2007 Acura TSX Owner's Manual

The multi-inf ormation display
consists of two segments; an upper
segment and a lower segment.
In normal display mode, the upper
segment displays trip computer. The
lower segment displays the
odometer, Trip A/B, outside
temperature, and engine oil lif e and
maintenance message.
Multi-Inf ormation Display
70
SECONDARY DISPLAYLOWER SEGMENT
PRIMARY DISPLAY
UPPER SEGMENT
: Press SEL/RESET Button.
: Press INFO Button.
U.S. model is shown

RANGE: The estimated distance
you can travel on the fuel
remaining in the tank. This
distance is estimated from the fuel
economy you received over the
last several miles, so it will vary
with changes in speed, traffic, etc.
ELAPSED TIME: The time
trave led since you last reset the
trip computer.
AVG. SPEED: The average speed
you are traveling.
TIRE PRESSURE MONITOR:
You can see the pressure of each
tire in this monitor. If the tire
pressu re is low on one or more
tires, inflate them to the correct
pressure. For more information,
see page .
The
primary display always shows its
default setting, ‘‘INST. MPG’’ (U.S.
models) or ‘‘INST. L/100 km’’
(Canadian models) even if you press
the INFO button. It only changes the
secondary display. You can
customize this setting to your liking
(see page ).
The upper segment is divided into
two displays; primary and secondary.
After you turn the ignition switch to
the ON (II) position, press the INFO
button on the steering wheel or the
IN FO knob in the instrument panel.
What you last selected appears on
the secondary display of the trip
computer. Pressing the INFO
button/knob repeatedly changes the
display as shown in the example on
the previous page. Messages in the trip computer
include:
When you turn the ignition switch
to the ON (II) position, ELAPSED
TIME is reset.
INST.MPG(U.S.models)/
INST.L/100 km (Canadian
models): Your vehicle’s current
f uel mileage.
AVG. FUEL A/AVG. FUEL B:
Your vehicle’s average fuel
economy since you last reset the
Trip A or Trip B. When you select
Trip B in the lower segment by
pressing the SEL/RESET button
on the steering wheel or select/
reset knob in the instrument panel,
the AVG. FUEL B appears in the
secondary display. 102
258
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
71
INFO KNOBINFO BUTTON

You can also change the display by
pushing the select/reset knob in the
instrument panel.
When you turn the ignition switch to
the ON (II) position, what you last
selected is displayed. While
a trip meter is displayed, you
can change the display between
‘‘Trip A’’ and ‘‘Trip B’’ by pressing
the SEL/RESET button on the
steering wheel, or the select/reset
knob in the instrument panel.
To reset a trip meter, display it, and
press and hold the SEL/RESET
button or select/reset knob until the
number resets to ‘‘0.0.’’ When you
reset ‘‘Trip B’’ , ‘‘AVG. FUEL B’’ is
also reset. If you reset ‘‘Trip A’’,
‘‘AVG. FUEL A’’ and ‘‘AVG. SPEED’’
willberesetatthesametime.
In
the lower segment, each time you
press the SEL/RESET button on the
steering wheel, the display changes
from ‘‘Trip A/Odome ter’’ to ‘‘Trip A/
Outside Temperature’’ to ‘‘Trip B/
Outside Temperature’’ to ‘‘Engine
OilLife,’’andthenbacktothe
‘‘Trip A/Odometer’’ as shown on
page . 70
Multi-Inf ormation Display
Trip Meter
72
U.S.model is shown
SELECT/RESET
KNOB
SEL/RESET
BUTTON
LOWER SEGMENT

This shows the outside Fahrenheit
temperature in U.S. models, and
Centigrade temperature in Canadian
models. The
temperature sensor is in the
front bumper. The temperature
reading can be affected by heat
reflection from the road surface,
engine heat, and the exhaust from
surrounding traffic. This can cause
an incorrect temperature reading
when your vehicle speed is under
19 mph (30 km/h). When you start
your trip, the sensor is not fully
acclimatized, therefore it may take
several minutes until the proper
te mperature is displayed.
In certain weather conditions,
temperature readings near freezing
(32°F, 0°C) could mean that ice is
forming on the road surface.
You can adjust the outside
temperature display (see page ).This
shows the remaining life of the
engine oil. It shows 100% after the
engine oil is replaced and the display
is reset. The engine oil life is
calculated based on engine operating
conditions and accumulated engine
revolutions. For more inf ormation,
see page .
96
274
Multi-Inf ormation Display
Outside Temperature Engine Oil Lif e
Inst rument s and Cont rols
73
U.S.model is shownOUTSIDE TEMPERATURE
U.S.model is shownENGINE OIL LIFE

When the engine oil life reaches 15 %,
the display shows ‘‘SERVICE DUE
SOON’’ and the code for the
maintenance items to be performed.
When the engine oil life reaches 5 %,
the display shows ‘‘SERVICE DUE
NOW’’ along with the same
maintenance items. Have
your dealer do the indicated
maintenance as soon as you see this
message, and have them reset the
display after completing the service.
If you do not perform the indicated
maintenance or do not reset the
display, the message changes to
‘‘SERVICE PAST DUE’’ when the
engine oil life becomes 0 %. These
messages appear on the multi-
info rmation display each time you
turn the ignition switch to the ON
(II) position.
For more information about
Maintenance Messages, see
‘‘ ’’ on page
.
Also refer to page for important
maintenance saf ety precautions. 272
274
Multi-Inf ormation Display
Maintenance Messages
Maintenance Minder
74
U.S.model is shown

CONT INUED
If there is a problem with your
vehicle, f or example, the engine oil
level is low or a door is not f ully
closed, the multi-inf ormation display
will show you the problem. It does
this by interrupting the current
display with one or more messages.The system message(s) triggers the
appropriate indicator(s) on the
instrument panel, including the
system message indicator, to come
on. The system message indicator
does not go of f until the problem(s)
is corrected.When there are several warnings to
be shown, the system switches the
messages every 5 seconds.
The message is shown until you
push the INFO button.
Toseethemessageagain,pressthe
INFO button, 5 seconds af ter the
display disappears.
Multi-Inf ormation Display
System Messages
Inst rument s and Cont rols
75
SYSTEM MESSAGE INDICATOR

Here is a table which shows the
possible multi-information display
messages and where to find further
info rmation on each message. See
page
78
See page
78
See page
78
See page
79
See page
79 See
page
79
See page 80
See page 81
See page 81
See page
81
Multi-Inf ormation Display
76

CONTINUED
See page
82
See page
82
See page
83 See
page
84
See
page
82
See page
83 See
page
84 See
page
122
See page
85
See
page
83
See page
84
Multi-Inf ormation Display
Inst rument s and Cont rols
77