2007 Acura TSX battery

The instrument panel has many
indicators to give you important
info rmation about your vehicl e.
This indicator comes on when you
turn the ignition switch to the ON
(II) position. It reminds you and your
passengers to fasten your seat belts.
A beeper also sounds if you and your
front passenger have not fastened
your seat belts.
If you turn the ignition switch to the
ON (II) position before fastening
your seat belts, the beeper sounds,
and the indicator flashes. If you do
not fasten your seat belts before the
beep er stops, the indicator stops
flashing but remains on. If
your front passenger does not
fasten their seat belt, the indicator
comes on about 6 seconds after the
ignition switch is turned to the ON
(II) position.
If either of you do not fasten your
seat belt while driving, the beeper
will sound and the indicator will flash
again at regular intervals. For more
info rmation, see page . The
engine can be severely damaged
if this indicator flashes or stays on
when the engine is running. For
more information, see page .
If this indicator comes on when the
engine is running, the battery is not
being charged, and you will also see
a ‘‘CHECK CHARGING SYSTEM’’
message on the multi-information
display (see page ). For more
info rmation, see page .
You
will also see a ‘‘FASTEN SEAT
BELT’’ or ‘‘FASTEN PASSENGER
SEAT BELT’’ message on the multi-
information display (see page ).You
will also see a ‘‘CHECK
ENGINE OIL LEVEL’’ message on
the multi-information display (see
page ).
You will also see a ‘‘CHECK
EMISSION SYSTEM’’ message on
the multi-information display (see
page ). For more information, see
page . 78
19 331
82
84332
84 332
Instrument Panel Indicators
L ow Oil Pressure
Indicator
Seat Belt Reminder
Indicator
Malf unction Indicator
LampCharging System
Indicator
62

If you see ‘‘CHECK CHARGING
SYSTEM’’ on the multi-information
display, it means the battery is not
being charged. See page for
more information. If
you see ‘‘CHECK EMISSION
SYSTEM’’ on the multi-information
display, it means one of the engine’s
emission systems may have a
problem. Have your vehicle checked
by your dealer (see page ). If
there is a problem with the brake
system, you will see ‘‘CHECK
BRAKE SYSTEM’’ on the multi-
info rmation display. The parking
brake and brake system indicator in
the instrument panel will also come
on. See page f or more
inf ormation. 334
332
332
Check Charging Syst em
Check Emission Syst em Check Brake Syst em
Multi-Inf ormation Display
84
U.S.Canada

Avoid dropping or thro wing the
transmitter.
Protect the transmitter from
extreme temperature.
Do not immerse the transmitter in
any liquid.
If you lose a transmitter, the
replacement needs to be
reprogrammed by your dealer.
To turn it back on, repeat this
procedure. The LED will come on
for 1 second to indicate the feature
has been turned on.
The
driving position memory
activated (Driver 1, Driver 2) is
shownonthebackofeach
transmitter. Make sure you store
your desired driving position in the
memory that is activated by the
transmitter you normally carry.
You can turn off this system
activation. Press and hold the LOCK
and UNLOCK buttons at the same
time. The LED in the remote
transmitter will blink twice. Then
release the buttons. Doing this also
cancels the ‘‘MEMORY POSITION
LI NK’’ setting for that remote and
restores the default settings.
Any
of these actions will stop the
system’s automatic seat adjustment:
Pressing either memory button or
the MEMO button on the driver’s
door.
Pressing any of the seat
adjustment switches.
Shifting out of Park (A/T), or into
reverse (M/T).
When
you open the driver’s door
after unlocking it with the remote
transmitter, you will hear a beep
(depending on the ‘‘KEYLESS
LOCK ACKNOWLEDGEMENT’’
setting see page ). The driver’s
seat will move to the positions stored
inthememorylocation
corresponding with the remote in
use. You will hear two beeps when
the seat stops moving.
If it takes several pushes on the
button to lock or unlock the doors,
replace the battery as soon as
possible.
Battery type: CR2025
113
CONT INUED
Remote Transmitter Care
Replacing the Transmitter Battery
Remote Transmitter
Inst rument s and Cont rols
133

µ
To replace the battery:
Place a cloth on the edge of the
transmitter, and remove the upper
half by caref ully prying on the
edge with a small f lat-tip
screwdriver. Remove the old battery and note
the polarity. Make sure the
polarity of the new battery is the
same ( side f acing up), then
insert it in the transmitter.
Snapthetwohalvesof the
transmitter case back together. An improperly disposed of battery
can hurt the environment.
Always conf irm local regulations
for battery disposal.
1.
2.
3.
As required by the FCC:
This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
Remote Transmitter
134
BATTERY

