2007 Acura TL buttons

Vents, Heating, and A/C
Features
127
OFF BUTTONWINDSHIELD
DEFROST BUTTON
REAR WINDOW
DEFOGGER BUTTON
FAN CONTROL
BUTTONS
DRIVER’S SIDE
TEMPERATURE
CONTROL BUTTONS
PASSENGER’S SIDE
TEMPERATURE
CONTROL BUTTONS
DUAL BUTTON RECIRCULATION BUTTON AIR CONDITIONING
BUTTON PASSENGER’S SIDE
MODE CONTROL BUTTON
DRIVER’S SIDE MODE
CONTROL BUTTON DRIVER’S AUTO BUTTON TEMPERATURE DISPLAY
PASSENGER’S AUTO BUTTON
Vehicles with navigation system
——
y

y
(%y
y

Û
Ý When
the indicator in the button is
on, air from the vehicle’s interior is
recirculated throughout the system.
When the indicator is off, air is
brought in from the outside of the
vehicle (fresh air mode).
The outside air intakes for the
heating and cooling system are at
the base of the windshield. Keep this
area clear of leaves and other debris.
Thesystemshouldbeleftinfresh
air mode under almost all conditions.
Keeping the system in reci rculation
mode, particularly with the A/C off,
can cause the windows to fog up.
Switch to recirculation mode when
driving through dusty or smoky
conditions, then return to fresh air
mode.
This button turns the rear window
def ogger of f and on (see page ).
The driver’s side temperature and
passenger’s side temperature can be
set separately. Press either side’s
button to increase the temperature
of airf low. Press either side’s
button to decrease it. When you set
the temperature to its lower limit or
its upper limit, it will be displayed as
‘‘Lo’’ or ‘‘Hi’’.
This button turns the air
conditioning on and of f . The A/C
ON indicator comes on in the display
when the A/C is on.
The climate control system in your
vehicle can also be operated using
the voice control system. See the
navigation section in your quick start
guide f or an overview of this system
and the navigation system manual
f or complete details.
Press the button to increase the
fanspeedandairflow.Pressthe
button to decrease it.
90
Only on models with navigation system
Airflow Buttons
Voice Control SystemRecirculation Button
Rear Window Def ogger Button
Temperature Control Buttons
Air Conditioning (A/C) Button
Fan Control Buttons
128
——
y
y
(%y
y

Use the mode control button to
select the vents the air flows from.
Some air will flow from the
dashboard vents in all modes.Air flows from the center
and corner vents in the dashboard.
Air f lows f rom the def roster
vents at the base of the windshield. Air f lows f rom the f loor
vents. When you select , the
system automatically switches to
f resh air mode. Airf low is divided between
the vents in the dashboard and the
f loor vents.
Airf low is divided between
the f loor vents and the def roster
vents at the base of the windshield. When you select or ,
the system automatically switches to
f resh air mode and turns on the A/C.
In this case, you cannot turn the A/C
off.
Select and fresh air mode.
Set the f an to the desired speed.
Adjust the warmth of the air with
the temperature control buttons.
The heater uses engine coolant to
warm the air. If the engine is cold, it
will be several minutes bef ore you
f eel warm air coming f rom the
system. Set the temperature to maximum.
Make sure the A/C is of f .
Select and fresh air mode.
Set the f an to the desired speed.
You can set the temperatures and
modes f or the driver’s side and the
passenger’s side separately when
this button is pressed (indicator on).
When the indicator in the DUAL
button is off, you can adjust both
sides to the same temperature and
mode with the driver’s side temperature control buttons and
mode control button.
When is selected, the
passenger’s temperature cannot be
set separately f rom the driver’s. Thedriver’ssidemodeand
passenger’s side mode can be
selected separately when the dual
button is pressed. However, when is selected on the driver’s
side, mode selection on the
passenger’s side is not possible. The f low-through ventilation system
draws in outside air, circulates it
through the interior, then exhausts it
through vents near the rear window.
1.
2.
3.
4.
1.
2.
3.
Vents, Heating, and A/C
Mode Control Button
Using the Heater Ventilation
Dual Button
Features
129
——
y

y
(%y
y

When the AUTO button on the
driver’s side is pressed, the
temperature control buttons on the
passenger’s side are disabled, and
the interior temperature is regulated
to the temperature set on the driver’s
side.WhentheAUTObuttononthe
passenger’s side is pressed,
temperature can be set on the driver’s
side and passenger’s side separately.
The system automatically selects the
proper mix of conditioned and/or
heated air that will, as quickly as
possible, raise or lower the interior
temperature to your pref erence.
When you set the temperature to its
lower or its upper limit, the system
runs at f ull cooling or heating only. It
does not regulate the interior
temperature.
The automatic climate control
system adjusts the f an speed and
airflow levels to maintain the interior
temperature you select.
In AUTO mode, the vehicle’s interior
temperature is independently
regulated f or the driver and
passenger. If the driver’s side of the
vehicle is getting too much sun, the
system will adjust to a lower
temperature.
Press the AUTO button.
Set the desired temperature with
the temperature control buttons.
You will see AUTO in the system’s
display.
Select . The system
automatically switches to f resh air
mode and turns on the A/C. The
A/C indicator does not come on if
it was previously off.
Select .
Set the f an and temperature
controls to maximum level.
To clear the windshield f aster, you
can close the dashboard corner vents
by rotating the wheel below each
vent. This sends more warm air to
the windshield def roster vents. Once
the windshield is clear, select f resh
air mode to avoid fogging the
windows.
For your saf ety, make sure you have
a clear view through all the windows
bef ore driving. 1.
2.
1.
2.
3.
On models with navigation system
Climat e Cont rol
T o Cool or Heat A utomatically
Using A utomatic Climate Control
T o Remove Exterior Frost or Ice
From the Windows
Features
131
——
y
y
(%y
y

