2007 Acura MDX Owner's Manual

You can open and close the windows
and moonroof with the key in the
driver’s door lock.Insert the key in the driver’s door
lock.
Turn the key clockwise, then
release it. Turnthekeyclockwiseagain,and
hold it. All f our windows and
moonroof start to open. To stop
the windows and the moonroof ,
release the key.
When the windows or moonroof
stops bef ore opening f ully, to open
the windows and moonroof f urther,
turnandholdthekeyagain
(within 5 seconds).
To close: Insert the key in the driver’s door
lock.
Turn the key counterclockwise,
then release it.
Turn the key counterclockwise
again, and hold it. All four
windows and the moonroof start to
close. To stop the windows and
the moonroof , release the key.
To open:
You can open all of the windows and
the moonroof f rom outside with the
remote transmitter.
Press the UNLOCK button once
to unlock the driver’s door.
Press the UNLOCK button a
second time, and hold it. All the
doors unlock, and all f our windows
and moonroof start to open. To
stop the windows and moonroof ,
release the button.
To open the windows and
moonroof f urther, press the
button again and hold it. If the
windows and the moonroof stop
bef ore the desired position, repeat
steps 1 and 2.
You cannot close the windows or the
moonroof with the remote
transmitter. 1.
2.
2.
3. 3.
1.
2.
3. 4.
1.
CONT INUED
Power Windows, Moonroof
Opening/Closing the Windows
and Moonroof with the K ey
Opening the Windows and
Moonroof with the Remote
Transmitter
Inst rument s and Cont rols
149
——y
y
()-y
y

To close the windows and
moonroof f urther, turn and hold
the key again (within 5 seconds).To open the moonroof f ully, pull
back the moonroof switch f irmly.
The moonroof opens all the way. To
stop the moonroof f rom opening
f ully, push the switch brief ly. To tilt up the moonroof , push on the
center of the moonroof switch. To
stop the moonroof f rom tilting up
f ully, push the switch brief ly.
To open or close the moonroof
partially, pull back or push f orward
the moonroof switch lightly and hold
it. The moonroof will stop when you
release the switch.
To close the moonroof f ully, f irmly
push the moonroof switch f orward,
then release it. The moonroof
automatically closes all the way. To
stop the moonroof f rom closing,
push the switch briefly.
NOTE: If the windows and moonroof
stop bef ore the desired position,
repeat steps 2 and 3. 4.
Moonroof
Power Windows, Moonroof
150
MOONROOF SWITCH
——y
y
()-y
y
Auto reverse does not work when
closing the windows and
moonroof with the key.

You can open and close the
moonroof for up to 10 minutes after
you turn off the ignition switch.
Opening either front door cancels
this function.
To apply the parking brake, push the
pedal down with your foot. To
release it, pull the release handle
fully. The parking brake indicator on
the instrument panel should go out
when the p arking brake is fully
released, and the ignition switch is in
the ON (II) position (see p age ).
If the moonroof runs into any
obstacle while it is closing
automati
cally, it will reverse
direction, and then stop. To close the
moonroof, remove the obstacle, then
use the moonroof switch again.
Auto reverse stops sensing when the
moonroof is almost closed. You
should always check that all
passengers and objects are away
from the moonroof before closing it.
129
CONTINUED
Parking Brake
AutoReverse
Moonroof, P arking Brake
Instrument sand Cont ro ls
151
RELEASE HANDLE
PARKING BRAKE PEDAL
Opening or closing the
moonroof on someone’s hands
or fingers can cause serious
injury.
Make sure all hands and fingers
are clear of the moonroof
before opening or closing it. I
f y
ou try
to open the moonroof in
below-freezing temperatures, or when
it is covered with snow or ice, you c an
damage the moonroof panel or its
motor.
——y
y
()-y
y
Auto reverse does not work when
closing the windows and
moonroof with the key.
You will also see a "RELEASE
PARKING BRAKE" message on the
multi-information display (see
page 82).

