2006 RENAULT SCENIC Power Assisted Steering Workshop Manual

POWER ASSISTED STEERING
Fault finding - Interpretation of faults
36B
36B - 17V6 MR-366-X84-36B000$462_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
DF033
PRESENT
OR
STOREDMULTIPLEX NETWORK
DEF : CAN connection fault
NOTESSpecial notes:
Although stored in the computer, this fault is not caused by an electric power-assisted
steering failure, but by a multiplex network fault.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after the engine is started or a steering wheel movement
from full lock to full lock.
Check that:
–there is a + 12 V before ignition feed on track 1 of the electric power steering black 2-track connector,
–there is an earth on track 2 of the electric power steering black 2-track connector,
–there is a + 12 V after ignition feed on track 8 of the steering column assembly black 8-track connector.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise change the wiring.
Check the continuity of the wiring harness for the multiplex network (see 88B, Multiplexing):
Black 8-track connector track 5CAN_L
Black 8-track connector track 7CAN_H
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Multiplex network: repair),
repair the multiplex connection, otherwise change the multiplex connection.
Check the continuity of the wiring harness for the multiplex network (see 88B, Multiplexing)
Black 8-track connector track 4CAN_L instrument panel
Black 8 track connector track 6CAN_H instrument panel
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Multiplex network: repair),
repair the multiplex connection, otherwise change the multiplex connection.
Carry out a multiplex network test and deal with any faults.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
DAETRW_V04_DF033/DAETRW_V08_DF033/DAETRW_V06_DF033/DAETRW_V0C_DF033/
DAETRW_V12_DF033

POWER ASSISTED STEERING
Fault finding - Interpretation of faults
36B
36B - 18V6 MR-366-X84-36B000$462_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
DF035
PRESENT
OR
STOREDVARIABLE POWER ASSISTED STEERING MOTOR
DEF : Internal electronic fault
WARNING
For TRW EPAS Vdiag 04 only, consult the fault contexts.
–If PR143 Internal fault code = 58 and if the battery voltage when the fault occurs (PR108) is above 9 V, do not
clear the fault; contact the Techline.
–If PR143 Internal fault code = 58 and if the battery voltage when the fault occurs (PR108) is less than or equal
to 9 V, run fault finding on the battery and charge circuit.
–For other values of PR143, do not clear the fault, contact the Techline.
For the other Vdiag of TRW EPAS, do not clear the fault, contact the Techline.
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after starting or a steering wheel movement from full lock
to full lock.
Special notes:
Apply the fault finding procedure only on Vdiag 04.
For Vdiag 06, 08, 0C and 12, do not clear the fault and contact the Techline.
–Check the condition and connection of the battery terminals.
–Check that the EPAS black 2-track connector is correctly locked.
–Check that the EPAS black 8-track connector is correctly locked.
–Check the condition and conformity of the EPAS fuses: on the power fuse board (70A) and on the UPC (5A).
–Check the conformity of PR108 Computer feed voltage: 12 V < PR108 < 16 V.
Check that:
–there is a + 12 V before ignition feed on track 1 of the electric power steering black 2-track connector,
–there is an earth on track 2 of the electric power steering black 2-track connector,
–there is a + 12 V after ignition feed on track 8 of the steering column assembly black 8-track connector.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise change the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
DAETRW_V04_DF035/DAETRW_V08_DF035/DAETRW_V06_DF035/DAETRW_V0C_DF035/
DAETRW_V12_DF035

POWER ASSISTED STEERING
Fault finding - Interpretation of faults
36B
36B - 19V6 MR-366-X84-36B000$462_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
DF038
PRESENT
OR
STOREDANGLE SENSOR
DEF : Sensor internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after a steering wheel movement from full lock to full lock
or a road test.
Check that:
–there is a + 12 V before ignition feed on track 1 of the electric power steering black 2-track connector,
–there is an earth on track 2 of the electric power steering black 2-track connector,
–there is a + 12 V after ignition feed on track 8 of the steering column assembly black 8-track connector.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise change the wiring.
Program the steering wheel angle sensor using command VP004 Steering wheel angle sensor programming.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
DAETRW_V04_DF038/DAETRW_V08_DF038/DAETRW_V06_DF038/DAETRW_V0C_DF038/
DAETRW_V12_DF038

