2006 NISSAN VERSA keyless entry

BCM (BODY CONTROL MODULE)
BCS-7
C
D
E
F
G
H
I
J
L
MA
B
BCS
Revision: June 20062007 Versa

BCM is activated with low current consumption mode.

CAN communication is not active.

When CAN communication operation is detected, it switches to CAN communication status.

When a state of the following switches changes, it switches to CAN communication state:
–Ignition switch
–Key switch (without Intelligent Key)
–Key switch and ignition knob switch (with Intelligent Key)
–Hazard switch
–Door lock/unlock switch
–Front door switch (LH, RH)
–Rear door switch (LH, RH)
–Back door lock assembly
–Combination switch (passing, lighting switch 1st position, front fog lamp)
–Keyfob (lock/unlock signal)
–Front door key cylinder switch LH

When control performed only by BCM is required by switch, it shifts to CAN communication inactive
mode.

Status of combination switch reading function is changed.
SYSTEMS CONTROLLED BY BCM DIRECTLY

Power door lock system. Refer to BL-23, "POWER DOOR LOCK SYSTEM" .

Remote keyless entry system. Refer to BL-54, "REMOTE KEYLESS ENTRY SYSTEM" .

Power window system. Refer to GW-17, "POWER WINDOW SYSTEM" . NOTE

Room lamp timer. Refer to LT- 9 1 , "INTERIOR ROOM LAMP" .

Rear wiper and washer system. Refer to WW-30, "REAR WIPER AND WASHER SYSTEM" .
NOTE:
Power supply only. No system control.
SYSTEMS CONTROLLED BY BCM AND IPDM E/R

Panic system. Refer to BL-54, "REMOTE KEYLESS ENTRY SYSTEM" .

Vehicle security (theft warning) system. Refer to BL-193, "VEHICLE SECURITY (THEFT WARNING)
SYSTEM" .

NVIS(NATS) system. Refer to BL-212, "NATS (Nissan Anti-Theft System)" .

Headlamp, tail lamp and battery saver control systems. Refer to LT- 7 5 , "PARKING, LICENSE PLATE AND
TA I L L A M P S" , LT- 5 , "HEADLAMP (FOR USA)" or LT-27, "HEADLAMP (FOR CANADA) - DAYTIME
LIGHT SYSTEM -" .

Front fog lamp. Refer to LT-41, "FRONT FOG LAMP" .

Front wiper and washer system. Refer to WW-4, "FRONT WIPER AND WASHER SYSTEM" .

Rear window defogger system. Refer to GW-50, "REAR WINDOW DEFOGGER" .
SYSTEMS CONTROLLED BY BCM AND COMBINATION METER

Warning chime. Refer to DI-47, "WARNING CHIME" .

Turn signal and hazard warning lamps. Refer to LT- 5 1 , "TURN SIGNAL AND HAZARD WARNING
LAMPS" .
SYSTEMS CONTROLLED BY BCM AND INTELLIGENT KEY UNIT

Intelligent Key system. Refer to BL-80, "INTELLIGENT KEY SYSTEM" .

BCS-8
BCM (BODY CONTROL MODULE)
Revision: June 20062007 Versa
MAJOR COMPONENTS AND CONTROL SYSTEM
CAN Communication System DescriptionEKS00I82
Refer to LAN-4, "SYSTEM DESCRIPTION" .
System Input Output
Remote keyless entry systemRemote keyless entry receiver
(keyfob)

All door locking actuators

Turn signal lamp (LH, RH)

Combination meter (turn signal lamp)
Intelligent Key system Intelligent Key unit

All door locking actuators

Turn signal lamp (LH, RH)

Combination meter (turn signal lamp)
Power door lock systemFront power door lock/unlock
switch (LH, RH)All door locking actuators
Power supply (IGN) to power window Ignition power supply Power supply to power window system
Power supply (BAT) to power window Battery power supply Power supply to power window system
Panic alarm

