2006 SUZUKI SX4 AIR

Downloaded from www.Manualslib.com manuals search engine Air Bag System: 8B-16
) B1057Passenger seat belt
pretensioner circuit shorted to
groundPassenger seat belt pretensioner
circuit has been shorted to
ground for more than 4 sec.• Passenger seat belt
pretensioner circuit
•SDM
) B1058Passenger seat belt
pretensioner circuit shorted to
power supplyPassenger seat belt pretensioner
circuit has been shorted to power
circuit for more than 4 sec.
) B1061Driver side-air bag circuit high
resistance Driver side-air bag circuit is more
than 3.7 Ω for more than 4 sec.• Driver side-air bag circuit
• Driver side-air bag module
•SDM ) B1062Driver side-air bag circuit low
resistance Driver side-air bag circuit is less
than 1.0 Ω for more than 4 sec.
) B1063Driver side-air bag circuit
shorted to groundDriver side-air bag circuit has
been shorted to ground for more
than 4 sec.• Driver side-air bag circuit
•SDM
) B1064Driver side-air bag circuit
shorted to power supplyDriver side-air bag circuit has
been shorted to power supply for
more than 4 sec.
) B1065Passenger side-air bag circuit
high resistance Passenger side-air bag circuit is
more than 3.7 Ω for more than 4
sec.• Passenger side-air bag circuit
• Driver side-air bag module
•SDM
) B1066Passenger side-air bag circuit
low resistance Passenger side-air bag circuit is
less than 1.0 Ω for more than 4
sec.
) B1067Passenger side-air bag circuit
shorted to groundPassenger side-air bag circuit
has been shorted to ground for
more than 4 sec.• Passenger side-air bag circuit
•SDM
) B1068Passenger side-air bag circuit
shorted to powerPassenger side-air bag circuit
has been shorted to power circuit
for more than 4 sec.
) B1071Driver forward impact-sensor
communication data
inconsistent Driver forward impact-sensor
has been communicated with no
response or inconsistent ID code
for more than 4 sec.• Driver forward impact-sensor
• Driver forward impact-sensor
circuit
•SDM
) B1072Driver forward impact-sensor
communication data invalid Driver forward impact-sensor
has been communicated with
invalid data for more than 4 sec.• Driver forward impact-sensor
•SDM
)
B1073Driver forward impact-sensor
circuit shorted to groundDriver forward impact-sensor
circuit has been shorted to
ground for more than 4 sec.• Driver forward impact-sensor
• Driver forward impact-sensor
circuit
•SDM ) B1074Driver forward impact-sensor
circuit openDriver forward impact-sensor
circuit has been shorted to power
circuit or opened for more than 4
sec.
) B1081Driver side impact-sensor no
responseDriver side impact-sensor has
been communicated with no
response for more than 4 sec.• Driver side impact-sensor
circuit
• Driver side impact-sensor
•SDM
) B1082Driver side impact-sensor
communication data invalidDriver side impact-sensor has
been communicated with invalid
data for more than 4 sec.• Driver side impact-sensor
•SDM
) B1083Driver side impact-sensor
circuit shorted to groundDriver side impact-sensor circuit
has been shorted to ground for
more than 4 sec.• Driver side impact-sensor
circuit
• Driver side impact-sensor
•SDM ) B1084Driver side impact-sensor
circuit openDriver side impact-sensor circuit
has been shorted to power circuit
or opened for more than 4 sec. DTC No. Detecting itemDetecting condition
(DTC will set when detecting)Trouble area

