2007.5 Peugeot 307 service
[x] Cancel search: servicePage 24 of 212
INSTRUMENTS and CONTROLS
24
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and trip distances).
Note : the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver’s door, as well as on lock-
ing and unlocking the vehicle.
It also displays the information relat-
ing to the cruise control or speed lim-
iter, when either of these is activated
(see corresponding section).
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer’s servicing schedule.
The point at which the next service
is due is calculated from the last indi-
cator zero reset (see corresponding
section). It is determined by two pa-
rameters:
- the distance travelled,
- the time which has elapsed since the last service.
Note: the distance remaining before
the next service may be weighted by
the time factor, depending on the us-
er’s driving habits. DISPLAY
In the event of under-revving or over-
r e v v i n g , t h e g e a r s e l e c t e d l a s h e s f o r
a few seconds, then the actual gear
engaged is displayed
This comes on when the
"SPORT" programme on
the automatic gearbox is se-
lected.
This comes on when the
"SNOW" programme on the
automatic gearbox is select-
ed.
A u t o m a t i c g e a r b o x i n d i c a t o r
l i g h t s
"SNOW" indicator light This is displayed if a gear is
not engaged correctly (selec-
tor between two positions).
"SPORT" indicator light
Invalid value during manual
operation
Page 25 of 212
INSTRUMENTS and CONTROLS
24
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and trip distances).
Note : the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver’s door, as well as on lock-
ing and unlocking the vehicle.
It also displays the information relat-
ing to the cruise control or speed lim-
iter, when either of these is activated
(see corresponding section).
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer’s servicing schedule.
The point at which the next service
is due is calculated from the last indi-
cator zero reset (see corresponding
section). It is determined by two pa-
rameters:
- the distance travelled,
- the time which has elapsed since the last service.
Note: the distance remaining before
the next service may be weighted by
the time factor, depending on the us-
er’s driving habits. DISPLAY
In the event of under-revving or over-
r e v v i n g , t h e g e a r s e l e c t e d l a s h e s f o r
a few seconds, then the actual gear
engaged is displayed
This comes on when the
"SPORT" programme on
the automatic gearbox is se-
lected.
This comes on when the
"SNOW" programme on the
automatic gearbox is select-
ed.
A u t o m a t i c g e a r b o x i n d i c a t o r
l i g h t s
"SNOW" indicator light This is displayed if a gear is
not engaged correctly (selec-
tor between two positions).
"SPORT" indicator light
Invalid value during manual
operation
Page 26 of 212
INSTRUMENTS and CONTROLS
Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display in-
dicates the number of miles [kilome-
tres] (rounded off) remaining until the
next service.
E x a m p l e : 4,800 miles/km remain be-
f o r e t h e n e x t s e r v i c e . F o r i v e s e c o n d s
after the ignition is switched on, the
display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance. T h e s e r v i c e i s o v e r d u e .
T h e s p a n n e r l a s h e s f o r 5 s e c o n d s
after the ignition is switched on.
E x a m p l e : the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and the
spanner remains lit. The display indi-
cates the total and trip distance.
Note: the spanner may also come on
if more than two years have elapsed
since the last service.
T h e d i s t a n c e r e m a i n i n g t o
t h e n e x t s e r v i c e i s l e s s t h a n
5 0 0 m i l e s ( 1 , 0 0 0 k m ) .
E x a m p l e : 400 miles (900 km) remain
before the next service.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
t h e s p a n n e r r e m a i n s l i t .
It indicates that a service must be
carried out soon. The display indi-
cates the total and trip distance.
Page 27 of 212
INSTRUMENTS and CONTROLS
26
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
Switch off the ignition,
Press and hold the trip recorder
reset button,
Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
Important: after this operation, if you
wish to disconnect the battery, lock
t h e v e h i c l e a n d w a i t f o r a t l e a s t i v e
minutes, otherwise the zero re-set
will not be registered.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for a few
seconds, after the service information.
Oil level correct
O i l l e v e l g a u g e f a u l t Flashing of " O I L - - "
indicates a malfunc-
tion of the engine oil
level gauge.
Contact a PEUGEOT dealer.
T h e l e v e l r e a d w i l l o n l y b e c o r r e c t
i f t h e v e h i c l e i s o n l e v e l g r o u n d
a n d t h e e n g i n e h a s b e e n o f f f o r
m o r e t h a n 1 5 m i n u t e s .
Flashing of
"OIL" ,
linked with the
service warning
light, accompa-
nied by an audible
signal and a mes-
sage on the multifunction display, in-
dicates a lack of oil which could dam-
age the engine.
I f t h e l a c k o f o i l i s c o n i r m e d b y a
check using the dipstick, it is essen-
tial that the level is topped up.
L a c k o f o i l D i p s t i c k
There are 2 marks on the
dipstick:
- never exceed level A,
- in position B, top up t h e l e v e l v i a t h e o i l i l l e r
cap, using the type of
oil suited to your en-
gine.
A = max.
B = min.
S e r v i c e i n d i c a t o r z e r o r e - s e t
Page 67 of 212
ACCESS
64
ELECTRONIC ENGINE
IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by any-
one who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
is recognised and starting is possi-
ble.
If the system does not function
correctly, the service warning light
comes on, accompanied by an audi-
ble signal and a message on the mul-
tifunction display.
In this case, your vehicle will not
start. Contact a PEUGEOT dealer as
soon as possible.
A heavy object attached to the key
(key ring, ...), weighing down on the
shaft of the key in the switch, may
cause a malfunction.
Battery ref.: CR1620/3 volts.
T h e i n f o r m a t i o n " b a t t e r y l a t " i s g i v e n
by displaying of the service warning
light, accompanied by an audible sig-
nal and a message on the multifunc-
tion display.
