2007 Acura RL Owner's Manual

CONTINUED
If you are replacing a driver’s side
bulb, slide the battery toward the
engine to get more clearance (see
page ).
Use a flat-tipped screwdriver to
remove the holding clip from the
windshield washer reservoir.
(Passenger’s
side)
Remove
the left or right side
engine compartment cover (see
page ).
Pull the bulb straight out of its
socket. Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
(Driver’s side)
Reinstall the battery and the
battery cover.
Reinstall the engine compartment
side cover.
1.
2.
5.
6.
7.
8. 394
424
4.
On model without adaptive f ront
lighting system
Lights
Replacing a Front Position/Side
Marker L ight Bulb
Maint enance
407
SOCKET
BULB
——
y

y
(y
y

Your vehicle uses halogen light
bulbs. When replacing a bulb, handle
it by its plastic case, and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
(Driver’s side)
Reinstall the battery and the
battery cover.
(Passenger’s side)
Reinstall the windshield washer
reservoir.
Reinstall the engine compartment
side cover.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. 5.
6.
7.
8.
9.
3.
4.
Lights
ReplacingaFogLightBulb
408
SOCKET
HOLDING CLIP
BULB
Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.
——
y

y
(y
y

Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the f og lights to test the
new bulb.
Reinstall the two mounting bolts
onthesideundercoverand
tighten them securely. Put the
holding clip back on the side
under cover and push on the
center until it locks (the center is
flushwiththehead).
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it one-
quarter turn counterclockwise.
Caref ully push up the side under
cover into the bumper. Use a Phillips-head screwdriver to
remove the two mounting bolts,
and remove the holding clip with a
f lat-tipped screwdriver. 3.
4. 5.
6.
8. 7.
1.
2.
Lights
Maint enance
409
CLIP CONNECTORBULB
BOLTS
——
y

y
(y
y

Determine which of the two bulbs
is burned out: turn signal or back-
up light.
Remove the socket by turning it
one-quarter turn counterclockwise.
Remove the burned out bulb by
pulling it straight out of its socket.
Open the trunk lid, and remove
the lef t or right maintenance lid.
Remove the mounting nut with an
8mmwrench.
Carefully pry in the top or bottom
edge of the trim with a small f lat-
tipped screwdriver, and pull the
trim straight back.
Remove the two mounting bolts
with an 8 mm wrench.
Pull the taillight assembly straight
back out of the body.
2. 1.
3.
4.
5.6.
7.
8.
Lights
Replacing Rear Bulbs
410
MOUNTING NUT
MAINTENANCE LID BOLTS
BULBS
TAIL LIGHT TRIM SOCKETS
——
y

y
(y
y

Install the new bulb in the socket
by pushing it straight in the socket
until it bottoms.
Reinstall the socket into the light
assembly. Turn it clockwise to
lock it in place.
Testthelightstomakesurethe
new bulb is working.
Tighten the mounting nut securely,
and reinstall the maintenance lid. When reinstalling the taillight
assembly, align and pop the snap
f asteners in place. Tighten the two
mounting bolts and reinstall the
trim in place.If your seat belts get dirty, use a sof t
brush with a mixture of mild soap
and warm water to clean them. Do
not use bleach, dye, or cleaning
solvents. Let the belts air-dry bef ore
you use the vehicle.
Dirt build-up in the loops of the seat
belt anchors can cause the belts to
retract slowly. Wipe the insides of
the loops with a clean cloth
dampened in mild soap and warm
water or isopropyl alcohol.
This f ilter removes the dust and
pollenthatisbroughtinfromthe
outside through the climate control
system.
Have your dealer replace the filter
when this service is indicated by a
maintenance message in the multi-
inf ormation display. It should be
replaced every 15,000 miles (24,000
km) if you drive primarily in urban
areas that have high concentrations
of soot in the air, or if the f low f rom
theclimatecontrolsystembecomes
less than usual.
9.
10.
11.
12.
13. Cleaning the Seat Belts
Dust and Pollen Filter
Lights, Dust and Pollen Filter, Cleaning the Seat Belts
Maint enance
411
LOOP
——
y

y
(y
y

Make sure the rear f loor mats are
properly hooked to the f loor mat
anchors. Your vehicle is equipped
with front passenger’s seat weight
sensors. If the rear passenger’s f loor
mat is on the seat rail of the front
passenger’s seat, the sensors will
detect the decreased weight on the
seat, and they may not work properly.
If you use a non-Acura f loor mat,
make sure it f its properly and that it
canbeusedwiththefloormat
anchors. Do not put additional f loor
mats on top of the anchored mats.
If you remove a f loor mat, make sure
tore-anchoritwhenyouputitback
in your vehicle. The floor mats that came with your
vehicle hook over f loor mat anchors.
This keeps the f loor mats f rom
sliding f orward or backward and
possibly interf ering with the pedals
or making the f ront passenger’s
weight sensors inef f ective. Floor Mats
Floor Mat s
412
HOOK HOOK HOOK
Front
Front Front
DRIVER’S SIDE FLOOR MAT
FRONT PASSENGER’S
SIDE FLOOR MATREAR PASSENGER’S FLOOR MAT
——
y


y
(y
y

Push the end of the cover on the
blade assembly until the other end
is pivo ted out, and remove the
cover.
Disconnect the blade assembly
from the wiper arm by removing
the two screws from the arm.
Adjust
the windshield wiper arms
to the winter position by holding
bothwiperarmsasshowninthe
illustration at the same time (see
page ). Raise the wiper arms
of f the windshield.
Check the condition of the wiper
blades at least every 6 months.
Replace them if you f ind signs of
cracking in the rubber, areas that are
getting hard, or if they leave streaks
and unwiped areas when used.
2.
1.
3.
139
Wiper Blades
Maint enance
413
COVER
SCREWS
WIPER ARMS
HOLDING LOCATIONS
BLADE
Do not open the hood when the wiper
arms are raised, or you will damage
the hood and the wiper arms.
——
y

y
(y
y

Remove the blade f rom its holder
by grasping the tabbed end of the
blade. Pull f irmly until the tabs
come out of the holder.Examine the new wiper blades. If
they have no plastic or metal
reinf orcement along the back
edge, remove the metal
reinf orcement strips f rom the old
wiper blade, and install them in
the slots along the edge of the new
blade.Slide the new wiper blade into the
holder until the tabs lock.
Reinstall the blade assembly to the
wiper arm and tighten the two
screws securely. Reinstall the
cover by pushing it in.
Set the wiper arms back on the
windshield. Adjust the windshield
wipers to their previously parked
position.
4. 5. 6.
7.
8.
Wiper Blades
414
BLADE
BLADE
REINFORCEMENT
——
y

y
(y
y