Key switch

KeyfobIPDM E/R
Battery saver control

Ignition switch

Combination switchIPDM E/R
Headlamp Combination switch IPDM E/R
Tail lamp Combination switch IPDM E/R
Front fog lamp Combination switch IPDM E/R
Turn signal lamp Combination switch

Turn signal lamp

Combination meter
Hazard lamp Hazard switch

Turn signal lamp

Combination meter
Room lamp timer

Key switch

Keyfob

Main power window and door
lock/unlock switch

Front door switch LH

All door switchInterior room lamp
Key warning chime

Key switch

Front door switch LHCombination meter (warning buzzer)
Light warning chime

Combination switch

Key switch

Front door switch LHCombination meter (warning buzzer)
Seat belt warning chime

Seat belt buckle switch LH

Ignition switchCombination meter (warning buzzer)
Front wiper and washer system

Combination switch

Ignition switchIPDM E/R
Rear window defogger Rear window defogger switch IPDM E/R
Rear wiper and washer system

Combination switch

Ignition switchRear wiper motor
A/C switch signal Front air control ECM
Blower fan switch signal Front air control ECM
A/C indicator signal Front air control A/C indicator
Low tire pressure warning system Remote keyless entry receiver Combination meter

BCS-12
BCM (BODY CONTROL MODULE)
Revision: June 20062007 Versa
Terminals and Reference Values for BCMEKS00I85
Te r m i n a lWire
colorSignal nameSignal
input/
outputMeasuring condition
Reference value or waveform
(Approx.) Ignition
switchOperation or condition
2BRCombination switch
input 5Input ONLighting, turn, wiper OFF
Wiper dial position 4
3GRCombination switch
input 4Input ONLighting, turn, wiper OFF
Wiper dial position 4
4LCombination switch
input 3Input ONLighting, turn, wiper OFF
Wiper dial position 4
5GCombination switch
input 2
Input ONLighting, turn, wiper OFF
Wiper dial position 4
6VCombination switch
input 1
7BRFront door key cylin-
der switch LH (unlock)Input
OFFON (open, 2nd turn) Momentary 1.5V
OFF (closed) 0V
8YFront door key cylin-
der switch LH (lock)InputOn (open) Momentary 1.5V
OFF (closed) 0V
9WRear window defog-
ger switchInput ONRear window defogger switch
ON0V
Rear window defogger switch
OFF5V
11 LIgnition switch (ACC
or ON)InputACC or
ONIgnition switch ACC or ON Battery voltage
12 SB Front door switch RH Input OFFON (open) 0V
OFF (closed) Battery voltage
13 GR Rear door switch RH Input OFFON (open) 0V
OFF (closed) Battery voltage
15 WTire pressure warning
check connectorInput OFF — 5V
18 VRemote keyless entry
receiver (ground)Output OFF — 0V
SKIA5291E
SKIA5292E
SKIA5291E
SKIA5292E

BCM (BODY CONTROL MODULE)
BCS-13
C
D
E
F
G
H
I
J
L
MA
B
BCS
Revision: June 20062007 Versa
19 BRRemote keyless entry
receiver (power sup-
ply)Output OFF Ignition switch OFF
20 GRemote keyless entry
receiver signal (sig-
nal)Input OFFStand-by (keyfob buttons
released)
When remote keyless entry
receiver receives signal from
keyfob (keyfob buttons
pressed)
21 P NATS antenna amp.Input/
OutputOFF →
ONIgnition switch (OFF → ON)Just after turning ignition switch
ON: Pointer of tester should
move for approx. 1 second, then
return to battery voltage.
23 RSecurity indicator
lampOutput OFFGoes OFF → illuminates
(Every 2.4 seconds)Battery voltage → 0V
25 LG NATS antenna amp.Input/
OutputOFF →
ONIgnition switch (OFF → ON)Just after turning ignition switch
ON: Pointer of tester should
move for approx. 1 second, then
return to battery voltage.
26 GR Thermo control amp. Input ON A/C switch ON
27 OCompressor ON sig-
nalInput ONA/C switch OFF 5V
A/C switch ON 0V
28 P Front blower monitor Input ONFront blower motor OFF Battery voltage
Front blower motor ON 0V
29 L Hazard switch Input OFFON 0V
OFF 5V
30
*1VBack door open out-
putOutput —Back door open (switch
closed)0V
Back door closed (switch
open)5V
30
*2VBack door opener
switchInput —All doors locked (SW OFF) Battery voltage
All doors unlocked (SW ON) 0V TerminalWire
colorSignal nameSignal
input/
outputMeasuring condition
Reference value or waveform
(Approx.) Ignition
switchOperation or condition
LIIA1893E
LIIA1894E
LIIA1895E
ZJIA0719J