Audio System (Models without Navigation System)
134
SCAN BUTTONTUNE/SOUND
KNOB SEEK BUTTONS AUTO SELECT
BUTTON
PRESET BUTTONS
AM/FM BUTTON
PWR/VOL KNOB
——
y


y
(%y
y

µ
µ ´µ µ
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Turn the system on by pushing the
power/volume knob or the AM/FM
button. Adjust the volume by turning
the power/volume knob. You can use any of f ive methods to
f ind radio stations on the selected
band: tune, seek, scan, the preset
buttons, and auto select.
Use the TUNE knob to
tune the radio to a desired f requency.
Turn the knob to the right to tune a
higher f requency, and turn it to the
lef t to tune a lower f requency.
The band and f requency that the
radio was last tuned to are displayed.
To change bands, press the AM/FM
button. On the FM band, ST will be
displayed if the station is
broadcasting in stereo. Stereo
reproduction in AM is not available. The seek f unction
searches up and down from the
current f requency to f ind a station
with a strong signal. To activate it,
press the or SEEK button, then
release it. The scan f unction samples
all stations with strong signals on the
selected band. To activate it, press
the SCAN button, then release it.
You will see SCAN in the display.
The system will scan f or a station
with a strong signal. When it f inds
one, it will stop and play that station
f or about 10 seconds.
If you do nothing, the system will
scan f or the next strong station and
play it f or 10 seconds. When it plays
a station that you want to listen to,
press the SCAN button again.
CONT INUED
TUNE
SEEK SCAN
Playing the A M/FM Radio Selecting a Station
Audio System (Models without Navigation System)
Features
135
——
y

y
(%y
y

µµEach preset button can
store one frequency on AM and two
frequencies on FM.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two frequencies with each preset
button.
Usethetune,seek,orscan
function to tune the radio to a
desired station.
Repeat steps 1 through 3 to store a
total of six stations on AM and
twelve stations on FM.
Pick
a preset button, and hold it
until you hear a beep. If
you are
traveling far from home and can no
longer receive your preset stations,
you can use the auto select feature to
find stations in the local area.
Press the A. SEL button. You will see
A. SEL flashing in the display, and
the system goes into scan mode for
several seconds. It stores the
frequencies of six AM, and twelve
FM stations in the preset buttons.
You will see a ‘‘0’’ displayed after
pressing a preset button if auto
select cannot find a strong station for
every preset button. If
you do not like the stations auto
select has stored, you can store
other frequencies on the preset
buttons as previously described.
press the
A. SEL button. This restores the
presets you originally set.
For inf ormation on AM/FM radio
f requencies and reception, see page .
1.
2.
3.
4.
178
To turn of f auto select,
Preset
A UT O SEL ECT
Audio System (Models without Navigation System)
136
——
y
y
(%y

y

µµ
Î
Î
Adjusts the volume level
basedonthevehiclespeed. This
function is set to MID as the
default setting when the vehicle
leaves the factory. You
can use the instrument panel
brightness control buttons to adjust
the illumination of the audio system
(see page ). The audio system
illuminates when the parking lights
are on, even if the radio is of f .
The SVC mode controls the volume
based on vehicle speed. The f aster
you go, the louder the audio volume
becomes. As you slow down, the
audio volume decreases.
The SVC has f our modes; SVC OFF,
SVC LOW, SVC MID, and SVC
HIGH. Turn the TUNE knob to
adjust the setting to your liking. If
you f eel the sound is too loud,
choose low. If you f eel the sound is
too quiet, choose high. Dolby
PL (Prologic) II signal processing
creates multi-channel surround
sound f rom the audio signal
recorded with two channel stereo
sources. Dolby prologic II can only
activate when using the CD (CD-DA,
MP3/WMA),XMradio,andAUX
audio modes. When it activates,
‘‘DPL II’’ is shown on the upper
display.
Manuf actured under license f rom
Dolby Laboratories. ‘‘Dolby’’,
‘‘ProLogic’’, and the double-D symbol
are trademarks of Dolby
Laboratories. 89
SVC
A udio System L ighting
Dolby PL (Prologic) II
Speed-sensit ive Volume Compensat ion (SVC)
Audio System (Models without Navigation System)
138
——
y
y
(%y
y