POWER ASSISTED STEERING
Fault finding - Interpretation of faults
36B
36B - 20V6 MR-366-X84-36B000$462_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
DF053
PRESENT
COMPUTER CONFIGURATION
DEF : Computer calibration not carried out
NOTESSpecial notes:
This fault appears after the engine is started.
Configure the computer using command SC001 Computer calibration, in line with the equipment and vehicle
type.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
DAETRW_V04_DF053P/DAETRW_V08_DF053P/DAETRW_V06_DF053P/DAETRW_V0C_DF053P/
DAETRW_V12_DF053P

POWER ASSISTED STEERING
Fault finding - Interpretation of faults
36B
36B - 21V6 MR-366-X84-36B000$462_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
DF054
PRESENT
OR
STOREDTORQUE SENSOR
DEF : Sensor internal electronic fault
NOTESWhen the fault appears as present or stored, do not clear the fault.
IMPORTANT
This fault is a safety fault. It may occur intermittently.
Contact the Techline.
AFTER REPAIRNone
DAETRW_V04_DF054/DAETRW_V08_DF054/DAETRW_V06_DF054/DAETRW_V0C_DF054/
DAETRW_V12_DF054

POWER ASSISTED STEERING
Fault finding - Interpretation of faults
36B
36B - 22V6 MR-366-X84-36B000$462_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
DF055
PRESENT
OR
STOREDCOMPUTER MEMORY
DEF : EEPROM irregularity
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after the battery is disconnected.
Check that:
–there is a + 12 V before ignition feed on track 1 of the electric power steering black 2-track connector,
–there is an earth on track 2 of the electric power steering black 2-track connector,
–there is a + 12 V after ignition feed on track 8 of the steering column assembly black 8-track connector.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise change the wiring.
Configure the computer using command SC001 Computer calibration, in line with the equipment and vehicle
type.
If the fault is still present, without customer complaints, the EPAS is secure.
If the fault is still present and the assistance level is severely reduced, contact the Techline.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
DAETRW_V04_DF055/DAETRW_V08_DF055/DAETRW_V06_DF055/DAETRW_V0C_DF055/
DAETRW_V12_DF055

POWER ASSISTED STEERING
Fault finding - Interpretation of faults
36B
36B - 23V6 MR-366-X84-36B000$462_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
DF057
PRESENT
OR
STOREDMULTIPLEX VEHICLE SPEED SIGNAL
DEF : CAN connection fault
NOTESSpecial notes:
Although stored in the computer, this fault is not caused by an electric power-assisted
steering failure, but by a multiplex network fault.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after a road test.
Check that:
–there is a + 12 V before ignition feed on track 1 of the electric power steering black 2-track connector,
–there is an earth on track 2 of the electric power steering black 2-track connector,
–there is a + 12 V after ignition feed on track 8 of the steering column assembly black 8-track connector.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise change the wiring.
Check the continuity of the wiring harness for the multiplex network (see 88B, Multiplexing):
Black 8-track connector track 5CAN_L
Black 8-track connector track 7CAN_H
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Multiplex network: repair),
repair the multiplex connection, otherwise change the multiplex connection.
Run a multiplex network test and make sure there are no faults.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
DAETRW_V04_DF057/DAETRW_V08_DF057/DAETRW_V06_DF057/DAETRW_V0C_DF057/
DAETRW_V12_DF057

POWER ASSISTED STEERING
Fault finding - Interpretation of faults
36B
36B - 24V6 MR-366-X84-36B000$462_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
DF059
PRESENT
OR
STOREDANGLE SENSOR
DEF : Sensor internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after a steering wheel movement from full lock to full lock
or a road test.
Check that:
–there is a + 12 V before ignition feed on track 1 of the electric power steering black 2-track connector,
–there is an earth on track 2 of the electric power steering black 2-track connector,
–there is a + 12 V after ignition feed on track 8 of the steering column assembly black 8-track connector.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise change the wiring.
Program the steering wheel angle sensor using command VP004 Steering wheel angle sensor programming.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
DAETRW_V04_DF059/DAETRW_V08_DF059/DAETRW_V06_DF059/DAETRW_V0C_DF059/
DAETRW_V12_DF059