Page 121 of 442
ÛÝ
To exit AUTO DOOR UNLOCK
without changing the current setting,
select EXIT by pressing the INFO
( / ) button, then press the SEL/
RESET button. The screen goes
back to CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE MENU.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE MENU. If this
happens, you need to repeat the
same procedure.
Multi-Inf ormation Display
Inst rument s and Cont rols
117
——
yy
() y
y
Page 124 of 442

µµ
µ µ
ON
OFF
Rear Window Wiper and Washer
Rear Window Washer The wiper is not activated.
When you turn the wiper switch to
OFF while the rear window wiper is
in action, it will return to its parked
position. Hold past ON to turn the rear
window wiper on and to spray the
rear window washer. The rear
window wiper makes one more
sweep after you release the switch.
Rotate the switch clockwise
to turn the rear window wiper ON.
The wiper operates intermittently. When the wiper control lever
position is INT, the rear wiper
operates intermittently. When it is
LO or HI, the rear wiper operates
continuously.
Rotate
the switch counterclockwise from
OFF to spray the window washer
without activating the wiper. The
washer will operate until you release
the switch.
Therearwindowwasherusesthe
same f luid reservoir as the wind-
shield washer.
When you shif t the transmission to
the reverse position with the f ront
windshield wipers activated, the rear
window wiper operates automatically.
1.
2.
3.
4. Rear Window Wiper and Washer OFF Rear Window Wiper and Washer
ON Rear Window Washer
Windshield Wipers and Washers
120
——
y
y
() y
y
Page 125 of 442

µµPush down on the
lever to signal a lef t turn and up to
signal a right turn. To signal a lane
change, push lightly on the lever,
and hold it. The lever will return to
center when you release it or
complete a turn. Turning the switch to
the ‘‘ ’’ position turns on the
parking lights, taillights, instrument
panel lights, side-marker lights, and
rear license plate lights.
Turning the switch to the ‘‘ ’’
position turns on the headlights.
When the light switch is in the
‘‘ ’’ or ‘‘ ’’ position, the
lights on indicator comes on as a
reminder. This indicator stays on if
you leave the light switch on and
turn the ignition switch to the
ACCESSORY (I) or the LOCK (0)
position.
Turn signal
Of f
Parking and interior lights
Headlights
High beams
Flashhighbeams
Fog lights of f
Fog lights on
If you leave the lights on with the
key removed f rom the ignition
switch, you will hear a reminder
beeper when you open the driver’s
door.
1.
2.
3.
4.
5.
6.
7.
8.
CONT INUED
Turn Signal and Headlights
Turn Signal
Headlights
Inst rument s and Cont rols
121
——
y
y
() y
y
Page 127 of 442
The lights will turn on again when
you unlock or open the driver’s door.
If you unlock the door, but do not
open it within 15 seconds, the lights
will go off. With the driver’s door
open, you will hear a lights on
reminder beeper. Wi
th the headlight switch off or in
the position, the high beam
headlights and the high beam
indicator come on with reduced
brightness when you turn the
ignition switch to the ON (II)
position and release the parking
brake. They remain on until you turn
the ignition switch off, even if you
set the parking brake.
The headlights revert to normal
operation when you turn them on
with the switch.
You can change the ‘‘HEADLIGHT
AUTO OFF TIMER’’ setting on the
multi-inf ormation display (see page
).
105
On RDX with Technology Package
model
Daytime Running L ights
Headlights
Inst rument s and Cont rols
123
——
y
y
() y
y
Page 130 of 442

Make any steering wheel adjustment
bef ore you start driving.Push the lever under the steering
column all the way down.
Move the steering wheel so it
points toward your chest, not
toward your f ace. Make sure you
can see the instrument panel
gauges and indicators. The master key fits all the locks on
your vehicle. The valet key works
only in the ignition and the door
locks. You can keep the glove box
and console compartment locked
when you leave your vehicle and the
valet key at a parking f acility.
Push the lever up to lock the
steering wheel in position.
Make sure you have securely
locked the steering wheel in place
by trying to move it up, down, in,
and out.
1.
2. 3.
4.
Steering Wheel A djustment, K eys and L ocks
Steering Wheel A djustment
K eys
126
LEVERVALET KEY
(Light Gray)
KEY
NUMBER
TAG MASTER KEYS
WITH REMOTE
TRANSMITTER
Adjusting the steering wheel
position while driving may
cause you to lose control of the
vehicle and be seriously injured
inacrash.
Adjust the steering wheel only
when the vehicle is stopped.
——
y
y
() y
y
Page 131 of 442

Youshouldhavereceivedakey
number tag with your keys. You will
need this key number if you ever
have to get a lost key replaced. Use
only Acura-approved key blanks.
These keys contain electronic
circuits that are activated by the
immobilizer system. They will not
work to start the engine if the
circuits are damaged.
Protect the keys from direct
sunlight, high temperature, and
high humidity.
Donotdropthekeysorsetheavy
objects on them.
Keep the keys away from liquids.
If they get wet, dry them
immediately with a soft cloth.
The valet key does not contain a
battery. Do not try to take it apart. The
master key can be retracted into
the remote transmitter. When you
use the key, push the release button
to pop the key out of the remote
transmitter. To retract the key, push
the release button and at the same
time push the key into the remote
tran smitter until it is secu rely
latched. Always
use the fully-extended key
when you insert it to the ignition
switch. If the key does not fully
extend, the immobilizer system may
not operate properly and preven ts
from starting the engine.
Retracting or extending the key may
hurt your f inger. Make sure your
f ingers do not touch the pivot of the
key when retracting or extending the
key.
Your vehicle has two transmitters;
see page for an explanation of
the operation. 140
Keys and Locks
Retractable Master Key
Remote Transmitter
Inst rument s and Cont rols
127
RELEASE BUTTONPush
——
y
y
() y
y
Page 132 of 442

As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.The immobilizer system protects
your vehicle f rom thef t. If an
improperly-coded key (or other
device) is used, the engine will not
start.
When you turn the ignition switch to
the ON (II) position, the immobilizer
system indicator should come on
brief ly, then go of f . If the indicator
starts to blink, it means the system
does not recognize the coding of the
key. Turn the ignition switch to the
LOCK (0) position, remove the key,
reinsert it, and turn the ignition
switch to the ON (II) position again. If you have lost your key and cannot start the engine, contact your dealer. Do not attempt to alter this system
or add other devices to it. Electrical
problems could result that may make
your vehicle undrivable. If the system repeatedly does not
recognize the coding of your key,
contact your dealer. The system may not recognize your
key’s coding if another immobilizer
key or other metal object (i.e. key
f ob) is near the ignition switch when
you insert the key.
Immobilizer System
128
——
y
y
() y
y
Page 133 of 442
µµ
µ
µ
The ignition switch has f our
positions: LOCK (0), ACCESSORY
(I), ON (II), and START (III). This is the normal key
position when driving. Several of the
indicators on the instrument panel
come on as a test when you turn the
ignition switch f rom the
ACCESSORY (I) to the ON (II)
position.
Use this position
only to start the engine. The switch
returns to the ON (II) position when
you let go of the key.
You can insert or
remove the key only in this position.
To turn the key, the shift lever must
be in Park, and you must push the
key in slightly.
If the f ront wheels are turned, the
anti-theft lock may make it difficult
to turn the key. Firmly turn the
steering wheel to the lef t or right as
you turn the key.
You can
operate the audio system and the
accessory power sockets in this
position.
CONT INUED
Ignition Switch
ON (II)
ST A RT (III)
LOCK (0)
A CCESSORY (I)
Inst rument s and Cont rols
129
——
y
y
() y
y