BCM (BODY CONTROL MODULE)
BCS-17
C
D
E
F
G
H
I
J
L
MA
B
BCS
Revision: June 20062007 Versa
CONSULT-II Function (BCM)EKS00I87
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II START PROCEDURE
Refer to GI-38, "CONSULT-II Start Procedure" .
ITEMS OF EACH PART
NOTE:
CONSULT-II will only display systems the vehicle possesses.
BCM diagnostic
test itemDiagnostic mode Content
Inspection by partWORK SUPPORTSupports inspections and adjustments. Commands are transmitted to the BCM
for setting the status suitable for required operation, input/output signals are
received from the BCM and received data is displayed.
DATA MONITOR Displays BCM input/output data in real time.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
SELF-DIAG RESULTS Displays BCM self-diagnosis results.
CAN DIAG SUPPORT
MNTRThe results of transmit/receive diagnosis of CAN communication can be read.
ECU PART NUMBER BCM part number can be read.
CONFIGURATION Performs BCM configuration read/write functions.
System and itemCONSULT-II dis-
playDiagnostic test mode (Inspection by part)
WORK
SUPPORTSELF−
DIAG
RESULTSCAN DIAG
SUPPORT
MNTRDATA
MONITORECU
PA R T
NUMBERACTIVE
TESTCON-
FIGU-
RATION
BCM BCM×× × × ×
Power door lock sys-
temDOOR LOCK×××
Rear defoggerREAR DEFOG-
GER××
Warning chime BUZZER××
Room lamp timer INT LAMP×××
Remote keyless entry
systemMULTI REMOTE
ENT×××
Headlamp HEAD LAMP×××
Wiper WIPER×××
Turn signal lamp
Hazard lampFLASHER××
Blower fan switch sig-
nal
Air conditioner switch
signalAIR CONDI-
TIONER×
Intelligent KeyINTELLIGENT
KEY×
Combination switch COMB SW×
NVIS (NATS) IMMU××
Interior lamp battery
saverBATTERY
SAVER×××
Back door TRUNK××
Theft alarm THEFT ALARM×××
Retained accessory
power controlRETAINED PWR×××

BCM (BODY CONTROL MODULE)
BCS-23
C
D
E
F
G
H
I
J
L
MA
B
BCS
Revision: June 20062007 Versa
7. Touch “WRITE CONFIGURATION” on “SELECT CONFIG
ITEM” screen.
8. Touch "YES”.
For canceling, touch "NO".
9. Using the following flow chart, identify the correct model and configuration list. Confirm and/or change set-
ting value for each item according to the configuration list.
Depending on CONSULT-II software version being used, some or all of the write configuration items
shown in the following configuration lists may be displayed. If an item does not appear on the CONSULT-
II "WRITE CONFIGURATION" screen(s), then it is an auto setting item and it cannot be manually set or
changed.
NOTE:
Confirm vehicle model on IDENTIFICATION PLATE. Refer to GI-47, "
Model Variation" .
10. Touch "CHNG SETTING" on "WRITE CONFIGURATION" screen.
CAUTION:
Make sure to touch "CHNG SETTING" even if the indicated configuration of brand-new BCM is
same as the desirable configuration.
If not, configuration which is set automatically by selecting vehicle model cannot be memorized.
11. Touch “OK” on "WRITE CONFIGURATION" screen.
If "CANCEL" is touched, it will return to previous screen.
LKIA0547E
LKIA0175E
ITEM SET VAL
KEYLESS ENTRY WITH ⇔ WITHOUT
I-KEY WITH ⇔ WITHOUT
DTRL WITH ⇔ WITHOUT
THEFT ALARM WITH ⇔ WITHOUT
LKIA0397E

