
(\2page 67).
\1Dispose of the collected liquid in an en-
vironmentally responsible manner.Draining the fuel filter!
CAUTION
Drain the fuel filter with water separa-
tor immediately if the/ indicator
lamp lights up. The engine could be
damaged.
Environmental note
H
When handling, storing and disposing of die-
sel and diesel mixtures, please observe the
relevant regulations.
iThe electric fuel delivery pump stops
the flow of liquid automatically after
30 seconds.

319 Practical hints
Replacing the wiper blades
5
\3 Replacing the wiper blades
\1Apply the handbrake (\2page 115).
1Wiper blade
2Retaining clips
3Wiper arm
\1Fold the wiper arms away from the
windshield.\1Press two retaining clips2 together in
the direction of the arrow and fold wip-
er blade1 away from wiper arm3.
\1Pull wiper blade1 up and out of the
retainer.
\1Slide wiper blade1 into the retainer
on the wiper arm.
\1Press wiper blade1 onto wiper
arm3 until you hear retaining clips2
engage.
\1Fold wiper arm3 onto the windshield
again.
!
CAUTION
Do not open the hood while the wiper
arms are folded away from the wind-
shield. You would damage the hood
and the wiper arms.
Do not fold the wiper arms onto the
windshield without wiper blades being
attached. You could scratch the wind-
shield.
For your own convenience, have this
work carried out at an authorized
Sprinter Dealer.
Removing the wiper bladesWarning
G
When the windshield wipers are set to inter-
mittent wipe or the rain sensor is active, the
windshield wipers could move at any time
and injure yourself or others upon contact
with them.
Always remove the key from the ignition
lock before replacing the wiper blades.
Installing the wiper blades

333 Practical hints
Flat tire
5
\1Then press0 on electric air pump
switch1.
The electric air pump is switched off.
\1Screw the valve cap onto tire valveb.
\1After filling with tire sealant
(\2page 333).
After filling with tire sealant
\1Turn the pressure release screw on
pressure gauge5 counterclockwise
and bleed the system.
\1Turn the key to position0 in the igni-
tion lock (\2page 67).
\1Pull the electric air pump connector out
of the 12 V socket.
\1Store the electric air pump, tire sealant
bottle 8 with valve core extractorc
and, if used, the warning triangle and
hazard warning lamps inside the vehi-
cle.\1Unscrew and remove angle bracket 2
from valve7 on tire sealant bottle 8
and screw the valve cap onto the valve.
\1Pull away immediately.
This enables the tire sealant to distrib-
ute inside the tire and create a more ef-
fective seal.
\1Stop after about 3 minutes and check
the tire pressure using the electric air
pump, for example.\1Correct the tire pressure accordingly if
it does not correspond to the recom-
mended tire pressure (\2page 210).
Increasing the tire pressure
\1Switch on the electric air pump.
Reducing the tire pressure
\1Open the pressure release screw
on pressure gauge 5.
\1Drive to the nearest workshop and
have the tire repaired or replaced.
\1Clean the valve core extractor using
clean water.
\1Have tire sealant bottle8 replaced as
soon as possible at an authorized
Sprinter Dealer.
iThe tire sealant is water soluble. If tire
sealant escapes, you can wash it away
with water.
Warning
G
Do not exceed the maximum speed of
50 mph (80 km/h).
The "max. 50 mph (80 km/h)" sticker must
be affixed within the driver's field of vision.
The vehicle’s handling characteristics may
be affected.iYou must connect the angle bracket on
hose 3 of the electric air pump direct-
ly to the tire valve on the tire.

335 Practical hints
Battery
5
\3 BatteryYour vehicle may be equipped with two
batteries, depending on the equipment
version:
\4Starter battery in the battery recess in
the driver’s footwell
\4Auxiliary battery* in the engine com-
partmentHave the batteries removed at an autho-
rized Sprinter Dealer which has the neces-
sary specialist knowledge and tools to
carry out the work required.
The manufacturer recommends that you
use an authorized Sprinter Dealer for this
purpose.
\1Switch off all electrical consumers.
iThe auxiliary battery* in the engine
compartment is not suitable for jump-
starting operations. Only use the jump-
starting connection in the engine com-
partment if you require jump-starting
assistance or wish to provide jump-
starting assistance (\2page 340).Warning
G
Observe the safety notes in the “Operation”
section (\2page 195).
Do not place any metal objects on the bat-
tery. Doing so can cause a short circuit.
Use only impact-resistant batteries with a
central gas release cover to prevent corro-
sion damage and to protect occupants from
caustic burns in the event of an accident.Disconnecting the batteryWarning
G
There is a risk of a short circuit if the positive
terminal of the connected battery comes
into contact with vehicle parts. The highly
explosive gas mixture could ignite as a re-
sult. You and others could be seriously in-
jured as a result.
\4Do not place any metal objects or tools
on the batteries.
\4When disconnecting the batteries, al-
ways disconnect the negative terminals
first and then the positive terminals.
\4When reconnecting the batteries, al-
ways reconnect the positive terminals
first and then the negative terminals.
\4Do not loosen or disconnect the termi-
nal clamps on the batteries while the en-
gine is running.!
CAUTION
Switch off the engine and take the key
out of the ignition lock before you loos-
en or disconnect the terminal clamps.
You may otherwise destroy electronic
components such as the alternator.
Always disconnect the starter battery
in the battery recess in the driver’s
footwell first.

340 Practical hintsJump-starting
5
\3 Jump-startingIf the starter battery in the battery recess
in the driver’s footwell is discharged, the
engine can be jump-started from another
vehicle using jump leads.
For this purpose, the vehicle is equipped
with a jump-starting connection point.
Please note:
\4Jump-starting must only be performed
when the engine and catalytic convert-
er are cold.\4Do not start the engine if the battery
has frozen. Let the battery thaw out
first.
\4Only use a battery of the same rated
voltage and of approximately the same
capacity for jump-starting.
\4Only use jumper cables of adequate
cross-section with insulated battery
terminal clamps.
\1Make sure that the two vehicles do not
touch.
\1Apply the handbrake or move the se-
lector lever to positionP.
\1Switch off all electrical consumers.
\1Switch on the battery isolating switch*
if necessary (\2page 197).\1Remove the key from the ignition lock.
\1Open the hood (\2page 185).
The jump-starting connection point is on
the left-hand side of the air cleaner in the
engine compartment when looking in the
direction of travel.
Jump-starting connection point1Positive terminal clamp of jumper ca-
ble
\1Remove the positive terminal cover
from the donor battery.
\1Connect positive terminal of donor bat-
tery 2 to jump-starting connection
point 1 with the jumper cable. Start
with the donor battery.
iThe auxiliary battery* in the engine
compartment is not suitable for jump-
starting operations. Only use the jump-
starting connection in the engine com-
partment if you require jump-starting
assistance or wish to provide jump-
starting assistance.!
CAUTION
Avoid repeated and lengthy starting at-
tempts.
Never start the vehicle using a rapid
battery charger.
Warning
G
Avoid creating sparks. Keep naked flames
away from the battery, and do not smoke.
Comply with safety precautions and special
protective measures when handling batter-
ies (\2page 195).
\2\2