2007 Citroen C6 DAG Owner's Manual

I
20
12
3
IN BRIEF
SEAT BELTS WARNING LAMPTYRE DEFLATION DETECTION
This function warns you of tyres that are defl ated or punctured.
Tyre defl ation alert: The SERVICE warning lamp comes on and a vehicle outline is displayed.
“Puncture”: The “STOP” and tyre(s) punctured warning lamps light up, and a vehicle outline is displayed.
Colour screen CNaviDrive colour display
Display of tyres in good condition
Tyre very defl ated
Tyre defl ated
“Puncture”
31- 65
The driver's and the front and rear passengers' seats have sensors that detect non-fastening/unfas-tening of the seat belts.
The fastened/non-fastened status of the seat belts for each type of seat is indicated by the illumination or fl ashing of the warning lamps 1, 2 and 3.
M O N I T O R I N G

II
2121
D
C
E
B
A
IN BRIEF
FRONT PASSENGER'S AIR-BAG DEACTIVATIONCHILD SAFETYTHE ISOFIX FASTENING SYS-TEM
In order to be able to use a rear-facing child seat in the front pas-senger's seat position, it is impera-tive to deactivate the passenger's airbag.
For that:With the ignition switched off, insert the key into the switch A.Turn the key to the “OFF” posi-tion, the passenger's airbag is deactivated.
The front passenger's airbag deac-tivation warning lamp, in the instru-ment panel, lights up when you switch on the ignition.

22
II
W I P E R S
CONTROL POSITIONS2: Rapid wipe.
1: Normal wipe.
I: Intermittent wipe.0: Off.
One press downwards:AUTO:Automatic wipe activated.Single wipe.

23
II
W I P E R S
CHANGING THE WIPER BLADES
If you have to replace them, the wiper blades have to be parked in the maintenance position. For this, switch off the ignition and then within one minute move the wiper control stalk. The wipers stand up in a vertical position.
After replacement, switch on the ignition and move the wiper control stalk so that the wipers resume their normal position.Note: this action places the Piloted Defl ector in the maintenance position. See “Piloted Defl ector”.
WINDSCREEN WASH
To operate the windscreen wash, pull the wiper stalk towards you.
The screen wash is accompanied by a timed wipe of the windscreen , the headlamp wash also activates if the dipped beams are on.
The display of a message indicates that there is only approx. one litre of screen wash fl uid remaining.
In freezing conditions, always check that the wiper blades are free to operate.
Remove any accumulation of snow at the base of the windscreen.

24
II
S I G N A L L I N G
DIRECTION INDICATORS
Left, downwards.
Right, upwards.
For a change of direction, move the control stalk beyond the tight spot. Stops automatically with the return of the steering wheel.
Visible alert / headlamp fl ash
Pull the control towards you.
The headlamp fl ash can be made even with the ignition switched off.
Horn
Press at the centre of the steering wheel.
HAZARD WARNING LAMPS
This operates all the direction indi-cators simultaneously.
Only use them to indicate dan-ger, for an emergency stop or for driving in abnormal conditions.
The hazard lamps can also be used with the ignition switched off.
SOUND SIGNAL FOR HEAD-LAMPS LEFT ON
This operates when the driver's door is opened, ignition off, to indi-cate that the vehicle lamps are still on.
It stops when you close the door, switch off the lamps or switch on the ignition.
This signal does not operate if the automatic lighting of headlamps or the guide-me-home lighting are active.
EMERGENCY OPERATION OF HAZARD WARNING LAMPS
A sudden deceleration of the vehi-cle causes the hazard lamps to come on automatically.
They will cease to operate auto-matically, or manually if you press the hazard lamps button on the dashboard.
The direction indicators cannot operate if the hazard warning lamps are on.

25
II
41/58/61
A
S I G N A L L I N G
LIGHTING CONTROL STALK
All vehicle lamps off
Sidelamps on
Dipped beams/main beams on
Dipped beams/main beams dipswitch
Rotate the ring A forwards.
Rotate the ring A forwards.
AUTOMATIC LIGHTING OF HEADLAMPS
Sidelamps and dipped beams come on automatically in poor ambient light, or if the wipers are in continuous operation. They go out as soon as the ambient light again become suffi cient or when the wipers cea se to operate.
Activation/deactivation of this function is possible in the menu “Personalisa-tion/Confi guration” in the “Main menu”.Note: Activation of this function is immediate while deactivation re quires the ignition to be switched off.
Take care not to cover the brightness sensor, which is visible from out-side the windscreen, behind the interior rear view mirror.
GUIDE-ME-HOME LIGHTING
This function switches on your headlamps, to light your way when you wish to walk from a carpark, for example.
This function is activated:Manually by pulling the con-trol A towards you, with the ignition switched off.Automatically, provided:
The automatic lighting of headlamps is activated.To activate the guide-me-home lighting function, select in the “Main menu”, then in “Personalisation/Configura-tion”, the sub-menu for light-ing and signalling, then acti-vate the function.
See “Multifunction display”.Note: It is possible to modify the duration of the guide-me-home lighting (approx. 60, 30 or 15 sec-onds) in the menu “Personalisa-tion/Confi guration”.

26
II
C
S I G N A L L I N G
Front foglamps on
Front foglamps and rear foglamps on
Rotate the ring C forwards.
Switching off
First action rearwards, rear foglamps off.
Second action rearwards, front and rear foglamps off.Note: the foglamps should be used only in fog or in other conditions of poor visibility.
FRONT AND REAR FOGLAMPS (RING C)
Lighting
With dipped/main beams on:
Rotate the ring C forwards.
DAYTIME-RUNNING LAMPS
These come on automatically when the engine is running:If the function is activated in the IfMain Menu. See “Multifunction display”.
Provided the lighting control stalk is on position 0 and all the headlamps are off.
If the daytime-running lamps are active, the sidelamps will also be on (depending on country specifi -cation).

27
II
S T E E R I N G C O L U M N A D J U S T M E N T – S E A T
B E L T H E I G H T A D J U S T M E N T
MANUAL ADJUSTMENT OF THE STEERING WHEEL FOR HEIGHT AND REACH
While the vehicle is stationary, unlock the steering wheel by push-ing the lever forward.
Adjust the height and the reach of the steering wheel, then lock the position by pulling the lever upwards.
ELECTRICAL ADJUSTMENT OF THE STEERING WHEEL FOR HEIGHT OR REACH
While the vehicle is stationary, adjust the height or the reach of the steering wheel by moving the control:forward or rearward to adjust the reachup or down to adjust the height.
The steering wheel adjustment is memorised with the driving posi-tion (See “Memorisation”).