2007 CADILLAC CTS V Owners Manual

Each new wheel should have the same
load-carrying capacity, diameter, width, offset and
be mounted the same way as the one it replaces.
If you need to replace any of your wheels,
wheel bolts, or wheel nuts, replace them only with
new GM original equipment parts. This way,
you will be sure to have the right wheel, wheel
bolts, and wheel nuts for your vehicle.
{CAUTION:
Using the wrong replacement wheels,
wheel bolts, or wheel nuts on your vehicle
can be dangerous. It could affect the
braking and handling of your vehicle,
make your tires lose air and make you
lose control. You could have a collision in
which you or others could be injured.
Always use the correct wheel, wheel bolts,
and wheel nuts for replacement.Notice:The wrong wheel can also cause
problems with bearing life, brake cooling,
speedometer or odometer calibration,
headlamp aim, bumper height, vehicle ground
clearance, and tire or tire chain clearance
to the body and chassis.
SeeChanging a Flat Tire (CTS Only) on page 424
for more information.
Used Replacement Wheels
{CAUTION:
Putting a used wheel on your vehicle is
dangerous. You cannot know how it has
been used or how far it has been driven.
It could fail suddenly and cause a crash.
If you have to replace a wheel, use a new
GM original equipment wheel.
417

Tire Chains
{CAUTION:
Do not use tire chains. There is not
enough clearance. Tire chains used on a
vehicle without the proper amount of
clearance can cause damage to the
brakes, suspension, or other vehicle
parts. The area damaged by the tire
chains could cause you to lose control of
your vehicle and you or others may be
injured in a crash. Use another type of
traction device only if its manufacturer
recommends it for use on your vehicle
and tire size combination and road
conditions. Follow that manufacturer’s
instructions. To help avoid damage to
your vehicle, drive slowly, re-adjust or
remove the device if it is contacting your
vehicle, and do not spin your wheels.
If you do nd traction devices that will t,
install them on the rear tires.
Lifting Your Vehicle (CTS-V)
{CAUTION:
Lifting a vehicle can cause an injury.
The vehicle can slip off the jack and roll
over you or other people. You and they
could be badly injured. Find a level place
to lift your vehicle. To help prevent the
vehicle from moving:
1. Place the shift lever in REVERSE (R)
and rmly apply the parking brake.
2. Turn off the engine.
To be even more certain the vehicle will
not move, you can put blocks in front of
and behind the wheels. Also seeParking
Your Vehicle (Manual Transmission) on
page 132andParking Brake on page 128
for additional information.
418

{CAUTION:
Getting under a vehicle when it is jacked
up is dangerous. If the vehicle slips off
the jack, you could be badly injured or
killed. Never get under a vehicle when it is
supported only by a jack.
{CAUTION:
Raising your vehicle with the jack
improperly positioned can damage the
vehicle and even make the vehicle fall. To
help avoid personal injury and vehicle
damage, be sure to place the jack in the
proper location before raising the vehicle.
If you ever use a jack to lift your vehicle, follow
the instructions that came with the jack, and
be sure to use the correct lifting points to avoid
damaging your vehicle.Notice:Lifting your vehicle improperly can
damage your vehicle and result in costly repairs
not covered by your warranty. To lift your
vehicle properly, follow the advice in this part.
To help prevent vehicle damage:
Be sure the jack you are using meets the
weight standards for your vehicle and is
in good working order.
Be sure to place a block or pad between
the jack and the vehicle.
Make sure the jack you are using only
contacts the jacking location lift points and
is not leaning on any other vehicle
components such as the rocker panels, the
oor pan, or the stone guard moldings.
Lift only in the areas shown in the following
pictures.
419

Lifting From the Front
The front lifting points can be accessed from
either side of your vehicle, behind the front tires.1. Locate the front lifting points using the
diagram shown above and corresponding
triangular-shaped hoisting notches located in
the plastic molding. The front lifting location
is about 14 inches (35.6 cm) from the
rear edge of the front wheel well.
2. Be sure to place a block or pad between the
jack and the vehicle.
3. Lift the vehicle with the jack, making sure the
jack is centered on the front lifting point.
420