BL-2Revision: June 20062007 Versa Door Lock Actuator Check (Front RH and Rear LH/
RH) ......................................................................... 49
Front Door Key Cylinder Switch LH Check ............. 50
Passenger Select Unlock Relay Circuit Check (With
Intelligent Key) ........................................................ 51
REMOTE KEYLESS ENTRY SYSTEM ..................... 54
Component Parts and Harness Connector Location ... 54
System Description ................................................. 55
INPUTS ............................................................... 55
OPERATED PROCEDURE ................................. 56
CAN Communication System Description .............. 56
Schematic ............................................................... 57
Wiring Diagram — KEYLES — ............................... 58
............................................................................. 58
Terminals and Reference Values for BCM .............. 61
How to Perform Trouble Diagnoses ........................ 61
Preliminary Check .................................................. 61
CHECK BCM CONFIGURATION ........................ 61
CONSULT-II Function (BCM) .................................. 61
CONSULT-II START PROCEDURE .................... 61
CONSULT-II APPLICATION ITEMS .................... 61
Work Flow ............................................................... 64
Trouble Diagnosis Symptom Chart ......................... 64
Keyfob Battery and Function Check ....................... 66
ACC Switch Check ................................................. 67
Door Switch Check ................................................. 68
Key Switch (Insert) Check ...................................... 70
Hazard Function Check .......................................... 71
Horn Function Check .............................................. 71
Interior Lamp and Ignition Keyhole Illumination
Function Check ....................................................... 72
Remote Keyless Entry Receiver Check .................. 73
Keyfob Function (Lock) Check ............................... 75
Keyfob Function (Unlock) Check ............................ 75
ID Code Entry Procedure ....................................... 76
KEYFOB ID SET UP WITH CONSULT-II ............ 76
KEYFOB ID SET UP WITHOUT CONSULT-II ..... 77
Keyfob Battery Replacement .................................. 78
Removal and Installation of Remote Keyless Entry
Receiver ................................................................. 79
REMOVAL ........................................................... 79
INSTALLATION .................................................... 79
INTELLIGENT KEY SYSTEM ................................... 80
Component Parts and Harness Connector Location ... 80
System Description ................................................. 82
DOOR LOCK/UNLOCK FUNCTION ................... 83
KEY REMINDER FUNCTION .............................. 85
REMOTE KEYLESS ENTRY FUNCTIONS ......... 86
ENGINE START FUNCTION ............................... 89
WARNING CHIME/BUZZER/LAMPS FUNC-
TION .................................................................... 90
CHANGE SETTINGS FUNCTION ....................... 93
INTELLIGENT KEY REGISTRATION .................. 93
STEERING LOCK SOLENOID REGISTRATION ... 93
CAN Communication System Description .............. 93
Schematic ............................................................... 94
Wiring Diagram — I/KEY — ................................... 96