Downloaded from www.Manualslib.com manuals search engine 8B-17 Air Bag System:
) B1085Driver side impact-sensor
communication data
inconsistent Driver side impact-sensor has
been communicated with
inconsistent ID code for more
than 4 sec.• Driver side impact-sensor
•SDM
) B1091Passenger side impact-sensor
no responseCommunication with passenger
side impact-sensor has been no
response for more than 4 sec.• Passenger side impact-sensor
circuit
• Passenger side impact-sensor
•SDM
) B1092Passenger side impact-sensor
communication data invalidPassenger side impact-sensor
has been communicated with
invalid data for more than 4 sec.• Passenger side impact-sensor
circuit
•SDM
) B1093Passenger side impact-sensor
circuit shorted to groundPassenger side impact-sensor
circuit has been shorted to
ground for more than 4 sec.
• Passenger side impact-sensor
•SDM
) B1094Passenger side impact-sensor
circuit openPassenger side impact-sensor
circuit has been shorted to power
circuit or opened for more than 4
sec.
) B1095Passenger side impact-sensor
communication data
inconsistentPassenger side impact-sensor
has been communicated with
inconsistent ID code for more
than 4 sec.• Passenger side impact-sensor
•SDM
) B1361Driver curtain-air bag circuit
high resistanceDriver curtain-air bag circuit is
more than 3.8 Ω for more than 4
sec. • Driver curtain-air bag circuit
• Driver curtain-air bag module
•SDM
) B1362Driver curtain-air bag circuit low
resistanceDriver curtain-air bag circuit is
less than 1.0 Ω for more than 4
sec.
) B1363Driver curtain-air bag circuit
shorted to groundDriver curtain-air bag circuit has
been shorted to ground for more
than 4 sec.• Driver curtain-air bag circuit
•SDM
) B1364Driver curtain-air bag circuit
shorted to powerDriver curtain-air bag circuit has
been shorted to power circuit for
more than 4 sec.
) B1365Passenger curtain-air bag
circuit high resistancePassenger curtain-air bag circuit
is more than 3.8 Ω for more than
4 sec.• Passenger curtain-air bag
circuit
• Passenger curtain-air bag
module
•SDM ) B1366Passenger curtain-air bag
circuit low resistancePassenger curtain-air bag circuit
is less than 1.0 Ω for more than 4
sec.
) B1367Passenger curtain-air bag
circuit shorted to groundPassenger curtain-air bag circuit
has been shorted to ground for
more than 4 sec.• Passenger curtain-air bag
circuit
•SDM
) B1368Passenger curtain-air bag
circuit shorted to powerPassenger curtain-air bag circuit
has been shorted to power circuit
for more than 4 sec. DTC No. Detecting itemDetecting condition
(DTC will set when detecting)Trouble area

Downloaded from www.Manualslib.com manuals search engine Air Bag System: 8B-18
DTC CheckS6RW0D8204004
1) Turn ignition switch to OFF position.
2) Connect SUZUKI scan tool to data link connector
(DLC) located on underside of instrument panel at
driver’s seat side.
Special tool
(A): SUZUKI scan tool
3) Turn ignition switch to ON position.
4) Read DTC according to instructions displayed on
SUZUKI scan tool and print it or write it down. Refer
to SUZUKI scan tool operator’s manual for further
details.
If communication between scan tool and SDM is not
possible, check if scan tool is communicable by
connecting it to SDM in another vehicle. If
communication is possible in this case, scan tool is
in good condition. Then check data link connector
and serial data line (circuit) in the vehicle with which
communication was not possible.
If connector and circuit are OK, check that DLC
circuit and power supply and ground circuits of SDM
are in good condition referring to “SDM Power
Supply and Ground Circuit Check” and “Serial Data
Link Circuit Check”.
5) After completing the check, turn ignition switch to
OFF position and disconnect SUZUKI scan tool from
data link connector (DLC) (1).
DTC ClearanceS6RW0D8204005
1) Turn ignition switch to OFF position.
2) Connect SUZUKI scan tool to data link connector
(DLC) (1) in the same manner as when making this
connection for DTC check.
Special tool
(A): SUZUKI scan tool
3) Turn ignition switch to ON position.
4) Erase DTC according to instructions displayed on
SUZUKI scan tool. Refer to SUZUKI scan tool
operator’s manual for further details.
5) After completing the clearance, perform “DTC
Check” and confirm that normal DTC (NO CODES)
is displayed and not malfunction DTC.
6) Turn ignition switch to OFF position and disconnect
SUZUKI scan tool from DLC.
NOTE
If DTC B1013, DTC B1021 or DTC B1027 is
stored in SDM, it is not possible to clear DTC.