In the HI setting, the heater turns off
when the seat gets warm, and turns
back on after the seat’s temperature
drops.
In the LO setting, the heater runs
continuously. It does not cycle with
temperature changes.
Follow these precautions whenever
you use the seat heaters:If the engine is lef t idling f or an
extended period, do not use the
seat heaters even on the LO
setting. It can weaken the battery,
causing hard starting. Use the HI setting only to heat the
seats quickly, because it draws
large amounts of current f rom the
battery.
Both f ront seats are equipped with
seat heaters. The passenger seat is
only heated in the seat bottom
because of the side airbag of f system. The ignition switch must be in the
ON (II) position to use them. Push
the front of the switch, HI, to rapidly
heat up the seat. After the seat
reaches a comf ortable temperature,
select LO by pushing the back of the
switch. This will keep the seat warm.
Seat Heaters
Inst rument s and Cont rols
137
SEAT HEATER SWITCHES
Passenger’s
Seat
Driver’s
Seat
HEATERS

CONT INUED
To select a memorized position, do
this:Make sure the parking brake is set
(M/T) or the shif t lever is in Park
(A/T).
Press the desired memory button
(1 or 2) until you hear a beep.
Doing any of the f ollowing af ter
pressing the MEMO button will
cancel the storing procedure.
Not pressing a memory button
within 5 seconds.
Readjusting the seat position.
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory. If
you want to add a new position while
retaining the current one, use the
other memory button.
All stored driving positions will be
lost if your vehicle’s battery goes
dead or is disconnected. Pressing the MEMO button again
within 5 seconds.
Press and release the MEMO
button on the driver’s door. You
will hear a beep. Then, both
indicators in the memory buttons
will start to blink. Press and hold
one of the memory buttons (1 or
2) within 5 seconds af ter you press
the MEMO button. When the
system completes storing a new
driving position, you hear two
beeps. The indicator in the stored
memory button will come on. 1.
2.
3.
Driving Position Memory System
Selecting a Memorized Position
Inst rument s and Cont rols
143
MEMORY BUTTONS
MEMORY BUTTONS MEMO BUTTON
INDICATORS

µIf the driver’s
window senses any obstacle while it
is closing automatically, it will
reverse direction, and then stop. To
close the window, remove the
obstacle, then use the window switch
again.
Auto reverse stops sensing when the
window is almost closed. You should
always check that all passengers and
objects are away from the window
bef ore closing it. If your vehicle’s battery is
disconnected or goes dead, or the
driver’s window f use is removed, the
AUTO f unction may be disabled. If
the AUTO f unction is disabled, the
power window system will need to be
reset af ter reconnecting the battery
or installing the f use.
The power window system has a key-
of f delay f unction. The windows will
still operate f or up to 10 minutes
after you turn off the ignition switch.
Opening either f ront door cancels
the delay function. You must turn
the ignition switch to the ON (II)
position again bef ore you can raise
or lower the windows.
If the power windows do not operate
properly af ter resetting, have your
vehicle checked by your dealer. Pull and hold the driver’s window
switch to close the window
completely, then hold the switch
f or about 2 seconds. Start the engine. Push down and
hold the driver’s window switch
until the window is f ully open.
1.
2.
AUTO REVERSE
Power Windows
148

µ
µ
µ
CONT INUED
The preset f requencies may be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed. Repeat steps 1 through 3 to store a
total of six stations on AM and
twelve stations on FM. Pick the preset number (1 6)
you want for that station. Press
the button or icon and hold it until
you hear a beep.
Each preset button or icon
can store one f requency on AM, and
two f requencies on FM.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each preset
button or icon.
To use the SCAN, preset and A.SEL
f unction, press the AUDIO DISPLAY
button to view these icons.
The SCAN f unction
samples all stations with strong
signals on the selected band. To
activate it, press the SCAN button, or
touch the SCAN icon (models with
navigation system), then release it.
You will see SCAN in the display.
The system will scan f or a station
with a strong signal. When it f inds
one, it will stop and play that station
f or about 5 seconds.
If you do nothing, the system will
then scan f or the next strong station
andplayitfor5seconds.Whenit
plays a station you want to listen to,
press the SCAN button or touch the
SCAN icon again. UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station.
3.
4.
1.
2.
On vehicles with navigation system
Playing the AM/FM Radio
Preset
SCAN
Features
173