2007 CHEVROLET KODIAK Owners Manual

If the light comes on, use this chart to determine
what action to take.
Water In Fuel Light
Problem Recommended Action
Light comes on
intermittently.Drain water from the
fuel filter.
Light stays on at
temperatures above
freezing.Drain the fuel filter
immediately. If no water
can be drained and the
light stays on, see your
dealer for assistance.
Light stays on at
temperatures below
freezing.Drain the fuel filter
immediately. If no water
can be drained, water
may be frozen in the
water drain system, or in
the fuel lines. Move the
vehicle to a warm location
to thaw out, and then
drain the filter system.
Light stays on
immediately after
refueling, and a large
amount of water was
possibly pumped into the
fuel tank.Fuel tank purging is
required. See your dealer
for assistance.
Notice:If you drive when this warning
indicator is on, you can damage your fuel
injection system and your engine. If the
indicator comes on right after you refuel, it
means water was pumped into your fuel tank.
Turn off your engine immediately. Then,
have the water drained at once.
To drain water, do the following:
1. Stop and park the vehicle in a safe place. Turn
off the engine and apply the parking brake.
2. Remove the fuel cap.
3. Place a fuel-resistant container under the fuel
filter. The filter drain valve is located on the
bottom of the fuel filter.
If your vehicle has the 6.6L engine, the fuel
filter is located in the engine compartment on
the driver’s side of the vehicle. If your
vehicle has either the 7.2L or 7.8L engine, the
fuel filters are located in the engine
compartment on the driver’s side of the
vehicle, and on the driver’s side frame rail in
front of the fuel tank.
257

4. Open the drain
valve by turning
two to three turns.
When fuel empties
from the valve,
all the water
has been drained.
Close the valve
hand-tight.
5. Remove the fuel-resistant container and
properly dispose of the contaminated fuel.
To find out how to properly dispose of
contaminated diesel fuel, seeEngine Oil
(Caterpillar
®Diesel Engine) on page 268or
Engine Oil (Gasoline Engine) on page 268or
Engine Oil (DURAMAX
®/Isuzu Diesel
Engine) on page 272.6. Install the fuel cap.
7. Start the engine and let it run for a few
minutes. If the engine stalls, the fuel system
may need to be primed. While draining
the water from the fuel filter, air may enter the
fuel system. If air has entered the fuel
system the fuel system will need to be primed.
If the water-in-fuel light comes on again after
driving a short distance or the engine runs rough
or stalls, a large amount of water has probably
been pumped into the fuel tank. The fuel
tank should be purged.
Fuel Priming
If your vehicle has a Caterpillar®diesel engine,
see the Caterpillar®Diesel Engine Operation and
Maintenance Manual provided with your vehicle.
If your vehicle has a DURAMAX
®/Isuzu diesel
engine, in order for the fuel system to work
properly, the fuel lines must be full of fuel and
contain no air. If air gets into the fuel lines, it will
be necessary to prime the fuel lines to eliminate air
before operating the vehicle.
258

Air can get into the fuel lines if any of the following
happen:
•The vehicle runs out of fuel.
•The fuel filter is removed for servicing or
replacement.
•The fuel lines are removed or disconnected
for servicing.
•The fuel filter water drain valve is opened
while the engine is running.
If one or more of the above occurred, it is very
likely that air has entered your fuel system and that
you will need to prime the fuel system before
operating the vehicle.
Air in the fuel lines will not harm the engine or the
vehicle. However, the engine may not be able
to start until the fuel system is primed and the air
is removed.
Priming the 6.6L DURAMAX®Diesel
Engine
If your vehicle is equipped with the 6.6L
DURAMAX®diesel engine, it has a priming pump
which is part of the engine mounted fuel filter.
The vent valve and the fuel filter primer pump are
located on top of the fuel filter housing. The
priming pump is hand operated and is designed to
bring fuel to the engine to eliminate any air that
may be in the fuel lines.
To prime the 6.6L DURAMAX
®diesel engine, do
the following:
1. Make sure there is fuel in the tank.
2. Make sure the fuel filter had been installed
and properly tightened.
3. Make sure the fuel lines are properly
connected and the fuel filter is cool enough
to touch.
4. Remove any dirt from the fuel filter head and
vent valve by wiping with a cloth.
259

5. Open the fuel filter
vent valve by turning
the screw
counterclockwise
several full turns.
6. Repeatedly push
down on the fuel
filter primer
pump with the palm
of your hand. Let
the pump return
upward between
pushes.7. Operate the priming pump until a small
amount of fuel seeps from the vent valve.
When you see the fuel, the filter is now full of
fuel and the system should be primed.
8. Close the vent valve.
9. Clean any fuel which accumulated on the fuel
filter.
10. Start the engine and let it idle for a few
minutes.
11. Check the filter for leaks.
260