Scan Tool DataS6RW0D8204006
Data list of SDM
I5RW0A820010-03
Scan Tool DataNormal Condition /
Reference Value
) Buck Up Volt 27.0 – 33.0 V
) Battery Voltage 10 – 14 V
) Driv Air Bag Ini Res 1.5 – 5.0 ohm
) Pass Air Bag Ini Res 1.0 – 3.8 ohm
) Driv Preten Ini Res 1.0 – 3.8 ohm
) Pass Preten Ini Res 1.0 – 3.8 ohm
) Driv Sidebag Ini Res 1.0 – 3.5 ohm
) Pass Sidebag Ini Res 1.0 – 3.5 ohm
) Driv curtain Ini Res 1.0 – 3.5 ohm
) Pass curtain Ini Res 1.0 – 3.5 ohm
) System ID 4ch or 8ch
I5RW0A820010-03

Downloaded from www.Manualslib.com manuals search engine 8B-19 Air Bag System:
Scan Tool Data Definition
Buck Up Volt (V)
This parameter indicates the capacity of the backup
capacitor installed to maintain the ignition current (as
much as possible) even when the power supply to SDM
that ignites the inflator is shut off.
Battery Voltage (V)
Battery voltage is an analog input signal read by SDM.
Dirv Air Bag Ini Res (Driver air bag initiator
resistance) (ohm)
This parameter indicates the resistance of the driver air
bag initiator circuit.
Pass Air Bag Ini Res (Passenger air bag initiator
resistance) (ohm)
This parameter indicates the resistance of the passenger
air bag initiator circuit.
Driv Preten Ini Res (Driver pretensioner initiator
resistance) (ohm)
This parameter indicates the resistance of the driver seat
belt pretensioner initiator circuit.Pass Preten Ini Res (Passenger pretensioner
initiator resistance) (ohm)
This parameter indicates the resistance of the passenger
seat belt pretensioner initiator circuit.
Driv Sidebag Ini Res (Driver side-air bag initiator
resistance) (ohm)
This parameter indicates the resistance of the driver
side-air bag initiator circuit.
Pass Sidebag Ini Res (Passenger side-air bag
initiator resistance) (ohm)
This parameter indicates the resistance of the passenger
side-air bag initiator circuit.
Driv curtain Ini RES (Driver side curtain-air bag
initiator resistance) (ohm)
This parameter indicates the resistance of the driver side
curtain-air bag initiator circuit.
Pass curtain Ini RES (Passenger side curtain-air bag
initiator resistance) (ohm)
This parameter indicates the resistance of the passenger
side curtain-air bag initiator circuit.
System ID (4ch/8ch)
This parameter indicates the number of initiator circuits.
“AIR BAG” Warning Light Comes ON SteadyS6RW0D8204007
Wiring Diagram
“L04”14
5
9RED
RED/BLK GRN
YEL/BLK
BLK
8 7
11
12
15
L04-2
L04-28
L04-27
“G241” “G271” “L313”
13
12V
6
1BLK
WHT WHT
WHT/RED 2
34
310 BLK
“G273”
“E324”
I6RW0C820005-01
1. Battery 5. “IGN” fuse 9. “METER” fuse 13. Light driver
2. Main fuse 6. Ignition switch 10. “DOME” fuse 14. SDM
3. Fuse 7. Junction block assembly 11. Combination meter 15. Ground for SDM
4. Individual circuit fuse box No.1 8. “A/B” fuse 12. “AIR BAG” warning light

Downloaded from www.Manualslib.com manuals search engine Air Bag System: 8B-20
Troubleshooting
Step Action Yes No
1Was “Air Bag Diagnostic System Check Flow” performed?Go to Step 2. Go to “Air Bag
Diagnostic System
Check Flow”.
2SDM power supply and ground circuit check
1) Check SDM power supply and ground circuit referring to
“SDM Power Supply and Ground Circuit Check”.
Is SDM power supply and ground circuit in good condition?Go to Step 3. Repair defective power
supply and ground
circuit.
3“AIR BAG” warning light circuit check
1) Disconnect combination meter connector “G241”
referring to “Combination Meter Removal and Installation
in Section 9C”.
2) Disconnect SDM connector “L04”.
3) Check for proper connection to SDM connector at
terminal “L04-2”.
4) Check for proper connection to combination meter at
terminal “G241-5”.
5) If OK, measure resistance between “G241-5” and “L04-
2” terminals.
Special tool
(A): 09932–76010
Is measured resistance 1
Ω or less?Go to Step 4. Repair “YEL/BLK” wire
(between combination
meter and SDM
connector) for open or
high resistance.
4“AIR BAG” warning light circuit check
1) Measure resistance between “L04-2” terminal and body
ground.
Special tool
(A): 09932–76010
Is measured resistance infinity?Go to Step 5. Repair “YEL/BLK” wire
(between combination
meter and SDM
connector) for short to
ground.
(A)
“L04-2”
“G241-5”
I7RW01822006-01
“L04-2”(A)
I7RW01822007-01

Downloaded from www.Manualslib.com manuals search engine 8B-21 Air Bag System:
NOTE
Upon completion of inspection and repair work, perform the following items.
• Reconnect all air bag system components and ensure all components are properly mounted.
• Repeat “Air Bag Diagnostic System Check” to confirm that the trouble has been corrected.

