2006 RENAULT SCENIC ECU

POWER ASSISTED STEERING
Fault finding - Introduction
36B
36B - 3V6 MR-366-X84-36B000$066_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
To cut off the + after ignition feed, proceed as follows:
–disconnect the diagnostic tool,
–press the start button briefly 2 times (less than 3 seconds),
–confirm that the forced + after ignition feed has been cut off by checking that the computer indicator lights on the
instrument panel have gone out.
Faults
Faults are declared as either present or stored (depending on whether they appeared in a certain context and have
disappeared since, or whether they remain present but have not been diagnosed within the current context).
The present or stored status of faults should be taken into consideration when the diagnostic tool is used following
the + after ignition supply being switched on (without acting on the system components).
For a present fault, apply the procedure described in the Interpretation of faults section.
For a stored fault, note the faults displayed and apply the notes section.
If the fault is confirmed when the instructions in the Notes section are applied, the fault is present. Deal with the fault
If the fault is not confirmed, check:
–the electrical lines which correspond to the fault,
–the connectors on these lines (corrosion, bent pins, etc.),
–the resistance of the component detected as faulty,
–the condition of the wires (melted or cut insulation, wear).
Conformity check
The aim of the conformity check is to check data that does not produce a fault on the diagnostic tool when
inconsistent. Therefore, this stage is used to:
–carry out fault finding on faults that do not have a fault display, and which may correspond to a customer
complaint.
–check that the system is operating correctly and that there is no risk of a fault recurring after repairs.
This section gives the fault finding procedures for statuses and parameters and the conditions for checking them.
If a status is not behaving normally or a parameter is outside the permitted tolerance values, consult the
corresponding fault finding page.
Customer complaints - Fault finding chart
If the test with the diagnostic tool is OK but the customer complaint is still present, the fault should be processed by
customer complaint.
A summary of the overall procedure to follow is provided on the following page in the form of a flow chart.

POWER ASSISTED STEERING
Fault finding - Interpretation of faults
36B
36B - 22V6 MR-366-X84-36B000$462_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
DF055
PRESENT
OR
STOREDCOMPUTER MEMORY
DEF : EEPROM irregularity
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after the battery is disconnected.
Check that:
–there is a + 12 V before ignition feed on track 1 of the electric power steering black 2-track connector,
–there is an earth on track 2 of the electric power steering black 2-track connector,
–there is a + 12 V after ignition feed on track 8 of the steering column assembly black 8-track connector.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise change the wiring.
Configure the computer using command SC001 Computer calibration, in line with the equipment and vehicle
type.
If the fault is still present, without customer complaints, the EPAS is secure.
If the fault is still present and the assistance level is severely reduced, contact the Techline.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
DAETRW_V04_DF055/DAETRW_V08_DF055/DAETRW_V06_DF055/DAETRW_V0C_DF055/
DAETRW_V12_DF055

POWER ASSISTED STEERING
Fault finding - Conformity check
36B
36B - 25V6 MR-366-X84-36B000$528_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12POWER ASSISTED STEERING
Fault finding - Conformity check
MAIN SCREEN
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Execution conditions: ENGINE STOPPED, IGNITION ON.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Steering wheel
angleET020:Steering wheel
angle sensor
programmingStatus 4: calibrated
and initialisedIn the event of a fault, consult
the interpretation of status
ET020.
2EngineET023:Engine
operationSTOPPED: engine
stopped.
STALLED: engine
stopped without using
the ignition keyIn the event of a fault, test the
multiplex network.
3Computer
supplyPR108:Computer feed
voltage9 V < X < 16 VIf the computer supply
voltage is not sufficient,
dialogue cannot be
established.
If PR108 is not correct, run
fault finding on the charge
circuit.
4Vehicle speedPR003:Vehicle speed0 mph (0 km/h) when
stationaryIn the event of a fault, test the
multiplex network.
5Electric motorPR012:Current
absorbed by the
motor0 A < X < 1 AWithout any action on the
steering wheel.
6Thermal
protectionPR119:Motor thermal
protection
indicatorInterior temperature
± 5 ˚CIf PR119 > 60˚C, thermal
protection is activated.
The assistance level PR140
= 15 %. To deactivate
thermal protection, do not
operate the EPAS for
15 minutes. PR014:Level of
assistance
available99 % or 0 %
depending on Vdiag
15 % if thermal
protection activated.
DAETRW_V04_CCONF/DAETRW_V08_CCONF/DAETRW_V06_CCONF/DAETRW_V0C_CCONF
MR-366-X84-36B000$528_eng.mif

POWER ASSISTED STEERING
Fault finding - Conformity check
36B
36B - 26V6 MR-366-X84-36B000$528_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
SUB-FUNCTION: POWER
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Execution conditions: ENGINE STOPPED, IGNITION ON.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1EngineET023:Engine
operationSTOPPED or
STALLEDIn the event of a fault, test the
multiplex network.
2Computer
supplyPR108:Computer feed
voltage9 V < X < 16 VIf the computer supply
voltage is not sufficient,
dialogue cannot be
established.
If PR108 is not correct, run
fault finding on the charge
circuit.

POWER ASSISTED STEERING
Fault finding - Conformity check
36B
36B - 27V6 MR-366-X84-36B000$528_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
SUB-FUNCTION: ASSISTANCE
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as examples.
Execution conditions: ENGINE STOPPED, IGNITION ON.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Steering
wheel
angleET020:Steering wheel
angle sensor
programmingStatus 4: calibrated
and initialisedIn the event of a fault, refer to
the interpretation of status
ET020.
PR121:Steering wheel
angle0˚ with the wheels set
straight ahead
+ or - 580˚ at full lockIn the event of a fault, consult
the interpretation of PR121.
2Vehicle
speedPR003:Vehicle speed0 mph (km/h) when
stationaryIn the event of a fault, test the
multiplex network.
3TorquePR001:Torque applied to
the steering wheel0 Nm ± 0.2 Nm
with no action on the
steering wheelIn the event of a fault, consult
the interpretation of PR001.
PR006:Steering motor
torque setpoint0 Nm ± 0.2 NmIn the event of a fault, consult
the interpretation of PR006.
4Motor
powerPR012:Current absorbed
by the motor0 A < X < 1 AIn the event of a fault, consult
the interpretation of PR012.
PR013:Setpoint for
current absorbed
by the motor0 A < X < 1 AIn the event of a fault, consult
the interpretation of PR013.
5Thermal
protectionPR119:Motor thermal
protection
indicatorInterior temperature
± 5˚CIf PR119 > 60 ˚C, thermal
protection is activated.
The level of assistance
PR014 = 15 %.
To deactivate the thermal
protection, do not operate the
EPAS for 15 minutes. PR014:Level of
assistance
available0 % or 99 %
depending on Vdiag
15 % if thermal
protection activated.

POWER ASSISTED STEERING
Fault finding - Conformity check
36B
36B - 28V6 MR-366-X84-36B000$528_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
SUB-FUNCTION: ASSISTANCE (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Execution conditions: ENGINE STOPPED, IGNITION ON.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
6Computer
calibrationET026:Computer
calibrationConfiguration 1 to 5
according to
equipment and vehicle
type.Redefine the vehicle
specifications using
command SC001 Computer
calibration.