Keeptheinsideandoutsidemirrors
clean and adjusted f or best visibility.
Be sure to adjust the mirrors bef ore
you start driving.The inside mirror has day and night
positions. The night position reduces
glare f rom headlights behind you.
Flip the tab on the bottom edge of
the mirror to select the day or night
position.
On U.S. models
Mirrors
Parking Brake, Mirrors
152
U.S. models
TAB
Driving the vehicle with the parking
brake applied can damage the rear
brakes and axles. A beeper will sound
if the vehicle is driven with the parking
brake on.
——y
y
()-y
y

The inside mirror can automatically
darken to reduce glare. To turn on
this feature, press the button on the
bottom of the mirror. The AUTO
indicator comes on as a reminder.
When it is on, the mirror darkens
when it senses the headlights of a
vehicle behind you, then returns to
normal visibility when the lights are
gone. Press the button again to turn
of f this sensing.Turn the ignition switch to the ON
(II) position.
Move the selector switch to L
(driver’s side) or R (passenger’s
side).
1.
2.
On Canadian models
CONT INUED
Adjusting the Power Mirrors
Mirrors
Inst rument s and Cont rols
153
Canadian models
SELECTOR
SWITCH
AUTO BUTTON
INDICATOR SENSOR
There is also a sensor on the back of
the mirror. Items hung on the mirror
may block this sensor and af f ect
perf ormance.
——y
y
()-y
y

Push the appropriate edge of the
adjustment switch to move the
mirrorright,left,up,ordown.
When you finish, move the
selector switch to the center (off)
position. This turns the
adjustme nt switch off to keep your
settings.
The outside mirrors are heated to
remove fog and frost. With the
ignition switch in the ON (II)
position, turn on the heaters by
pressing the button. The indicator in
the button comes on as a reminder.
Press the button again to turn the
heaters off.
Depending
on the position of the
selector switch, the left or right side
mirror will pivot downward slightly
when you shift the transmission into
reverse. In the left position, the left
mirror pivots. In the right position,
the right mirror pivots. This gives
you a better view of that side of the
vehicle while parallel parking. The
mirror returns to its original position
when you take the transmission out
of reverse. To turn this feature off,
leave the switch in the center
position.
Outside mirror positions can be
stored in the driving position
memory system (see page ).
4. 3.
155
Mirrors
Heated Mirrors
154
HEATED MIRROR BUTTON
——y
y
()-y
y

Adjust the seat to a comfortable
position (see page ).
Store
a driving position only when
the vehicle is parked.
Turn the ignition switch to the ON
(II) position. You cannot add a
new driving position to the
memory unless the ignition switch
is in the ON (II) position. You can
recall a memorized position with
the ignition switch in any position.
Your
vehicle has a memory feature
for the steering wheel, driver’s seat,
and outside mirror positions.
Seat, except for power lumbar,
steering wheel and outside mirror
positionscanbestoredinseparate
memories. You select a memorized
position by pushing the appropriate
button or using the appropriate
remote transmitter (Driver 1 or
Driver 2). For more information see
page .
Press and release the MEMO
buttononthecontrolpanel.You
will hear a beep. Immediately
press and hold one of the memory
buttons (1 or 2) until you hear two
beeps. The indicator in the
memory button will come on. The
current positions of the driver’s
seat, steering wheel, and outside
mirrors are now stored.
Adjust
the steering wheel to a
comf ortable position (see page ).
Adjust the outside mirrors f or best
visibility (see page ). 3.
1.
2.
139
124140
153
CONT INUED
Storing a Driving Position in
Memory
Driving Position Memory System
Inst rument s and Cont rols
155
MEMO BUTTON
MEMORY BUTTONS
——y

y
()-y
y

Doing any of the following after
pressing the MEMO button will
cancel the storing procedure.
Not pressing a memory button
wi thin 5 seconds.
Readjusting the seat position.
Readjust the outside mirror
position.
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory. If
you want to add a new position while
retaining the current one, use the
other memory button. To
select a memorized position, do
this: To
stop the system’s automatic
ad justment, do any of these actions:
Press any button on the control
panel: MEMO, 1, or 2.
Push any of the adjustment
switches for the seat.
Shift out of Park.
Adjust the outside mirrors.
Make
sure the vehicle is parked.
Press the desired memory button
(1 or 2) until you hear a beep, then
release the button.
To change the ‘‘MEMORY
POSITION LINK’’ setting, see page . If desired, you can use the
adjustment switches to change the
positions of the seat, steering wheel
or outside mirrors af ter they are in
their memorized position. If you
change the memorized position, the
indicator in the memory button will
go out. To keep this driving position
f or later use, you must store it in the
driving position memory.
The system will move the seat,
steering wheel, and outside mirrors
to the memorized positions. The
indicator in the selected memory
button will f lash during movement.
When the adjustments are complete,
you will hear two beeps, and the
indicator will remain on. 1.
2.
98
Selecting a Memorized Position
Driving Position Memory System
156
——y


y
()-y

y