5“AIR BAG” warning light circuit check
1) Connect SDM connector “L04” and combination meter
connector “G241”.
2) With ignition switch turned ON, measure voltage
between “G241-5” terminal and body ground.
Special tool
(A): 09932–76010
Is measured voltage in 8 – 12 V?Replace combination
meter.Go to Step 6.
6“AIR BAG” warning light circuit check
1) Disconnect combination meter connector “G241”.
2) Measure voltage between “G241-5” terminal and body
ground.
Special tool
(A): 09932–76010
Is measured voltage in 10 – 14 V?Replace combination
meter.Replace SDM. Step Action Yes No
“G241-5”(A)
I7RW01822008-01
“G241-5”(A)
I7RW01822008-01

Downloaded from www.Manualslib.com manuals search engine Air Bag System: 8B-22
“AIR BAG” Warning Light Does Not Come ONS6RW0D8204008
Wiring Diagram
Refer to ““AIR BAG” Warning Light Comes ON Steady”.
Troubleshooting
NOTE
Upon completion of inspection and repair work, perform the following items.
• Reconnect all air bag system components and ensure all components are properly mounted.
• Repeat “Air Bag Diagnostic System Check” to confirm that the trouble has been corrected.

Step Action Yes No
1Was “Air Bag Diagnostic System Check Flow” performed?Go to Step 2. Go to “Air Bag
Diagnostic System
Check Flow”.
2Combination meter power feed circuit check
1) Set parking brake.
2) Note combination meter when ignition switch is turned
ON.
Does the “BRAKE” indicator (warning light) come ON?Go to Step 3. Check combination
meter power and
ground circuit referring
to “C-1 Combination
Meter Circuit Diagram
(Meter) in Section 9A”.
3“AIR BAG” warning light circuit check
1) Disconnect SDM connector “L04”.
2) Note combination meter when ignition switch is turned
ON.
Does the “AIR BAG” warning light come ON?Substitute a known-
good SDM and recheck.Go to Step 4.
4“AIR BAG” warning light circuit check
1) Disconnect SDM connector “L04”.
2) With ignition switch turned ON, measure voltage
between “L04-02” terminal and body ground.
Special tool
(A): 09932–76010
Is measured voltage 0 V?Replace combination
meter.Repair “YEL/BLK”
circuit for short to power
circuit.
(A)“L04-2”
I7RW01822135-01

Downloaded from www.Manualslib.com manuals search engine 8B-23 Air Bag System:
Serial Data Link Circuit CheckS6RW0D8204051
Wiring Diagram
1
2
3
3
18
12V
RED 7
14 9
10
“L313”
“G273”
YEL/BLKL04-2
L04-27 “L04”
PPL/WHT
“G04”L04-3212V
8
GRN
15
+BB
56WHTWHT
4
BLUBLU
BLK
16
11
12
“G241”
13
BLK
L04-28
RED/BLK
WHT/REDYEL/BLK
BLK“G271”
“G272”
WHT/RED
BLK/
ORNBLK
B
C
A A
A
17
[A]
A
[B]
12V
PPL/WHTYEL14
17A
A
YELL04-37
12V
I6RW0C820006-01
[A]: Junction block with BCM model 4. Individual circuit fuse box No.1 12. “METER” fuse
[B]: Junction block without BCM model (That
is, TAIWAN spec model)5. “IGN” fuse 13. “A/B” fuse
A: Serial data circuit 6. Ignition switch 14. BCM
B: DLC power supply circuit 7. Combination meter 15. Data link connector (DLC)
C: DLC ground circuit 8. “AIR BAG” warning light 16. Ground for air system
1. Battery 9. Light driver 17. To HVAC control module (auto A/C model)
2. Main fuse 10. Junction block assembly 18. SDM
3. Fuse 11. “DOME” fuse