Lifting From the Rear
The rear lifting points can be accessed from either
side of your vehicle, in front of the rear tires.1. Locate the rear lifting points using the
diagram shown above and corresponding
triangular-shaped hoisting notches located in
the plastic molding. The rear lifting location
is about 7 inches (17.8 cm) from the
front edge of the rear wheel well.
2. Be sure to place a block or pad between the
jack and the vehicle.
3. Lift the vehicle with the jack, making sure the
jack is centered on the rear lifting point.
SeeDoing Your Own Service Work on page 333
for additional information.
421

If a Tire Goes Flat
It is unusual for a tire to “blowout” while you are
driving, especially if you maintain your tires
properly. SeeTires on page 392. If air goes out of a
tire, it is much more likely to leak out slowly. But if
you should ever have a “blowout”, here are a few
tips about what to expect and what to do:
If a front tire fails, the at tire will create a drag
that pulls the vehicle toward that side. Take your
foot off the accelerator pedal and grip the
steering wheel rmly. Steer to maintain lane
position, and then gently brake to a stop well out
of the traffic lane.
A rear blowout, particularly on a curve, acts much
like a skid and may require the same correction
you’d use in a skid. In any rear blowout, remove
your foot from the accelerator pedal. Get the
vehicle under control by steering the way you want
the vehicle to go. It may be very bumpy and
noisy, but you can still steer. Gently brake to a
stop — well off the road if possible.If a tire goes at, and your vehicle has a spare
tire, seeChanging a Flat Tire (CTS Only) on
page 424. This information shows you how to use
your vehicle’s tire changing equipment and
how to change a at tire safely.
{CAUTION:
Lifting a vehicle and getting under it to do
maintenance or repairs is dangerous
without the appropriate safety equipment
and training. The jack provided with your
vehicle is designed only for changing a
at tire. If it is used for anything else, you
or others could be badly injured or killed
if the vehicle slips off the jack. Use the
jack provided with your vehicle only for
changing a at tire.
422

Run-Flat Tires (CTS-V)
If your vehicle has run-at tires, there is no spare
tire and no tire changing equipment. Run-at
tires can operate effectively with no air pressure
for a limited distance and speed. Your vehicle also
has a Tire Pressure Monitor (TPM) which will
alert you if there is a loss of tire pressure in any of
the tires. These tires perform so well without
any air pressure that a Tire Pressure Monitor
(TPM) is used to alert you when there is a low tire
condition.
{CAUTION:
When the low tire warning light is
displayed on the instrument panel cluster,
your vehicle’s handling capabilities will
be reduced during severe maneuvers.
If you drive too fast, you could lose control
of your vehicle. You or others could be
injured. Do not drive over 55 mph (90 km/h)
CAUTION: (Continued)
CAUTION: (Continued)
when the low tire warning light is
displayed. Drive cautiously and check
your tire pressures as soon as you can.
SeeRun-Flat Tires (CTS-V) on page 400and
Tire Pressure Monitor System on page 405,
for additional information.
{CAUTION:
Special tools and procedures are required
to service a run-at tire. If these special
tools and procedures are not used you or
others could be injured and your vehicle
could be damaged. Always be sure the
proper tools and procedures, as described
in the service manual, are used.
To order a service manual seeService
Publications Ordering Information on page 501.
423

Changing a Flat Tire (CTS Only)
If a tire goes at, avoid further tire and wheel
damage by driving slowly to a level place. Turn on
your hazard warning ashers.
{CAUTION:
Changing a tire can be dangerous. The
vehicle can slip off the jack and roll over
or fall on you or other people. You and
they could be badly injured or even killed.
Find a level place to change your tire.
To help prevent the vehicle from moving:
1. Set the parking brake rmly.
2. Put an automatic transmission shift
lever in PARK (P), or shift a manual
transmission to FIRST (1) or
REVERSE (R).
3. Turn off the engine and do not restart
while the vehicle is raised.
4. Do not allow passengers to remain in
the vehicle.
CAUTION: (Continued)
CAUTION: (Continued)
Put the wheel blocks at the front and rear of
the tire farthest away from the one being
changed. That would be the tire on the other
side, at the opposite end of the vehicle.
When you have a at tire, use the following
example as a guide to assist you in the placement
of wheel blocks.
The following information will tell you next how to
use the jack and change a tire.
424