Priming the 7.8L Isuzu 6H Diesel Engine
If your vehicle is equipped with the 7.8L Isuzu 6H
diesel engine, use the following procedure to
prime the engine:
1. Make sure there is fuel in the fuel tank.
2. Make sure the specified fuel filter is properly
installed.
3. Make sure the fuel lines are securely
connected.
4. Make sure the fuel filter is cool to the touch.
5. Use a clean cloth to remove dirt and oil
from the fuel filter head and breather valve.6. Use the palm of your hand to repeatedly
press and release the plunger (1) at the
top of the fuel filter priming pump. Continue
until the plunger resistance becomes firm. This
may take from 20 to 100 times, depending
upon fuel tank location.
7. Turn the fuel filter breather valve screw (2)
counterclockwise several turns to open the
breather valve.
8. Use the palm of your hand to repeatedly
press and release the plunger (1) at the
top of the fuel filter priming pump until fuel
begins to seep from the breather valve.
9. Tighten the fuel filter breather screw (2) to the
specified torque, 4.9
Y(43 in. lbs).
10. Use the palm of your hand to press and
release the plunger (1) at the top of the
fuel filter priming pump about 20 more times.
This sends fuel to the engine.
11. Use a clean cloth to remove any fuel from the
fuel filter and surrounding area.
12. Start the engine and allow it to idle for a
few minutes.
13. Check the fuel filter for leakage.
261

Running Out of Fuel
If the diesel engine stalls and you think that you
have run out of fuel, do this to restart your engine:
{CAUTION:
Diesel fuel is ammable. It could start a
re if it gets on hot engine parts. You
could be burned. Do not let too much fuel
ow from the air bleed valve, and wipe up
any spilled fuel with a cloth.
1. If you are parked on a level surface, add at
least 2 gallons (7.6 liters) of fuel. However, if
you are parked on a slope, you may need
to add up to 5 gallons (18.9 liters) of fuel.
2. Follow the fuel priming procedure earlier in
this section to prime the fuel filter.3. Close the air bleed valve.
4. Turn the ignition key to START for 10 to
15 seconds at a time until your engine
starts. If the engine tries to run, but does not
run smoothly, increase the rpm a little
using the accelerator pedal. This will help
force air through the system.
Your check engine light may come on if the
vehicle has run out of fuel. This light may stay on
for a few drive cycles after the condition is
corrected, but will eventually clear itself.
262

Fuel Filter Replacement
If you want to change the diesel engine fuel filter
yourself, here is how to do it:
{CAUTION:
Diesel fuel is ammable. It could start a
re if something ignites it, and you could
be burned. Do not let it get on hot engine
parts, and keep matches or other ignition
sources away.
First, drain any water from the filter by following
the water draining procedure earlier in this section.
Your vehicle’s engine should be off until the end
of this procedure.
If your vehicle has the 6.6L engine, the fuel filter is
located in the engine compartment on the
driver’s side of the vehicle. If your vehicle has
either the 7.2L or 7.8L engine, the fuel filters are
located in the engine compartment on the
driver’s side of the vehicle, and on the driver’s
side frame rail in front of the fuel tank.
1. Apply the parking brake.2. Unplug the water
sensor wire
connected to the fuel
filter and unscrew
the filter element.
3. Remove the filter element. If there is any dirt
on the filter sealing surface, clean it off.
Remove and reuse the water sensor float
switch located on the bottom of the fuel filter.
4. Install the new filter element.
5. Reinstall and tighten the filter container and
reconnect the water sensor wire to the filter.
6. Use the fuel filter priming procedure earlier in
this section to prime the fuel filter.
7. Tighten the air bleed valve by turning it
clockwise until hand-tight.
8. Start your engine and let it idle for
five minutes. Check your fuel filter and air
bleed valve for leaks.
263

Fuels in Foreign Countries
If you plan on driving in another country outside the
United States or Canada, the proper fuel may be
hard to find. Never use leaded gasoline or any other
fuel not recommended in the previous text on fuel.
Costly repairs caused by use of improper fuel would
not be covered by your warranty.
To check the fuel availability, ask an auto club, or
contact a major oil company that does business
in the country where you will be driving.
Filling the Tank
{CAUTION:
Fuel vapor is highly ammable. It burns
violently, and that can cause very bad
injuries. Do not smoke if you are near
fuel or refueling your vehicle. Keep
sparks, ames and smoking materials
away from fuel.
The fuel cap can be on either or both sides of
your vehicle depending on option content.
To take off the cap, turn it slowly counterclockwise.
Fuel caps for all
gasoline applications,
and all diesel between
frame rail fuel tank
applicationsFuel caps for all side
mounted diesel
applications
264