To replace the battery, unclip the cas-
ing using a coin at the notch.
If the remote control does not work
after the battery has been changed,
reprogramme the remote control.
Key in ignition
A buzzer sounds on opening the driv-
er’s door, if the key has been left in
the ignition.
control battery or in the event of a re-
mote control malfunction, the remote
control must be reinitialised.
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking
button immediately for a few sec-
onds.
Switch off the ignition and remove
the remote control key from the
ignition lock.
The remote control is now working
again.
Locating your vehicle
Using the key
Turn the key in the lock on the
driver’s door to lock the vehicle.
T u r n t h e k e y a g a i n w i t h i n i v e
seconds to deadlock the vehicle.
E a c h a c t i o n i s c o n i r m e d b y i x e d
lighting of the direction indicators for
approximately two seconds.
When the vehicle is locked,
if unlocking is activated inad-
vertently without a door being
opened within 30 seconds,
the vehicle will lock automatically.
The folding and unfolding of the ex-
terior mirrors can be deactivated by
a PEUGEOT dealer.
To locate your vehicle, if
you have locked it, in a
car park:
press button B , the courtesy lights
come on and the direction indica-
t o r s l a s h f o r a f e w s e c o n d s .
Changing the remote control
battery
Reprogramming the remote
control
Following disconnection of the vehi-
cle’s battery, replacement of the remote
Page 69 of 212
ACCESS
64
ELECTRONIC ENGINE
IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by any-
one who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
is recognised and starting is possi-
ble.
If the system does not function
correctly, the service warning light
comes on, accompanied by an audi-
ble signal and a message on the mul-
tifunction display.
In this case, your vehicle will not
start. Contact a PEUGEOT dealer as
soon as possible.
A heavy object attached to the key
(key ring, ...), weighing down on the
shaft of the key in the switch, may
cause a malfunction.
Battery ref.: CR1620/3 volts.
T h e i n f o r m a t i o n " b a t t e r y l a t " i s g i v e n
by displaying of the service warning
light, accompanied by an audible sig-
nal and a message on the multifunc-
tion display.
To replace the battery, unclip the cas-
ing using a coin at the notch.
If the remote control does not work
after the battery has been changed,
reprogramme the remote control.
Key in ignition
A buzzer sounds on opening the driv-
er’s door, if the key has been left in
the ignition.
control battery or in the event of a re-
mote control malfunction, the remote
control must be reinitialised.
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking
button immediately for a few sec-
onds.
Switch off the ignition and remove
the remote control key from the
ignition lock.
The remote control is now working
again.
Locating your vehicle
Using the key
Turn the key in the lock on the
driver’s door to lock the vehicle.
T u r n t h e k e y a g a i n w i t h i n i v e
seconds to deadlock the vehicle.
E a c h a c t i o n i s c o n i r m e d b y i x e d
lighting of the direction indicators for
approximately two seconds.
When the vehicle is locked,
if unlocking is activated inad-
vertently without a door being
opened within 30 seconds,
the vehicle will lock automatically.
The folding and unfolding of the ex-
terior mirrors can be deactivated by
a PEUGEOT dealer.
To locate your vehicle, if
you have locked it, in a
car park:
press button B , the courtesy lights
come on and the direction indica-
t o r s l a s h f o r a f e w s e c o n d s .
Changing the remote control
battery
Reprogramming the remote
control
Following disconnection of the vehi-
cle’s battery, replacement of the remote
Page 76 of 212
ACCESS
69
To switch on
Press and hold button A .
Activation of the function is accom-
panied by a message on the multi-
function display.
Automatic central locking of the
doors
The doors can lock automatically
when you are driving (at a speed of
more than 6 mph (10 km/h)).
Above 6 mph (10 km/h), press button
A
b r i e l y t o u n l o c k t h e d o o r s t e m p o r a r i l y .
You can activate or deactivate this
function .
To switch off
Press and hold button A .
Deactivation of the function is ac-
companied by a message on the
multifunction display. "Door open" alert
If a door has not been closed properly:
-
when the engine is running ,
you are warned by a diagram and
a message on the multifunction
display for a few seconds,
- when the vehicle is moving
(speed above 6 mph (10 km/h)),
the service warning light comes on.
This is accompanied by an audible
signal, a message and a diagram
on the multifunction display for a few
seconds.
This prevents either of the rear doors
being opened from inside.
Turn the switch on each rear door
a quarter of a turn using the igni-
tion key.
Child safety
Notes:
If one of the doors is open, locking
from the inside and automatic central
locking are not possible.
If the boot is open, automatic central
locking of the doors is active.
Page 77 of 212
ACCESS
69
To switch on
Press and hold button A .
Activation of the function is accom-
panied by a message on the multi-
function display.
Automatic central locking of the
doors
The doors can lock automatically
when you are driving (at a speed of
more than 6 mph (10 km/h)).
Above 6 mph (10 km/h), press button
A
b r i e l y t o u n l o c k t h e d o o r s t e m p o r a r i l y .
You can activate or deactivate this
function .
To switch off
Press and hold button A .
Deactivation of the function is ac-
companied by a message on the
multifunction display. "Door open" alert
If a door has not been closed properly:
-
when the engine is running ,
you are warned by a diagram and
a message on the multifunction
display for a few seconds,
- when the vehicle is moving
(speed above 6 mph (10 km/h)),
the service warning light comes on.
This is accompanied by an audible
signal, a message and a diagram
on the multifunction display for a few
seconds.
This prevents either of the rear doors
being opened from inside.
Turn the switch on each rear door
a quarter of a turn using the igni-
tion key.
Child safety
Notes:
If one of the doors is open, locking
from the inside and automatic central
locking are not possible.
If the boot is open, automatic central
locking of the doors is active.