Intelligent Key Unit Harness Connector Terminal
Layout ...................................................................106Terminals and Reference Values for Intelligent Key
Unit ........................................................................ 106
Steering Lock Solenoid Harness Connector Termi-
nal Layout ............................................................. 108
Terminals and Reference Values for Steering Lock
Solenoid ................................................................ 108
Terminals and Reference Values for BCM ............ 108
Trouble Diagnosis Procedure ................................ 109
PRELIMINARY CHECK ..................................... 109
WORK FLOW ....................................................110
CONSULT-II Functions (INTELLIGENT KEY) ....... 111
CONSULT-II Start Procedure ................................ 111
BASIC OPERATION .......................................... 111
CONSULT-II Application Items .............................. 111
SELF-DIAGNOSTIC RESULTS ......................... 111
DATA MONITOR ................................................ 111
ACTIVE TEST ....................................................112
WORK SUPPORT .............................................113
Trouble Diagnosis Symptom Chart .......................114
KEY WARNING LAMP (GREEN) ILLUMINATES .114
KEY WARNING LAMP (RED) ILLUMINATES ...114
KEY WARNING LAMP DOES NOT ILLUMINATE .115
NON DTC ITEM .................................................115
ENGINE START CONDITION CHECK ..............116
ALL FUNCTIONS OF INTELLIGENT KEY SYS-
TEM DO NOT OPERATE ..................................116
DOOR LOCK/UNLOCK FUNCTION MALFUNC-
TION ..................................................................116
REMOTE KEYLESS ENTRY FUNCTION MAL-
FUNCTION ........................................................118
HAZARD AND BUZZER REMINDER FUNC-
TION MALFUNCTION .......................................119
WARNING CHIME/BUZZER FUNCTION MAL-
FUNCTION ........................................................ 120
WARNING LAMP FUNCTION MALFUNCTION . 122
CAN Communication System Check .................... 122
Power Supply and Ground Circuit Check ............. 123
Key Switch (Intelligent Key Unit Input) Check ....... 124
Key Switch (BCM Input) Check ............................. 126
Ignition Knob Switch Check .................................. 127
Door Switch Check ............................................... 129
Door Request Switch Check ................................. 132
Back Door Request Switch Check ........................ 134
Unlock Sensor Check ........................................... 136
Intelligent Key Warning Buzzer (Driver Door) Check . 138
Outside Key Antenna (Driver Side and Passenger
Side) Check .......................................................... 139
Outside Key Antenna (Rear Bumper) Check ........ 141
Inside Key Antenna Check .................................... 143
Steering Lock Solenoid Check .............................. 144
Key Interlock Solenoid (With M/T) Check ............. 147
Ignition Switch Position Check .............................. 148
Stop Lamp Switch Check (With CVT) ................... 148
Stop Lamp Switch Check (With M/T) .................... 149
Check CVT Device (Park Position Switch) Check . 151
“P-SHIFT” Warning Lamp (With CVT) Check ....... 153
“LOCK” Warning Lamp (With M/T) Check ............. 154
“KEY” Warning Lamp (RED) Check ...................... 155
“KEY” Warning Lamp (GREEN) Check ................. 156

