ably an authorised BMW Mo-
torrad dealer.
Install the oil dipstick.
Install the front seat ( 75)Topping up engine oilPour engine oil in through filler
neck1until it reaches the spe-
cified level.
Check the engine oil level
( 107)
Brake system, generalReliabilityA fully functional brake system is
a basic requirement for the road
safety of your motorcycle.
Do not ride the motorcycle if you
have any doubts about the de-
pendability of the brake system.
Under these circumstances have
the brake system checked by a
specialist workshop, preferably
an authorised BMW Motorrad
dealer.
Incorrect working practices
endanger the reliability of
the brakes.
Have all work on the brake sys-
tem performed by a specialist
workshop, preferably an author-
ised BMW Motorrad dealer.Checking operation of
brakesPull the handbrake lever. The pressure point must be
clearly perceptible.
Press the footbrake lever.
The pressure point must be
clearly perceptible.
Brake padsChecking front brake pad
thickness
Brake pads worn past
the minimum permissible
brake-pad thickness can cause
a reduction in braking efficiency
and under certain circumstances
they can cause damage to the
brake system.
In order to ensure the dependab-
ility of the brake system, do not
permit the brake pads to wear
past the minimum permissible
brake-pad thickness.
Make sure the ground is level
and firm and place the motor-
cycle on its stand.
8109zMaintenance
Remove stains of this kind im-
mediately, using cleaning-grade
benzene or petroleum spirit on a
clean cloth or ball of cotton wool.
BMW Motorrad recommends
BMW tar remover for removing
specks of tar. Remember to wax
the parts treated in this way.Protective wax coatingBMW Motorrad recommends
applying only BMW car wax or
products containing carnauba
wax or synthetic wax.
It is time to rewax the paint-
work when water "puddles" on
the surface, instead of forming
beads.Laying up the
motorcycleClean the motorcycle.
Remove the battery.
Spray the brake and clutch
lever pivots and the main andside stand pivots with a suit-
able lubricant.
Coat bright metal and chrome-
plated parts with an acid-free
grease (e.g. Vaseline).
Stand the motorcycle in a dry
room in such a way that there
is no load on either wheel.
Before laying the vehicle
up out of use, have the en-
gine oil and the oil filter element
changed by a specialist work-
shop, preferably an authorised
BMW Motorrad dealer. Com-
bine work for laying up/restoring
to use with a BMW service or
inspection.
Restoring motorcycle
to useRemove the protective wax
coating.
Clean the motorcycle.
Install a charged battery. Before starting: work through
the checklist.
9140zCare
I
IgnitionSwitching off, 47
Switching on, 47
Immobiliser, 48 Warning, 27
Instrument cluster Overview, 18
Sensor for lighting, 18
J
Jump starting, 131
K
Keys, 47
L
Laying up, 140
Lights Headlight flasher, 56
High-beam headlight, 56
Low-beam headlight, 56
Parking light, 56
Side light, 55
Luggage Correct loading, 99 M
Maintenance
General instructions, 106
Mirrors Adjusting, 68
Motorcycle Restoring to use, 140
Multifunction display, 18 Adjust the dimmer, 51
Overview, 22
O
Odometer and tripmeters Resetting, 50
Selecting readings, 49
On-board computer, 17 Ambient temperature, 52
Average consumption, 53
Average speed, 53
Oil level, 54
Range, 52
Reset the average
consumption, 53
Resetting average speed, 53 Selecting readings, 51
Warnings, 30
P
Parking, 85
Power socket, 11, 98
Pre-ride check, 81
R
Rear-wheel drive Technical data, 148
Refuelling, 87 Filler neck, 13
Reserve Warning, 27
Residual range, 50
Restoring to use, 140
Rev. counter, 18
Rider's Manual, 15
Running gear Technical data, 148
Running in, 83
S
Safety instructions, 77
12167zIndex