BL-3
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa Check Warning Chime in Combination Meter ...... 156
Hazard Function Check ........................................ 157
Horn Function Check ........................................... 157
Headlamp Function Check ................................... 158
Intelligent Key Battery Replacement .................... 159
DISASSEMBLY AND ASSEMBLY OF INTELLI-
GENT KEY ........................................................ 159
INTELLIGENT KEY BATTERY INSPECTION ... 159
Remote Keyless Entry Function ........................... 159
Removal and Installation of Intelligent Key Unit ... 160
REMOVAL ......................................................... 160
INSTALLATION ................................................. 160
DOOR ..................................................................... 161
Fitting Adjustment ................................................ 161
FRONT DOOR .................................................. 161
REAR DOOR .................................................... 163
BACK DOOR ..................................................... 164
Removal and Installation ...................................... 165
FRONT DOOR .................................................. 165
REAR DOOR .................................................... 166
BACK DOOR ..................................................... 167
FRONT DOOR LOCK ............................................. 169
Component Parts Location ................................... 169
Removal and Installation ...................................... 169
REMOVAL ......................................................... 169
INSTALLATION ................................................. 171
REAR DOOR LOCK ............................................... 172
Component Parts Location ................................... 172
Removal and Installation ...................................... 172
REMOVAL ......................................................... 172
INSTALLATION ................................................. 174
BACK DOOR LOCK ............................................... 175
Component Parts and Harness Connector Location . 175
System Description .............................................. 176
Wiring Diagram — TLID — .................................. 177
WITHOUT INTELLIGENT KEY SYSTEM ......... 177
WITH INTELLIGENT KEY SYSTEM ................. 178
Terminals and Reference Values for BCM ........... 179
Terminals and Reference Values for Intelligent Key
Unit ....................................................................... 179
CONSULT-II Function (BCM) ............................... 179
CONSULT-II START PROCEDURE .................. 179
CONSULT-II APPLICATION ITEMS .................. 180
Work Flow ............................................................ 180
Trouble Diagnosis Chart by Symptom .................. 180
BCM Power Supply and Ground Circuit ............... 180
Check Back Door Opener Switch Circuit (Without
Intelligent Key or Power Windows) ...................... 181
Check Back Door Opener Switch Circuit (Without
Intelligent Key, With Power Windows) .................. 184
Check Back Door Opener Switch Circuit (With Intel-
ligent Key) ............................................................ 187
Check Back Door Lock Assembly (Actuator) Circuit . 189
Removal and Installation ...................................... 190
BACK DOOR LOCK .......................................... 190
BACK DOOR HANDLE ..................................... 191FUEL FILLER LID OPENER ...................................192
Removal and Installation of Fuel Filler Lid Opener .192
REMOVAL .........................................................192
INSTALLATION .................................................192
VEHICLE SECURITY (THEFT WARNING) SYSTEM .193
Component Parts and Harness Connector Location .193
System Description ...............................................194
DESCRIPTION ..................................................194
POWER SUPPLY AND GROUND ....................194
INITIAL CONDITION TO ACTIVATE THE SYS-
TEM ...................................................................195
VEHICLE SECURITY SYSTEM ALARM OPER-
ATION ................................................................195
VEHICLE SECURITY SYSTEM DEACTIVATION .195
PANIC ALARM OPERATION ............................195
CAN Communication System Description ............196
Schematic .............................................................197
Wiring Diagram — VEHSEC — ............................198
..........................................................................198
Terminals and Reference Values for BCM ............202
Terminals and Reference Values for Intelligent Key
Unit .......................................................................202
CONSULT-II Function (BCM) ...............................202
CONSULT-II START PROCEDURE ..................202
CONSULT-II APPLICATION ITEM ....................202
Trouble Diagnosis .................................................204
WORK FLOW ....................................................204
Preliminary Check ................................................205
Symptom Chart .....................................................206
Diagnostic Procedure 1 ........................................207
Diagnostic Procedure 2 ........................................210
Diagnostic Procedure 3 ........................................211
Diagnostic Procedure 4 ........................................211
Diagnostic Procedure 5 ........................................211
Diagnostic Procedure 6 ........................................211
NATS (NISSAN ANTI-THEFT SYSTEM) ................212
Component Parts and Harness Connector Location .212
System Description ...............................................213
DESCRIPTION ..................................................213
SECURITY INDICATOR ....................................213
System Composition .............................................213
ECM Re-communicating Function ........................214
Wiring Diagram — NATS — .................................215
Terminals and Reference Values for BCM ............216
CONSULT-II Function ...........................................216
CONSULT-II INSPECTION PROCEDURE ........216
CONSULT-II DIAGNOSTIC TEST MODE FUNC-
TION ..................................................................217
HOW TO READ SELF-DIAGNOSTIC RESULTS .217
NATS SELF-DIAGNOSTIC RESULTS ITEM
CHART ..............................................................218
Trouble Diagnosis Procedure ...............................219
PRELIMINARY CHECK .....................................219
WORK FLOW ....................................................220
Trouble Diagnoses ...............................................222
SYMPTOM MATRIX CHART 1 ..........................222
SYMPTOM MATRIX CHART 2 ..........................222
Diagnostic Procedure 1 ........................................223
Diagnostic Procedure 2 ........................................225